stnickstoys
Gold Member
Could anyone with pics of 3pt hitches they made please post. Looking for ideas for F15 F16 Yannie 3 pt hitch conversion
Nick
Nick
3pt hitch
- Thread starter stnickstoys
- Start date
- Views: 10228
Redfisher
Silver Member
- Joined
- Mar 25, 2002
- Messages
- 178
- Location
- Fergus, Ontario,Canada
- Tractor
- Cub Cadets 104,129,149, Jinma 284
Hello
Do you mean a 3pt hitch for a tractor that does not have one?
or a hitch for your 3pt.
Do you mean a 3pt hitch for a tractor that does not have one?
or a hitch for your 3pt.
OP
stnickstoys
Gold Member
I meant converting grey market tractors with 2 pt tillers to a standard Cat 1 3 pt. I will be constructing all brackets from scratch and was wondering what others are doing
Re: 3pt hitch (Specs)
Don't know if they are ANSI specs. but here is what I understand of the cat. specs that apply to the Cat 1 size equipment which is commonly used. • Cat "1", apparently aimed at for 20-45 hp equipment; pins on top link bar 3/4" dia at both ends; bottom pins 7/8" dia. at implement with 26" spacing between pins being standard. Beyond that, everything varies, which is why 3-point hitch has flexible adjustments:• Dimensions on length of top link bars varies with implements you use but my bar usually is set at 24-25" long.• Lift pin heights above ground at implement vary also. Maybe 12"-18" above ground with implement sitting on ground.• Top link pin height above ground on some of my implements is 28"-36" above ground with implement sitting on ground. Commercial agriculture uses heavier Cat 2 or 3 specs. Light Cat 0 is sometimes seen on very small tractors but it is not very common. Cat 1 is readily available.
Don't know if they are ANSI specs. but here is what I understand of the cat. specs that apply to the Cat 1 size equipment which is commonly used. • Cat "1", apparently aimed at for 20-45 hp equipment; pins on top link bar 3/4" dia at both ends; bottom pins 7/8" dia. at implement with 26" spacing between pins being standard. Beyond that, everything varies, which is why 3-point hitch has flexible adjustments:• Dimensions on length of top link bars varies with implements you use but my bar usually is set at 24-25" long.• Lift pin heights above ground at implement vary also. Maybe 12"-18" above ground with implement sitting on ground.• Top link pin height above ground on some of my implements is 28"-36" above ground with implement sitting on ground. Commercial agriculture uses heavier Cat 2 or 3 specs. Light Cat 0 is sometimes seen on very small tractors but it is not very common. Cat 1 is readily available.
Re: 3pt hitch (Photos)
I can post some of the basic photos I have of hitches but this forum seems to have a restrictive size limit on posting drawings & photos. I have some detailed plans & marked-up photos of hitches & parts but they exceed the forum's size limit so I can't post them. I tried but they could not be posted. If you want to see the detailed stuff we will have to use snail-mail and photocopies. Which I am willing to do if you want to see them and if you are willing to pay the postage. Contact me via the private message feature and I'll try to help you. One photo attached to this message. It is rear end of my tractor when I first removed the tiller: dirty, rusty, two lift arms but no three point hitch.
I can post some of the basic photos I have of hitches but this forum seems to have a restrictive size limit on posting drawings & photos. I have some detailed plans & marked-up photos of hitches & parts but they exceed the forum's size limit so I can't post them. I tried but they could not be posted. If you want to see the detailed stuff we will have to use snail-mail and photocopies. Which I am willing to do if you want to see them and if you are willing to pay the postage. Contact me via the private message feature and I'll try to help you. One photo attached to this message. It is rear end of my tractor when I first removed the tiller: dirty, rusty, two lift arms but no three point hitch.
Attachments
And another view of the JD Green. These hitches are OK but the top link bracket has only one pin position & is only held by two bolts and the lift arm connectors on these designs have a fixed clevis where they attach to the lower lift bar, which I have found can bind. I have converted to a looser clevis & no longer get any binding when raising & lowering various implements.
Attachments
Towbar assembly which I have built into the 3-point hitch rig. Original tractor had only a flat drawplate with a hole in it. I can still use that but I was able to weld a piece of 2x2 box into the initial hitch setup so that I can also slide a towing bar into the rear end and use my choice of a ball, pintle or towing shackle. Sticks far enough out so I can hook up & tow things without having to remove things or make a lot of changes.
Attachments
Ym1401King
Bronze Member
Re: 3pt hitch (Specs)
I just built my 3-pt lift arms and used 23" as the inside width. I guess its back to the drawing board. I was told 23", not 26".
Also, where did you get that threaded bolt that has the cat. 1 lift arm pin for the top of your lift arm linkages? I just used a piece of 1/2" rod with a piece that is welded at a 90, and is inserted into the lift arm piece on the tractor, and has a clevis on the other end that connects to the lift arm itself.
Aric
YM1401/w3tcompact/icons/king.gif
I just built my 3-pt lift arms and used 23" as the inside width. I guess its back to the drawing board. I was told 23", not 26".
Also, where did you get that threaded bolt that has the cat. 1 lift arm pin for the top of your lift arm linkages? I just used a piece of 1/2" rod with a piece that is welded at a 90, and is inserted into the lift arm piece on the tractor, and has a clevis on the other end that connects to the lift arm itself.
Aric
YM1401/w3tcompact/icons/king.gif
Re: 3pt hitch (Specs)
26" pin spacing is the norm and that's with the ball joints tightened in place on the implement. On implements with the pins facing outward, you have to initially spread the lower lift arms maybe 32" apart to fit them on the pins, then move them inward to their working position. I use inward-facing pins on my mower so I have to push the lift arms together to maybe 20-22" spacing and then push them outward & pin them in place. I use a big rubber mallet when I hook up to help drive the arms into place on the pins. The lift arm connectors I used on my final version of my hitch were made from a couple of standard top link bars I bought at the local farm store. Look at the drawing I posted. I like to be able to adjust connector arm length on both sides of my hitch; that lets you accurately level implements & to adjust to different implements. I found a couple of all-steel Cat. "0" top link bars that adjusted from 10.5" to 16" long and they had 5/8" ID ball joints at both ends. They were based on 3/4" RH/LH threaded rods so they were plenty strong. They were not intended as connectors but they were ideal for converting to connectors. You could also use them to make good strong stabilizers. They were made in India. My all-time favorite place down here in SE U.S. is a franchise outfit called Agri-Supply Company. They have best selection/prices on farm supplies & tractor parts. They have a website (www.Agri-Supply.com) and a toll-free (1-800-345-0169) and I think you can order by mail. No, I do not work for them. I just give them my business because they are competent & fair. They sold these toplinks for $6.50 each. Their catalogue #33343. I have seen other farm stores asking $20+ apiece for the same bars. Rip off. I just cut the ball joint off one end of a bar and welded my clevis mechanism in place. I prefer the flexible clevis to one that is rigidly welded in place. Then you simply bolt everything in place: ball joint at top connects to hydraulic lift arm and allows smooth rotation; clevis at bottom bolts to lower lift arm and does not bind. Use good strong bolts & lock washers & cotter pins. As these arms work up & down, bolts/nuts can work loose unless you take precautions. Also use the lock nuts on the connectors to fix their length once you get them adjusted.
26" pin spacing is the norm and that's with the ball joints tightened in place on the implement. On implements with the pins facing outward, you have to initially spread the lower lift arms maybe 32" apart to fit them on the pins, then move them inward to their working position. I use inward-facing pins on my mower so I have to push the lift arms together to maybe 20-22" spacing and then push them outward & pin them in place. I use a big rubber mallet when I hook up to help drive the arms into place on the pins. The lift arm connectors I used on my final version of my hitch were made from a couple of standard top link bars I bought at the local farm store. Look at the drawing I posted. I like to be able to adjust connector arm length on both sides of my hitch; that lets you accurately level implements & to adjust to different implements. I found a couple of all-steel Cat. "0" top link bars that adjusted from 10.5" to 16" long and they had 5/8" ID ball joints at both ends. They were based on 3/4" RH/LH threaded rods so they were plenty strong. They were not intended as connectors but they were ideal for converting to connectors. You could also use them to make good strong stabilizers. They were made in India. My all-time favorite place down here in SE U.S. is a franchise outfit called Agri-Supply Company. They have best selection/prices on farm supplies & tractor parts. They have a website (www.Agri-Supply.com) and a toll-free (1-800-345-0169) and I think you can order by mail. No, I do not work for them. I just give them my business because they are competent & fair. They sold these toplinks for $6.50 each. Their catalogue #33343. I have seen other farm stores asking $20+ apiece for the same bars. Rip off. I just cut the ball joint off one end of a bar and welded my clevis mechanism in place. I prefer the flexible clevis to one that is rigidly welded in place. Then you simply bolt everything in place: ball joint at top connects to hydraulic lift arm and allows smooth rotation; clevis at bottom bolts to lower lift arm and does not bind. Use good strong bolts & lock washers & cotter pins. As these arms work up & down, bolts/nuts can work loose unless you take precautions. Also use the lock nuts on the connectors to fix their length once you get them adjusted.
