TrailHermit
New member
I've recently seen some mention of a mulching kit available for decks on the bx models. I did some searching but haven't seen much on these. If anyone has used this are you happy with the results you get?
bx MMM mulching kit
- Thread starter TrailHermit
- Start date
- Views: 9998
I bought one with my new BX. It came installed. I really didn't have much to mow, and ended up taking it off when I needed to mow some weeds with it. So I really can't evaluate the goodness/badness of it's performance.
But I can tell you it is NOT a quick thing to take off/put on. If you plan to get one, you should install it and be done with it. If/when I get a consistent place to mow, I plan to re-install it.
Sorry I can't be of more assistance to you.
Ron
But I can tell you it is NOT a quick thing to take off/put on. If you plan to get one, you should install it and be done with it. If/when I get a consistent place to mow, I plan to re-install it.
Sorry I can't be of more assistance to you.
Ron
Mike_Lipke
Silver Member
- Joined
- Oct 25, 2005
- Messages
- 205
- Tractor
- Kubota BX1500
I'd be happy if I could figure out a way to just block the chute on deck. I'm trying to mulch leaves, and that thing has so much power that the leaves don't get chopped up too much, they just end up two counties away. If anyone has fabricated a chute block so that the leaves stay under the deck a little longer, pictures and/or description would be great
Volfandt
Veteran Member
I did a mulch plug project on my BX23's 60"MMM as a winter project and after a full season of usage I've got mixed reviews out of it's performance.
It did pretty good on my front 1 acre lot as long as I kept up on it. A minimum of once a week was required to keep it up. Let it get away and I'd have to either slow down to a crawl or go back over the small windrows that it left.
It didn't do very well at all in the tall stuff in my lower lying field. It grows much faster & thicker than the front yard. I discarded the plug midway through the summer and went back to side discharging into windrows, then I would run over the windrows several times with the mulch plug installed.
I eventually added a Cyclone Rake to my arsenal and use it to pickup those windrows now.
I have a huge amount of leaves that fall annually and the mulch plug was not able to grind them up enough, hense the Cyclone Rake.
I didn't try the mulching blades though, and I still may try them out before it's all said and done beause I'm still going to use the plug when mowing the front next season.
Volfandt
Link
It did pretty good on my front 1 acre lot as long as I kept up on it. A minimum of once a week was required to keep it up. Let it get away and I'd have to either slow down to a crawl or go back over the small windrows that it left.
It didn't do very well at all in the tall stuff in my lower lying field. It grows much faster & thicker than the front yard. I discarded the plug midway through the summer and went back to side discharging into windrows, then I would run over the windrows several times with the mulch plug installed.
I eventually added a Cyclone Rake to my arsenal and use it to pickup those windrows now.
I have a huge amount of leaves that fall annually and the mulch plug was not able to grind them up enough, hense the Cyclone Rake.
I didn't try the mulching blades though, and I still may try them out before it's all said and done beause I'm still going to use the plug when mowing the front next season.
Volfandt
Link
Schultz
Gold Member
I liked the gator mulching blades that I recently put on my bx 60" mower. I've only mowed my three acres three times with it. However I did see it as a definite improvement and worth the $65. The grass and leaves are definitely more chewed up. It also sucks up the grass and wet grass/leaves much better.
I used blade #90-987 which is made for another Kubota deck that has 1.125" spindles. I made bushings to reduce the diameter to the correct diameter. These blades have higher lift than standard blades, so they do make a little more noise.
Tim
I used blade #90-987 which is made for another Kubota deck that has 1.125" spindles. I made bushings to reduce the diameter to the correct diameter. These blades have higher lift than standard blades, so they do make a little more noise.
Tim
IndyChris
New member
I purchased the kit for my 60" bx deck, due to the amount of hay the mower was making.
The kit consisted of 2 baffle "plates" for the upper part of the deck, then an additional left baffle plate, and the 3 blades. I think I had about 300 into the whole deal when I was done.
It was a fairly straightforward install, just required alligning the plates and drilling a few holes. Nothing more than a few hrs to finish.
I am pretty happy with the results. It takes the major volume area out of the picture, and really does a nice job of chopping the clippings. I have ran mine thru some fairly tall stuff, and it just walks right thru.
It isn't a super perfect cut, like some are expecting, but its not hack looking at all. If you dont try to go too fast, it does pretty good. I would like to see more lift from the blades, but gators are always an option there.
I will enclose a few pics of the install, and a chunk of grass I mowed... Posts to follow!
The kit consisted of 2 baffle "plates" for the upper part of the deck, then an additional left baffle plate, and the 3 blades. I think I had about 300 into the whole deal when I was done.
It was a fairly straightforward install, just required alligning the plates and drilling a few holes. Nothing more than a few hrs to finish.
I am pretty happy with the results. It takes the major volume area out of the picture, and really does a nice job of chopping the clippings. I have ran mine thru some fairly tall stuff, and it just walks right thru.
It isn't a super perfect cut, like some are expecting, but its not hack looking at all. If you dont try to go too fast, it does pretty good. I would like to see more lift from the blades, but gators are always an option there.
I will enclose a few pics of the install, and a chunk of grass I mowed... Posts to follow!
