BXpanded
Silver Member, Approved Advertiser
We can accommodate the bolt on edge. We just have to know about it in advance.
Harry
BXpanded
Harry
BXpanded
Tooth bar for Kioti 72" bucket?
- Thread starter MinnesotaEric
- Start date
- Views: 13589
OP
MinnesotaEric
Super Member
Exactly. I ordered the bolt on bar that is added to the existing bucket and am wondering if anybody has gotten a bolt in tooth bar that fits over everything.
Thanks!
k0ua
Epic Contributor
Well it looks like BXxpanded will make a piranha for you.
OP
MinnesotaEric
Super Member
FWIW, now that I have the tractor, i can answer my own question for the next guy who is looking. The 72" bucket measures exactly 72" inside edge to inside edge.
Now I can order a tooth bar.
Now I can order a tooth bar.
grm61
Platinum Member
Eric, you may want to weld those outside edges of the cutting edge to the bucket, or drill another hole at the ends.
I took me 2 hours to tweek mine on the end after bolting it on.:mur:
After that, I welded the outside edges, and then about a one and a half inch bead in between each bolt hole, quite a bit of leverage out there.
It will take a little grinding to get it off.
Nice tractor:thumbsup:
I took me 2 hours to tweek mine on the end after bolting it on.:mur:
After that, I welded the outside edges, and then about a one and a half inch bead in between each bolt hole, quite a bit of leverage out there.
It will take a little grinding to get it off.
Nice tractor:thumbsup:
boggen
Elite Member
- Joined
- Feb 22, 2011
- Messages
- 3,829
- Location
- Trivoli, IL
- Tractor
- SSTT (Sideways Snake Tain Tractor) and STB (sideways train box) tractor, dirt harvester
i remember seeing a "strap on" tooth bar.
i like "back dragging" with a straight edge on the FEL bucket for both snow clearing, and simply leveling out a spot to filling in ruts/holes in road. and then tooth edge for bucket for digging with the FEL.
i like "back dragging" with a straight edge on the FEL bucket for both snow clearing, and simply leveling out a spot to filling in ruts/holes in road. and then tooth edge for bucket for digging with the FEL.
OP
MinnesotaEric
Super Member
The ends can bend? That wasn't on my radar and so i'll take your advice to heart.
grm61
Platinum Member
Yep, I was horsing mine a bit, slowly driving ahead while curling the bucket rolling some boulders up out of the ground, no support on the ends, had to C clamp it up and weld it, all is good now.
Threepoint
Veteran Member
- Joined
- Feb 13, 2014
- Messages
- 2,244
- Location
- No. VA
- Tractor
- Kubota B2150HST w/ LA350 loader, Kubota GF1800 HST, Kioti CK3510SE HST w/ KL4030 loader, Kioti NX4510HST/cab w/ KL6010 loader
Eric, congratulations on the new arrival. Looks like it was worth the wait! I have the same loader and bucket, but without the bolt-on HD edge. I added a 72" Tisco tooth bar and like it a lot. With the HD edge, suggest you call or email Tisco customer service in Oakdale, MN to ask if it would work w/o modification. If so, the TB bolts to the sides of the bucket, so should do double-duty to help with the bending that grm61 describes.
OP
MinnesotaEric
Super Member
Today i could not locally locate 1-1/4" by X D-ring clevis and so I ordered one from Agri supply for use as a tie-down down on the tow-bar.
I also mounted my now orange CAT 2 Quick Hitch.
I also mounted my now orange CAT 2 Quick Hitch.
