iMatch Bushings - online source

   / iMatch Bushings - online source #1  

TOL1488

Silver Member
Joined
Aug 16, 2005
Messages
136
Location
LA
Tractor
JD 2520
Anyone find an online source for IMatch bushings?

$16.95 each is a bit high for a $3.00 (on the high end) part. /forums/images/graemlins/mad.gif

I don't think I need the special metal the JD ones are made from.
 
   / iMatch Bushings - online source #2  
Yep, I'd go with the $3 bushing too.
 
   / iMatch Bushings - online source #3  
I went to the local Farm and Fleet and picked up a pair of bushings for less than $3.

I asked the salesman who sold me my iMatch if I should purchase an extra set and he said something like, check the price before you do that. My point being, even a Deere dealer wasn't pushing them (and that was good advice)
 
   / iMatch Bushings - online source #4  
The bushings sold for the iMatch-type conversion have a step, and roll pins to hold them on. See attached. Doubt you found those for $3. These are from SpeeCo for around $15. From Deere, they are in a kit that also includes the top link bushing. To fit right, buy the Cat I-III, not the Cat II-III 'bushing'.
 

Attachments

  • 881998-bushings.jpg
    881998-bushings.jpg
    12.5 KB · Views: 1,032
   / iMatch Bushings - online source #5  
If these are the bushings you guys are talking about, they are $21.95 a pair with the roll pins at most TSC stores. They look exactly the same as the pair that came with the I-match from Deere.

Iowa2210
 
   / iMatch Bushings - online source #6  
The bushings from Farm and Fleet that I bought were Cat2-3 and I still had to buy a cat1-2 sleeve. Price was $17.95.
 
   / iMatch Bushings - online source #7  
FF was where I bought mine, and I had to wait for them to finally get the right ones (Cat 1-3) in before I'd buy them. They were from SpeeCo, part # HF141144 and cost me $12.99 at the time.
 
   / iMatch Bushings - online source
  • Thread Starter
#8  
The bushings zip tied to my Imatch when it arrived were nothing more than 1 1/4" long x 1 7/16 OD x 7/8 ID hardened steel bushings. I wonder why they changed the bushings?

For something with a machined shoulder and drilled holes I can understand a bit of a price increase. I'll likely find someplace online to purchase the SpeeCo kit.
 
   / iMatch Bushings - online source #9  
Does anyone have either the JD or the Speeco part number for the part that Beenthare posted an image of?
I don't want to mess around with bushings (metal tube adapters) and their narrow size and the clip that keep this bushing from falling off.
 
   / iMatch Bushings - online source #10  
I (beenthere) posted the SpeeCo number for the image. /forums/images/graemlins/wink.gif

SpeeCo, part # HF141144
 

Tractor & Equipment Auctions

2008 Ford F-450 4x4 Crew Cab CM Service Truck (A49461)
2008 Ford F-450...
2015 JEEP PATRIOT (A51406)
2015 JEEP PATRIOT...
2006 IC PB30500 School Bus (A50323)
2006 IC PB30500...
https://www.accessnewswire.com/newsroom/en/healthcare-and-pharmaceutical/slimjaro-vs-burnjaro-reviews-a-comprehensive-analysis-of-benefits-and-1044755
https://www.accessn...
Pallet Fees (A50775)
Pallet Fees (A50775)
BANDIT ZT1844 RUBBER TRACK STUMP GRINDER (A50458)
BANDIT ZT1844...
 
Top