New to me 2210d

[bmaverick]

Looks like damn near the same hog if not THE same....

International Technologies?

IT is still around to a degree. Another company bought them out, they still have old stock on the shelves out in California. I have a post hole auger imported by them. If it wasn't for the expensive sipping, I would have ordered the OE cutters and the tip from them. This goes back 4 years though.

 

[Smokeonthewater]

Well I finally remembered to check this today.... the knob is very hard to turn w a load (5' hog) lifted but I closed it all the way, opened 1/4 turn, lifted, then closed it as I killed the engine....
The hog stopped lowering as soon as it closed and stayed there till I opened the valve again.... Safe to say the issue is not the cylinder... what's next?

Edit... here's what's in my manual...
First two ruled out....

 

[Smokeonthewater]

I did get my new ign switch installed today and magically my 'clutch' issues are gone... LOL

 

[bmaverick]

Well I finally remembered to check this today.... the knob is very hard to turn w a load (5' hog) lifted but I closed it all the way, opened 1/4 turn, lifted, then closed it as I killed the engine....
The hog stopped lowering as soon as it closed and stayed there till I opened the valve again.... Safe to say the issue is not the cylinder... what's next?

Edit... here's what's in my manual...
First two ruled out....

View attachment 697894

What about a clogged vent tube? This is the funny U-hook tube out the back. I also use it as a linch pin holder when switching attachments.

 

[careyo63]

Mine won't stay up either unless I lock it. I had trouble with the linkage to the valve. So much play in it the height would move. I was able to correct that as long as the tractor is running. Which for me is very seldom do I even have to use it. YM2000 vent which appeared to be clogged by Dirt Dobbers. Never the less It was clogged just unscrewed it.

Attachments

• 
  Picture 023.jpg

  183.3 KB · Views: 267

 

[Smokeonthewater]

What do you guys think of this....
Hydraulic oil coming out past the pto shifter while driving... pto engagement status doesn't matter...
Fill level is perfect according to the dipstick...

 

[careyo63]

I used a o-ring around the bottom of the rubber boot. Worked for me. Mine is in better shape and not power shift causing a problem but it's worth a try.

Attachments

• 
  Picture 030.jpg

  976.1 KB · Views: 329

 

[winston1]

Is this o-ring missing? O-RING
#4 on drawing

 

[Smokeonthewater]

Hmmm dunno... will check

Is that supposed to go over the boot?
Is it normal to have oil in the boot?

 

[California]

Is it normal to have oil in the boot?

Oily, but not fluid.

I bought a new boot for the YM240 long ago and haven't seen oil externally, since.

 

[winston1]

Don't know whether under or over?? Have you made sure your transmission vent is open? (On top of the rockshaft)

 

[Smokeonthewater]

Need to... guess I'll walk over there now....

 

[Smokeonthewater]

Well good news and bad news.... it's open but it's also too open...

 

[winston1]

Not positive but I think 1/8" pipe threads might work in that. Or AXLE BREATHER (VENT) TUBE_

 

[Smokeonthewater]

At some point I'll work on getting the old one out n go from there.... kinda hope it's threaded as that might be easier to remove..... unless it's harder lol

 

[California]

At some point I'll work on getting the old one out n go from there.... kinda hope it's threaded as that might be easier to remove..... unless it's harder lol

It's threaded. And an easy-out should remove that ... easily!

See if Hoye has the replacement. It's common to replace them. People think they can attach a tow rope there. Nope.

I was lucky. That part and several similar trivial parts were available for my YM240 when I bought and renovated it. The local VN importer would salvage anything I needed, off the warranty returns that he had parked out back.

 

[Smokeonthewater]

Good deal... winston was kind enough to link the replacement above

 

[careyo63]

The tube is Part# AB-42280 Repl. #1941150.42280 to many models to list apparently. Fredricks has a few 1000 I'm sure.

 

[Smokeonthewater]

...