range

Tried everything to get it out of high range. Have had the tractor for 6 years. Always been hard to change from LMH but now is in H and can't change to medium or low. Thanks, if any knows the problem.

Hi. My Dad has taken a bit ill over the last couple years so I'm now running his hydrostatic CT 445 on his property a lot to deal with hauling some logs around, plowing the driveway, tilling the garden, etc. Last weekend I'd been running the tractor for about 30m with no issues and had to hop...

Looking at new utility tractors in the 100-120hp range. Looking at either an LS MT7101, a kioti hx1151, TYM 115/130 or a Zetor 120. All dealers are an hour or more away so dealer location is trivial unless I want to fork over money for green. Doing field work/row crops, and hay Pros and cons?

have a mccormick x50 that the range shifter is bound, does anyone have a quick fix other than removing the cab and top of trans to get it to shift, TIA

I just recently installed the Dakota Alert DCPA 4K that uses the buried vehicle probe. The transmitter and receiver are located about 1/2 mile away however the transmitter is at the bottom of a hill and my alerts are spotty. Maybe 50/50 success rate at best. I know I can move it closer to the...

Hello. I have about 625 hrs on my tractor. Just was out in the 25F weather clearing snow. Changed to "H" and it was grinding the gears (heard the grinding for about 3-4 clicks and immediately backed off. Went in "H" no issues. Now, the lever is extremely hard to move through the ranges. It...

15 hours on it. Is there a fix for range shifter getting stuck in a gear? This happened when in 4 drive wheel low range. Got it released by taking it out of 4 wheel and rocking forward and back with the shuttle shift. Can this problem be fixed without taking it back to the dealer. I have had it...

I have an NX5010 HST with just the main gear shift lever for low, medium, and high. The gear shift lever started giving me rouble going into high and then after about a week it became completely disengaged just yesterday. The gear shift lever has a roll pin at the bottom of it to attach it to...

70 years old guy is still improving the kitchen.😄😄😄

Reaching the range shifter on our M59 has been a bit awkward and required a more arm and shoulder effort than is comfortable. So I finally got around to improving it for a better personal fit. Here is a simple modification that has worked well. rScotty

While doing backhoe work went to move tractor and it would not move. I had this happen last fall and found the roll pin that holds the shaft and lever together had fallen out i was able to replace the pin with a bolt and nut, this time the shaft will move but it will not engage wheels all other...

All, I looked around to finger out how to change the boots on these (TN 55, 60, 65, 70, 75 cab models). All I learned is that others asked similar questions as well as a locking pin problem (locks the joy stick motion -- sliding collar on the joystick) but didn't list what they did or how they...

I have a slide in range. Model is KSIB900ESS (slide in, convection oven / Induction top) stove. Suffering "F2-E0" error. Frankly, it's been quirky since day one. There are several boards inside. I'm trying to ascertain which one I need to replace. Had a repair guy out here a year or so...

Hello 1900hrs on my 08 1547 had all new engine oil filter trans fluid and filters. He out April tdh in it. I see it says meets some massey specs. Started it hot was on a slight incline in high range and when i went to take off it had a delay. Got to checking fluid and it maybe down a little...

A new TYM owner here. A few months ago I bought a one year old T474 HST with 270 hours. The dealer told me he had sold the tractor as new and all maintenance had been done at his shop and the tractor was in great shape. As an aside but not relevant to my current problem, the tractor needed...

I've dug through the forums here and even read some scholarly articles on the subject but I still don't understand how revs affect the performance of the HST when using hydraulic implements like a loader. I can feel the difference it makes in pulling, cutting and ground engaging implements but...