Johne deere 420 loader cylinder rebuild
- Thread starter jcavazos50
- Start date
- Views: 15641
-
- Tags
- john deere 420
beenthere
Super Star Member
- Joined
- Aug 16, 2001
- Messages
- 18,467
- Location
- Southern Wisconsin, USA
- Tractor
- JD_4x2_Gator, JD_4300, JD_425, JD_455 AWS, added JD_455, JD_110, JD_X485(sold)
:welcome: to TBN
Now that you have two threads started, which one to respond to.. ??
Have you looked at the parts breakdown like seen on jdparts.com? It's a good place to see what parts need to be removed and if you have a snap ring or a spring wire holding it together. You will need to track the right one down with the serial number of the 420 FEL.
Good help will be forthcoming.. we can help you get it done. What is the problem that you think the cylinders need rebuilt?
And the lift or the bucket curl, or both sets?
Now that you have two threads started, which one to respond to.. ??
Have you looked at the parts breakdown like seen on jdparts.com? It's a good place to see what parts need to be removed and if you have a snap ring or a spring wire holding it together. You will need to track the right one down with the serial number of the 420 FEL.
Good help will be forthcoming.. we can help you get it done. What is the problem that you think the cylinders need rebuilt?
And the lift or the bucket curl, or both sets?
OP
jcavazos50
New member
Thank you for replying. Its a snap ring holding it together. The rebuild kit i found is AH176283 and its both sets that are leaking fluild pretty bad
OP
jcavazos50
New member
OP
jcavazos50
New member
You can see in the picture it been leaking for a while slowly but just recently its gotten pretty bad
kennyd
Advertiser
See if this thread helps: http://www.tractorbynet.com/forums/hydraulics/122281-jd-hydraulic-cylinder-rebuild-help.html
tdavis7057
New member
- Joined
- Sep 20, 2018
- Messages
- 5
- Tractor
- 2004 Johndeere 4310
Re: Johne deere 300 loader cylinder reuild
I知 looking for information on 300x loader cylinder rebuild instead.
I知 looking for information on 300x loader cylinder rebuild instead.
beenthere
Super Star Member
- Joined
- Aug 16, 2001
- Messages
- 18,467
- Location
- Southern Wisconsin, USA
- Tractor
- JD_4x2_Gator, JD_4300, JD_425, JD_455 AWS, added JD_455, JD_110, JD_X485(sold)
Remove cylinder.
Get seal kit.
Remove outer snap ring.
Push cylinder guide back into the barrel about 1 inch to expose a snap ring groove on inside of the barrel.
In the seal kit find an orange ring that needs to be inserted into the groove in the barrel. The groove is contoured, so be sure to install ring proper way.
Then pull cylinder rod and guide from barrel. The orange ring allows second snap ring on guide to slip past the snap ring groove.
Then remove nut from rod, remove piston and guide from rod. replace seals and orings on guide and piston. and reassemble. The orange ring is not used for reassembly, it is used for disassembly only.
Get seal kit.
Remove outer snap ring.
Push cylinder guide back into the barrel about 1 inch to expose a snap ring groove on inside of the barrel.
In the seal kit find an orange ring that needs to be inserted into the groove in the barrel. The groove is contoured, so be sure to install ring proper way.
Then pull cylinder rod and guide from barrel. The orange ring allows second snap ring on guide to slip past the snap ring groove.
Then remove nut from rod, remove piston and guide from rod. replace seals and orings on guide and piston. and reassemble. The orange ring is not used for reassembly, it is used for disassembly only.
