mikefinger
New member
I am taking possession of a 1952 Ferguson TO 30. Is there a way to add hydraulics to this tractor? It has a working 3 point hitch and is in pretty good condition over all.
Ferguson Hydraulics
- Thread starter mikefinger
- Start date
- Views: 1500
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
it HAS hyds.
the 3pt isn't lifted by magic!!!
you can tap the 3pt hyds by chaining them down and diverting oil to a valve to run.. say.. a lift implement wheel cyl.. or to a OC valve for a loader.
you can also add a stinger pump and then have your choice of flow rates and capacity pumps..
the 3pt isn't lifted by magic!!!
you can tap the 3pt hyds by chaining them down and diverting oil to a valve to run.. say.. a lift implement wheel cyl.. or to a OC valve for a loader.
you can also add a stinger pump and then have your choice of flow rates and capacity pumps..
OP
mikefinger
New member
Thanks, I knew the 3pt was hydraulic because Ferguson didn't develop the magic 3pt hitch until much later. Lol. I could have worded that better. I was wanting to add remotes to run other implements. Is a stinger a pump that runs off the pto? If so that sounds like it would give better flexibility of possible implements.
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
stinger pumps run off the crank snout.. pto pumps are available. BUT.. with a non live pto. it can be a hassle.. and also sometimes it messe sup 3pt geometry fro implements that use the pto.. even with a passthru long pto stub.
pto pump is usually cheaper and easier to setup than a stinger pump.. so no free lunch either way.
if you just needed low flow and temp use.. again.. like a lift wheel on a pull implemnent.. you can chainthe lift and use diverted flow witht he 3pt control for a sa lift cyl.. or if needing DA cyls.. get a cheap OC da log splitter valve ( less than 100$ ), and can get by that way with about 2.85gpm / 1500-1700 psi 3pt pump hyds.. )
pto pump is usually cheaper and easier to setup than a stinger pump.. so no free lunch either way.
if you just needed low flow and temp use.. again.. like a lift wheel on a pull implemnent.. you can chainthe lift and use diverted flow witht he 3pt control for a sa lift cyl.. or if needing DA cyls.. get a cheap OC da log splitter valve ( less than 100$ ), and can get by that way with about 2.85gpm / 1500-1700 psi 3pt pump hyds.. )
OP
mikefinger
New member
Thank you soundguy.
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
let us know how you make out.
OP
mikefinger
New member
Will do, it might be a couple months though. Have to get a few other projects ahead of it.
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
cool. good luck and post back when you get to it.
kenmac
Super Member
- Joined
- Feb 13, 2005
- Messages
- 9,837
- Location
- The Heart of Dixie
- Tractor
- McCormick CX105 Kubota MX 5100 HST, Kubota ZD1021, Kawsaki Mule 4010 trans 4x4
I sure the hydraulics on your TO 30 are better than the hydraulics the TO 20 I once had. I had every old tractor mechanic that I could find try to make my hydraulics better. It didn't work out. Got rid of the TO 20 for better hydraulics. The hydraulics on the tractor I have might not be the best, but they are waaaaaaaaaaaaaay ahead of the TO 20 I once had
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
at best.. the early hyds were 1500-1700 psi and 2.85 gpm.. IF the relief was working, and the piston to cyl seal was good, and the chambers were good...
