rebuild

The kit is from W.R Long. Where can I get gaskets and seals for this? Has anyone had this issue before? Part# VKMH1538L. 5336659

Good afternoon, all, I recently added a IH B275 to the work team. The price was good; thus, the condition was way below par. Researching for exactly what model this B275 was, became very interesting! All data I could find indicates that the last B275 manufactured had a serial number of around...

Hello everyone, I am looking to see if anyone knows how to disassemble the gear and bearings of a 5540 hesston gearbox PTO. My baler had a sleeve that connected the pto shaft to the gearbox shaft. The shaft sheered the pin and it slid down striping the ends of the shaft. I was going to...

I am helping a friend rebuild his YM226D and we are almost finished, just repaint left to do. He is missing the right side engine cover. Anybody know where one might be that we could buy?

Hello, currently rebuilding an iseki E3CD engine on a used MT265b. I could definitely tell someone was already in that engine before. Here is my issue . The spring placements on the rack arm for the injection pump. I know one goes from the pin on the block to the rack arm but not sure about...

Does anyone have recommendations for a reputable shop that does turbo rebuilds?

Rebuilt and installed: Got the trans installed and noticed I cannot get it to roll freely when manually pushing. I figured let’s just see what happens when there is pressure from a running motor. Fired her up and had to adjust the bypass lever a bit but I was able to get it going in forward...

I've got a GT275 that is really hard to start; with a squirt of starter fluid she will fire up and run pretty well. I was thinking of rebuilding the card but all I see available are gasket sets (or a new REALLY expense carb). What do folks recommend here?

Remote for planter seed gate stopped working, Best way to rebuild??

I was bush hogging and a stick found itd way through thr grill and into the radiator. (I only have the attached screenshot atm) Ive been reading around and I see there are some quality issues with new radiators. There is a shop that rebuilds radiators about 45 minutes away. I'm not even sure...

I have an FM72 that honestly has been nothing but a pain of late. I had a spindle go bad last year and opted to replace them all as it is a bit older anyway and several of them were a bit sloppy. All was fine until recently when one of the new ones basically blew out on me not sure if that is a...

Good evening from Maine, My friend owns a long 550 tractor with a 1550 loader. His lift cylinders are leaking by and he wants to rebuild them, but can't find part information due to the tractors orphan status. Does anyone have any ideas about sourcing packing, other than taking the cylinders to...

Hello Everyone. I've owned a Digit 198T for 20 years and its ability has become weaker. Main pump transmission part # 40-03-7500 must have a rebuild kit somewhere. Is there another part name or part number for this pump? I saw someone posted that a John Deere 300's pump parts work with some...

Hey all! You do not have to purchase any special tools or pay a shop to install these difficult to install seals. Here is an easy DIY I found and had my mechanic watch it and perform the procedure. It does seem easier if the vice jaws are smaller. I think the best twine/rope to use is a smooth...

I purchased a kawasaki mule a few days ago, I looked it over and have decided to do a rebuild of sorts. I can't do a stock restoration on anything, it's just not in me to do that, I have to do it my way! For reference, This is my 2000 JD LT133 it's on its third hood, y'all know how bad these...

This is a 2106 5055E cab tractor with 12x12 PR transmission with 800+ hours bought at auction that needed a rebuild. I drove this tractor and even loaded it after purchase. I have no previous history for it. When I got it home, it barely had enough compression to crank, but had no lights on the...

I have a kioti ds4510 that overheated that causing scars on the cylinders. Trying to locate oversized pistons/rings (87.5mm) any hel point to acquire those parts would be greatly appreciated. Engine model is 4a220lwe and the standard size of pistons are 87mm

First rebuild in all the years I've owned it. Had the seals and 'O' rings on the shelf as it has been leaking for a while but the outboards hold quite a bit of 85-140 and I kept an eye on the level so all was good. Was a job removing the outer right side outboard (it's a heavy, over 100 pound...

My three-point lift stopped lifting. My FEL still works as it should. I took the top lid off to rebuild the cylinder and found this broke part. I assume it has something to do with the draft. 1. Does this broke part have anything to do with the three point not working? 2. Can I just remove...

After cleaning them up, should 9N head bolts be installed dry, oiled, or anti siezed? Proper torque? Thanks, Knots

I am trying to put in service a White 543 4 row corn planter. I need a parts manual & a parts supplier. The fert hoppers have been exposed to weather & I don't know if they are fixable. I plan to clean & oil if I can get them apart. I have gone through the seed hoppers & I think they're ok...

I have one of those 15 gal firmco sprayers and it seems like the pump is getting weaker. I e had it for about 5 years and was wondering if anyone knows if you can rebuild the pump or do you just have to buy a new one? thanks

I'm trying to fix a slow JD 67 loader on a JD 750 tractor with a SCV off a ford or new holland ("diesel kiki" branded). I can't find any parts or service info for it, and am new to hydraulics, but generally mechanically competent. So just a couple questions QUESTION: Are the external spool...

I live in the Temecula Area of SoCal and want to get the MAX28 rebuilt. Wondering if anyone has any suggestions ? Thanks for your time.

Howdy folks! It's been a while. OK, so it's not that I'm a slacker... it's just that I bust a$$ all the time and there are some projects I never seem to get to. I've been 'kicking the can' on my leaking backhoe cylinders for years. I have a bunch of cat litter pans that I keep under the...

Just got done rebuilding the engine coupler, found all the parts required. listing the part numbers from Neapco but may be crossed reference, they are 1000 series PTO yokes. I measured and found the dimensions at https://www.neapcoaftermarket.com/wp-content/uploads/2019/11/2001ptocatalog637.pdf...

Sooo, my new to me my 2005 LW8 backhoe has one cylinder which has a leaky seal. The cylinder rod had some spotty rust which upon cleaning up still had finger nail noticable abrasion. On the time sucking vortex it seems the cylinder rod could be brazed and cleaned up, with new seals then...

I started a rebuild on my little 850(yanmar 2500). Back story is it got hot the other day and seemed to have blew the head gasket , so I dove into the motor and found what looked like a bad head gasket, small groove in middle cylinder wall and the connecting rod bearing in pieces all on the...

I started a rebuild on my little 850. Back story is it got hot the other day and seemed to have blew the head gasket , so I dove into the motor and found what looked like a bad head gasket, small groove in middle cylinder wall and the connecting rod bearing in pieces all on the middle cylinder...

Yesterday at a flea market I picked up the above blower for cheap. I am getting a little frustrated with it.. it will run on ether (just enough to test). But it is not getting gas. Pickup Filter is relatively clear, fuel line is in good shape. I want to get a rebuild kit for the carburetor...

Hey guys, I’m rebuilding a Mott 60 flail mower I picked up for $200. I’ve priced out the parts I need and it’ll run me around $650. The bearings and housings are almost $160 per side. Ive cleaned everything up as best I can. My concern is on the cuttershaft ends. One side looks good but the...

Hello I have TA25 loader and am wanting to rebuild the cylinders. I am able to get the tilt/bucket rams out as they are held with a simple snap ring. However I can't figure out how to remove the lift cylinders. The end had a steel plate with two slots in it. I don't see a snap ring or how...

I'm doing a complete rebuild of the engine for my New Holland T1030. The engine is a Shibaura S773L. The block is cracked in several places and also has a hole in it (threw a rod), so I'm replacing the entire block. I'm not a diesel mechanic by any means but I am willing to tinker and learn. I...