2210
- Thread starter pruntyc
- Start date
- Views: 3736
arthr31
Platinum Member
Thanks, Mark.
mark777
Veteran Member
- Joined
- May 16, 2004
- Messages
- 1,300
- Location
- S.E Texas
- Tractor
- Ym1300d-1401D-1601D , 1610D & Massey Ferguson 1020
Dick / Arthr,
I try to use the information from www.TractorData.com. I seems to be fairly accurate, and occasionally updated. NOT GOSPEL, but next best thing to a IT shop manual with weights & measurements.
Mark
I try to use the information from www.TractorData.com. I seems to be fairly accurate, and occasionally updated. NOT GOSPEL, but next best thing to a IT shop manual with weights & measurements.
Mark
normde2001
Elite Member
- Joined
- Mar 10, 2002
- Messages
- 4,163
Some listings may be "dry weight", others with fluids. I doubt that anyone other than Yanmar really knows.
Mickey_Fx
Veteran Member
My numbers agree with Mark and they came from www.yanmarowners.com
arthr31
Platinum Member
hmm... that chart might be suspect... they listed the height of the 2210 at 74 inches. That'd make it 6ft 1in. My 1601 is listed at 59 inches.
But, i guess as a relative reference point, it's OK...
OK, like i said, i'm considering upgrading from 1601 (and 169) to a single 2210. I have woodlands, field down the road to mow (about 1 acre few to several times a summer), and about 1/2 acre to finish mow, few hundred feet of dirt/gravel driveway to maintain. Also, I'll be doing a lot of digging and moving stone this coming summer.
Why get rid of the 1601? Sometimes it seems like it's pushed around with some of the tasks and I'd like to get a tractor that is not remanufactored. my current loader seems kinda flimsy and I've concerns about the longevity of the "rebuild" (how long will it last...)
Is the 2210 too much for my applications? Should I just take the longer times it'll take with the 1601?
Thanks for the input guys... -art
But, i guess as a relative reference point, it's OK...
OK, like i said, i'm considering upgrading from 1601 (and 169) to a single 2210. I have woodlands, field down the road to mow (about 1 acre few to several times a summer), and about 1/2 acre to finish mow, few hundred feet of dirt/gravel driveway to maintain. Also, I'll be doing a lot of digging and moving stone this coming summer.
Why get rid of the 1601? Sometimes it seems like it's pushed around with some of the tasks and I'd like to get a tractor that is not remanufactored. my current loader seems kinda flimsy and I've concerns about the longevity of the "rebuild" (how long will it last...)
Is the 2210 too much for my applications? Should I just take the longer times it'll take with the 1601?
Thanks for the input guys... -art
buppy69
Platinum Member
The height is including the exhaust stack.
Eugene
Eugene
arthr31
Platinum Member
ah.. OK, that kinda make sense.... tall tractor! thanks Eugene -Art
vongiese
Silver Member
- Joined
- Mar 29, 2002
- Messages
- 165
- Location
- NW Montana
- Tractor
- Yanmar 2210D, Sany SY35 Excavator, Kubota 4060LE,
The 3 cylinder runs a bit smoother than the 2 cylnder - by nature. The creeper gear range is unreal. And the rear universal lock is a nice addiiton. 2210 has a water pump and my 2210D has the nice tranny - can't remember what it's referred to now - basically the clutch is optional and is real handy with FEL work. With the option to use the breaks on one wheel you can turm some pretty tight corners. Looks like the 2210 is only 7" lomger and 2" wider. I don't think it's be too much.
Get a good factory built loader!!!
good luck!
Get a good factory built loader!!!
good luck!