JerryG
Super Member
rj,
How long have you had this tractor?
How long have you had this tractor?
Hydraulic problem / questions
- Thread starter rjfoster
- Start date
- Views: 3647
JerryG
Super Member
rj,
How long have you had this tractor?
How long have you had this tractor?
Farwell
Veteran Member
I disconnect the quick connects and join the hoses together, there will be some fluid loss but not much. I keep a bucket handy to catch any loss. Make sure that there is no pressure in the control valve. If yours is like mine I do not think I would mess with the pressure relief valve with out getting all of the possible information before hand. Mine is adjustable and not sure what has to be done to remove mine but if the factory adjustments are changed, I do not know how to reset it to where it should be. Not sure if you have contacted the dealer and talked to their repair guy but this is a good place to start if all else fails. I do it all the time and if they can't help, they tell me who to call to get the information I need.
Good luck.
Farwell
Good luck.
Farwell
Farwell
Veteran Member
I disconnect the quick connects and join the hoses together, there will be some fluid loss but not much. I keep a bucket handy to catch any loss. Make sure that there is no pressure in the control valve. If yours is like mine I do not think I would mess with the pressure relief valve with out getting all of the possible information before hand. Mine is adjustable and not sure what has to be done to remove mine but if the factory adjustments are changed, I do not know how to reset it to where it should be. Not sure if you have contacted the dealer and talked to their repair guy but this is a good place to start if all else fails. I do it all the time and if they can't help, they tell me who to call to get the information I need.
Good luck.
Farwell
Good luck.
Farwell
<font color="blue">Most tractors wil have 2 relief valves. The first is the system relief and it is located near the 3pt. The other is in the loader valve itself. It would be a cartridge that just unscrews.
</font>
Mad,
Do you think I could have a relief valve problem? I have a similar problem has this one I posted here:Loader Problem
I beleive I found and checked the relief valve on the manifold block, but I have figured out where it might be on the control valve. The CV is a Diesel Kiki that I cannot locate any info for.
Thanks!
</font>
Mad,
Do you think I could have a relief valve problem? I have a similar problem has this one I posted here:Loader Problem
I beleive I found and checked the relief valve on the manifold block, but I have figured out where it might be on the control valve. The CV is a Diesel Kiki that I cannot locate any info for.
Thanks!
<font color="blue">Most tractors wil have 2 relief valves. The first is the system relief and it is located near the 3pt. The other is in the loader valve itself. It would be a cartridge that just unscrews.
</font>
Mad,
Do you think I could have a relief valve problem? I have a similar problem has this one I posted here:Loader Problem
I beleive I found and checked the relief valve on the manifold block, but I have figured out where it might be on the control valve. The CV is a Diesel Kiki that I cannot locate any info for.
Thanks!
</font>
Mad,
Do you think I could have a relief valve problem? I have a similar problem has this one I posted here:Loader Problem
I beleive I found and checked the relief valve on the manifold block, but I have figured out where it might be on the control valve. The CV is a Diesel Kiki that I cannot locate any info for.
Thanks!
I was able to figure out where the relief valve was located- removed it and looked at the internal aspects of it. No blockages, etc.....
Did pay a little more attention to what is going on regarding the problem:
-curl up is unable to lift a load and is slow without a load
-upward movement of the entire bucket with a load does not move easily, while without a load it is fine
I am thinking that the pump will have to be removed and taken in for evaluation. Any other suggestions that I should try?
Did pay a little more attention to what is going on regarding the problem:
-curl up is unable to lift a load and is slow without a load
-upward movement of the entire bucket with a load does not move easily, while without a load it is fine
I am thinking that the pump will have to be removed and taken in for evaluation. Any other suggestions that I should try?
I was able to figure out where the relief valve was located- removed it and looked at the internal aspects of it. No blockages, etc.....
Did pay a little more attention to what is going on regarding the problem:
-curl up is unable to lift a load and is slow without a load
-upward movement of the entire bucket with a load does not move easily, while without a load it is fine
I am thinking that the pump will have to be removed and taken in for evaluation. Any other suggestions that I should try?
Did pay a little more attention to what is going on regarding the problem:
-curl up is unable to lift a load and is slow without a load
-upward movement of the entire bucket with a load does not move easily, while without a load it is fine
I am thinking that the pump will have to be removed and taken in for evaluation. Any other suggestions that I should try?
