Mods for my LS 232

   / Mods for my LS 232 #1  

tuffytractor

New member
Joined
Dec 7, 2013
Messages
6
Location
United States
Tractor
LS 232H Premium
Finally, I got all the planned Mods for my 232H Premium complete.
Raised the seat up.
Two rear remotes.
Top & Tilt.
3 X Multiplier.
3rd function up front for the grapple.
E0769611-AF50-4560-B3AC-71AFD88AB715_1_105_c.jpeg

35397A5C-0D89-451C-82C8-6E526E9C59C1_1_105_c.jpeg


A52ED2CD-DE5D-41CB-A388-F128D90569B5_1_105_c.jpeg
1CAC8C9E-DE60-492A-A533-B74AF6C2722F_1_105_c.jpeg
435B52AC-6E5B-4079-82D6-F6906889003C_1_105_c.jpeg
34470859-8461-4D23-BF77-6B972A8F7D2C_1_105_c.jpeg
66D68F5E-4042-4134-832A-3D54FAB8DCC7_1_105_c.jpeg
03E389B7-554F-4132-8C3E-F0F1D69C4AD7_1_105_c.jpeg
3629863E-B0DF-4CD3-8771-26AFE3CCF28F_1_105_c.jpeg
 
   / Mods for my LS 232 #2  
That's a pretty good idea how to raise the seat, I'll have to keep that in mind.
 
   / Mods for my LS 232 #3  
What 3rd function kit did you go with and what grapple... I'm getting ready to pull the trigger but the cost for the 3rd function kit has my eyebrows curled.
 
   / Mods for my LS 232
  • Thread Starter
#4  
That's a pretty good idea how to raise the seat, I'll have to keep that in mind.
I first identified the metric bolt, then went and bought the longest metric bolt I could and sized the aluminum sleeve to be a tight fit. Using the long bolt, I had to loosen other seat brackets to get it in place. I used a stop on my chop saw to make sure all the spacers were the same length. I thought it would be impossible to get all four bolts simultaneously, so I used O-rings on the bolt to hold the washer, spacer, and bolts in place while lifting the seat into position. The O-ring trick worked fairly well.
 
   / Mods for my LS 232
  • Thread Starter
#5  
What 3rd function kit did you go with and what grapple... I'm getting ready to pull the trigger but the cost for the 3rd function kit has my eyebrows curled.
$300 part #40546530 for the LS 232 premium, I don't know if it is the same part number for whatever tractor you may have. Kit includes hard lines and quick connects on both ends. The grapple is from LS as well, MCG1154A, 54" rake grapple.

I used the LS parts finder to find which kit part# I needed then had the dealer confirm it was correct.

http://lspo.lsmtron.com/PartsList/wpc2000_MAIN.aspx
though the URL says it is not secure.
 
   / Mods for my LS 232 #6  
Good job with the modifications, particularly with the seat height. What a creative way to lift it.
 

Tractor & Equipment Auctions

2019 ALLMAND LIGHT TOWER(INOPERABLE) (A47001)
2019 ALLMAND LIGHT...
2008 Hino 268A (A45336)
2008 Hino 268A...
2016 Isuzu NPR-HD Morgan 24ft Box Truck (A44571)
2016 Isuzu NPR-HD...
2010 UTILITY 53X102 DRY VAN TRAILER (A45677)
2010 UTILITY...
Air Compressor (A46683)
Air Compressor...
2015 Dodge Charger (A46684)
2015 Dodge Charger...
 
Top