Combination SSQA pallet fork & QH 3 point mount

   / Combination SSQA pallet fork & QH 3 point mount #1  

SSdoxie

Elite Member
Joined
Jun 25, 2010
Messages
2,694
Location
Cumberland Plateau, TN
Tractor
Bobcat CT225
I don't recall who mentioned this on TBN a few months ago about making a 3 point mount on set of QA pallet forks to use on either end of the tractor, but it got me thinking. When I buy rolled hay I have to unload the trailer at the road and haul it back to the barn (about 1/4 mile) with the tractor, so wanted to haul 2 bales per trip. With bale spear on front to off load trailer and stack 2 high in the barn, I decided to see if I could rig up a 3 point, QH compatible, on the pallet forks. Here is what I came up with this weekend.

Started with 2"X2"X1/8" angle iron I had laying around. Notched the top end to fit in under top lip of QA frame and bottom. The small bevel at top is what I had to take off to clear any protrusion that interfered with the QA fit.
2013-07-27 15.46.36.jpg 2013-07-27 15.47.08.jpg

This is thin iron so I made 4 pieces to carry on each side of lift arm.
2013-07-27 15.49.02.jpg

I didn't take progressive photos of the top link connection, but used 1.5"X1.5" angle with some 3" stock welded on for the top link pin. used 1.25" pins @ all 3 locations and tack welded them in since this QH and don't need to remove pins. Here is finished product.
2013-07-28 18.48.41.jpg

It still fits the loader: 2013-07-28 18.47.12.jpg

And fits on 3 point: 2013-07-28 18.52.02.jpg 2013-07-28 18.52.31.jpg 2013-07-28 18.55.14.jpg

Only negative I have seen so far is the lower hooks of QH protrude in way of the fork id trying to relocate/slide past. Have to set the forks either outside the hooks or inside before hooking it to 3 point. 2013-07-28 13.30.14.jpg

If that is only problem, I can easily live with it. Just have to remember to move the forks out, when needed, while pallet frame is hooked on the loader.
 
   / Combination SSQA pallet fork & QH 3 point mount #3  
Now all you need is a second pair of forks so you have a set for the front so you can do both front and rear at the same time. :thumbsup:
 
   / Combination SSQA pallet fork & QH 3 point mount
  • Thread Starter
#4  
Now all you need is a second pair of forks so you have a set for the front so you can do both front and rear at the same time. :thumbsup:

I did this so I could carry 2 bales of hay at same time, have a bale spear for the front. If I use it to carry firewood, I can but pallet fork on front and carry-all on back.
 
   / Combination SSQA pallet fork & QH 3 point mount #5  
I think you will find the forks on the rear very handy.
 

Tractor & Equipment Auctions

2008 John Deere 9570 STS Combine - Front Duals - Premium Cab - 1,704 Sep Hours - Clean & Field-Re... (A50397)
2008 John Deere...
2017 Chevrolet Silverado 3500 HD 4x4 Crew Cab Reading Service Truck (A48081)
2017 Chevrolet...
2014 Volkswagen Jetta Sedan (A50324)
2014 Volkswagen...
2005 Toyota Tundra Limited Crew Cab Pickup Truck (A48081)
2005 Toyota Tundra...
2020 FREIGHTLINER CASCADIA TANDEM AXLE SLEEPER (A50505)
2020 FREIGHTLINER...
2009 Peterbilt 384 T/A Wet Kit Day Cab Truck Tactor (A50323)
2009 Peterbilt 384...
 
Top