Cab owners - several questions

[cford36]

I know some of this has been posted somewhere but I haven't been able to find it.

- What is the size of the switches on the side post?

- Anyone that has mounted a light bar under the front (or back) eave. Plastic seems flimsy to just drill and mount to. Use a strip of metal on backside to support?

- Does anyone have the wiring diagram of the switches and blanks on the side post?

Thanks

 

[JLwoodworks]

The switches are Carling L series.

I would recommend making a bracket to go from each factory light bracket and not Mount anything to the plastic.

What are you looking for with the switches? There doesn't seem to be any extra wiring for the blanks.

Jay

 

[JLwoodworks]

This may help.

http://www.tractorbynet.com/forums/customization/373521-replaced-cab-lights-led-bars.html?highlight=

 

[Drewmon]

I used the same lights in the link above, both front and rear. I didn't need to modify any brackets. I also bought the wire connectors that were a direct plug in to the OEM light sockets. HUGE difference in light output.

 

[cford36]

I used the same lights in the link above, both front and rear. I didn't need to modify any brackets. I also bought the wire connectors that were a direct plug in to the OEM light sockets. HUGE difference in light output.

You have a link or type of connectors they are?

 

[Drewmon]

You have a link or type of connectors they are?

I bought these from ebay. WIRE PIGTAIL MALE 862 H27 TWO HARNESS

WIRE PIGTAIL MALE 881 H27 TWO HARNESS REPAIR CONNECTOR HIGH HEAT SOCKET ADAPTER | eBay

And these were the lights I used:

Amazon.com: Auxbeam 9” LED Light Bar 54W Off-road Lights Flood Beam Cree Chips Driving Light for Vehicle Pickup Car SUV Truck with Mounting Brackets （Pack of 2）: Automotive

 

[cford36]

I bought these from ebay. WIRE PIGTAIL MALE 862 H27 TWO HARNESS

WIRE PIGTAIL MALE 881 H27 TWO HARNESS REPAIR CONNECTOR HIGH HEAT SOCKET ADAPTER | eBay

And these were the lights I used:

Amazon.com: Auxbeam 9” LED Light Bar 54W Off-road Lights Flood Beam Cree Chips Driving Light for Vehicle Pickup Car SUV Truck with Mounting Brackets （Pack of 2）: Automotive

Just want to double check: you said you bought a 862 but the link you put is for an 881, not sure the difference?

 

[atomchaser]

I installed a piece of square tubing between the existing work light brackets for LED strip lights. I left the factory work lights in place and wired the on/off control for new strip lights to the existing work light switches using a relay. For powering the new lights, I tapped into the fuse block on the left inside column of the cab. I used LED light strips from Amazon. They seem to be holding up okay and put out plenty of light.

 

[JLwoodworks]

Here's the connectors I used.

Amazon.com: 1pcs H11 Socket Car Wire Connector Cable Plug Adapter for HID LED Foglight Head Light L Bulb Led Light: Car Electronics

The bonus too is that it comes with both sides. So I was able to give away my factory lights along with the proper connectors to a friend who has no lights on his tractor cab.

 

[lostcreekranch]

I bought these from ebay. WIRE PIGTAIL MALE 862 H27 TWO HARNESS

WIRE PIGTAIL MALE 881 H27 TWO HARNESS REPAIR CONNECTOR HIGH HEAT SOCKET ADAPTER | eBay

And these were the lights I used:

Amazon.com: Auxbeam 9” LED Light Bar 54W Off-road Lights Flood Beam Cree Chips Driving Light for Vehicle Pickup Car SUV Truck with Mounting Brackets （Pack of 2）: Automotive

Do these plugs mate up to the existing LS cab side light power sockets?