loader bar and teeth

[lilranch2001]

I ordered this for my CT 235, has anyone installed one? I havent seen it yet, so Im not sure what it is going to take to install it.

 

[CT230 Fan]

Was there supposed to be a link or a picture?

 

[galaxie428]

I am not sure about the loader bar but I bought individual teeth for my bucket and it take about 10 min or less to install them in the predrilled bucket holes.

 

[crusty 1]

I have zero knowledge about the bucket teeth,what is the main use of them?I don,t know if I need them or not.

 

[Gittyup]

If you are talking about a toothbar for a loader bucket, they are great. Mine goes on/off with just two bolts, one at each end of the bucket. It makes digging into either fresh ground or a pile, much more efficient and it proctects your loader cutting edge too. Highly recommend if doing a lot of digging.

 

[crusty 1]

only dig holes to bury any left over money,if I keep buyind no more need to dig holes!:laughing:

 

[lilranch2001]

I havent seen one yet so I am not sure what it looks like and cannot post a picture.
Havent been able to find it on Bobcats website either.

I dont think there is any holes in my loader bucket, I guess I will just wait till I get it in next week

 

[crusty 1]

lil ranch,how many hours have put on your cat? Had any problems?

 

[lilranch2001]

8 hours so far, dug and moved a hellava lot of clay out of a bank outside my walk out basement that I want to build a retaining wall in, cleaned up a lot of dead logs along the edge of my woods, broke my 4 wheel drive knob by stepping on it, and got her stuck to the frame, its been a good week :laughing:
On a good note, I have started to design a new handle for the 4 wheel drive knob today. When I finish it, and IF IT WORKS WELL, I will post a picture. I know I want something different than what Bobcat has, I will step on it again if I put a new knob on it.

 

[wallace]

Lookig for something like this?

 

[qed-cat225]

where did you get the teeth from? I have been looking for them instead of buying the tooth bar from wrlong

 

[crusty 1]

Darn this sight I thought I alresdy had everthing I needed,now a toothbar.Whats that going to set a guy back? Oh well it,s only the kids inhieristment I,m spending,instesd of creamation they may just throw me on a pile of burning tires:laughing:

 

[qed-cat225]

last year mine was 279 plus shipping for the 68" bucket on the 7TL loader

 

[deansdad]

......I thought I alresdy had everthing I needed,now a toothbar.
Whats that going to set a guy back? Oh well it,s only the kids inhieristment

Doesn't matter how much....absolute BEST "bang for your (your kids) buck" you can possibly get. (Well, except maybe for a nice set of pallet forks, or, a sturdy boxblade, or a mean grapple, or TNT, or, or, or....<g>).

Toothbar lets you actually "dig" with the FEL (in anything more than a loose pile of sand) and at the same time protects the bucket. Do go for the - slips over the cutting edge, 2 bolt attach type.

 

[Gittyup]

Yes, expect to pay aroung $300 for it. It's seems like a lot for what it is, but it's worth it.

 

[wallace]

I'd be happy to quote anyone out one, I just need the inside bucket measurement.

 

[qed-cat225]

67-1/2" inches for the 68" pin on loader, or you can get the bolt on teeth from bobcat for around this: 6728247 bucket teeth with hardware $17.18 typ 6 or 7 teeth