5' Rotary Cutter Options

[Rock Crawler]

RC, what is the difference between '306-1-TW' and '306-2-TW'?
Not seeing anything in the documentation. Thanks!

View attachment 716104

Single tail wheel (what I just bought) vs a dual rear tail wheels. View attachment 716133View attachment 716134

 

[Rock Crawler]

Here you can see the single and the smooth top heavy Guage steel.

 

[Bearsixty7]

RC, what is the difference between '306-1-TW' and '306-2-TW'?
Not seeing anything in the documentation. Thanks!

I believe 1 Tailwheel vs 2 tailwheels

 

[Bearsixty7]

Very strange, but it has happened before. I didn't see a response to the question but after posting, It shows RC posted a few minutes before I did..

 

[Rock Crawler]

I understand that other people can have a different experience, but my Titan 72" cutter has bent every time it has had a chance. The specs look good but it looks twice as rough as my Brushbull even though is has been used less than 1/2 as much. I do contract mowing, so I subject it to more abuse,

I'm calling BS.... not because your BSing but because there are 2 Titan companies and many are unaware.

There is Titan Implements who are in Tennessee I believe. Products cut, bent, welded and assembled in USA.

Titan's headquarters and manufacturing facility is located in Decatur, Tennessee and was established in 2014 by father and son team, Mike and Baily Turner.

HOME | Not Sure

www.titanimplement.com

Then you have the China crap Titan. Also known as PalletForks.com.

Tractor Pallet Forks Attachments | Titan Attachments

We have a wide variety of Tractor implements and attachments for all your equipment needs. Low Prices and Free Shipping Sitewide on all Pallet Forks, Grapples, Hay Frames, and more.

www.palletforks.com

 

[kenmac]

I was meaning the one that you have and use behind the MX

5ft

 

[LD1]

5ft

Isn't that a little small?

I'd think it would look funny behind a mx.... Let alone your bigger tractor

 

[kenmac]

Isn't that a little small?

I'd think it would look funny behind a mx.... Let alone your bigger tractor

yes, it is . lol. I don't bush hog very often . cows eat most of the grass.
I do have some small areas that works well with this small cutter, small 1-2'' saplings every now and again.

I had an older 6 footer that I sold some time back, and this is the only one I have at this time

It looks real funny behind the CX. The cutter only goes behind it when it's hot out and I want AC lol

I went to LMC (where these cutters are made) to look at a 7 footer but they said they were out at this time. Said they were selling as fast as they can make them. Probably should have kept the 6 footer, but I didn't want to rebuild it. It pretty much needed everything though

 

[oosik]

I've been looking at rotary cutters for a looong time. My choice is down to:

Brown 472 or Rhino TW36. I just haven't "jumped off the ledge" yet.

I will purchase with expected delivery in the spring of 2022.

I prefer the Rhino unit because - local dealers, like the design, stronger tail wheel.

Most ALL my cutting will be backing into brush and cutting field grass.

 

[Bearsixty7]

I've been looking at rotary cutters for a looong time. My choice is down to:

Brown 472 or Rhino TW36. I just haven't "jumped off the ledge" yet.

I will purchase with expected delivery in the spring of 2022.

I prefer the Rhino unit because - local dealers, like the design, stronger tail wheel.

Most ALL my cutting will be backing into brush and cutting field grass.

You should consider a BushHog BH316-2 as well, it's right in there with the Rhino specs and it may b a few hundred cheaper. I do recommend chains front and rear.