Search results

Ya know I would have never thought I would ever have to worry about a air hose being UV resistant until I mounted a air hose reel where the sun shines and the hose that is on it is going by the way side fast. What is a good UV resistant hose? Brands are welcome I don't care who makes it or what...

Has anybody ever had an Eaton Compressor? If so what are your thoughts on the unit? I am finally going to upgrade from a small compressor to a 80gal 7.5hp single phase and Eaton is at the top of my list. This project will require the use of my tractor to unload the compressor from my trailer and...

This is what my little Jack Russell treed today behind my shop. I figure @ 40lbs, I was @ 15-20yds away takin the pictures right beside my PHD stand.

To my shop awning:) I had 15' now I have 25', I should have done 20 to start with but as all you know you always go too small to start with. No more water in FEL when it rains. More room for more toys:)

I noticed the other night the idiot light for the charging system was on dim, it was dark out so that's how I could see it otherwise you couldn't tell during the daylight hrs.... and I thought ok it has to be one of two things...regulator or alternator so I hooked up a volt meter to it and it...

I am in the process of building a 4X8 dump trailer for using around the place, I have no plans to put it on the road. I started this project in December with the purchase of a "parts" trailer and have just worked from there for what I needed. The local metal dealer, E bay and metal already on...

I had 171lbs on the ft. and need to add more weight to my little 15hp Mitsubishi so I went to my metal place and found a small pallet of lead and the perfect container to put it in. A 4" square 1/4" wall tube almost 33" long. I capped off one end of the tube and used my torch to melt the lead...

If anybody is interested in what their L2800/3400 sight guage looks like here are a couple of picts and the threads look cracked causing my leak, I am waiting on the new one to be shipped to me and no I have no idea how much it cost. I have 200hrs on my tractor and it was time for all the...

Since I recently purchased a new tiller and all that good happy stuff, the new tiller needed a good stand when not in use and to be easily manuvered when hooking & unhooking up easily....here is what I put together. I used 5" casters, 1 1/8X1/8 tubing and some other 1/8 and 3/16 angles & flats...

I finally got a tiller after five years of wanting one....It is an Agric CM 45 from CCM, I ordered it on Wednesday and picked it up on Friday at the shipping terminal, the tiller was 1150.00 and shipping was 150.00. I am gonna run it behind my little 15hp Mistubishi, I tested it out on...

Gentelmen I have someone looking for a powersteering pump kit for a Massey Fergerson model 85 tractor, 59 or 60 year model with Conteninel Diesel eng.

I finally got around to installing bucket hooks on my L2800. I first reinforced the upper lip with a stick of 2 3/8 X 3/16" drill stem pipe under the lip. Then attached the hooks to the brackets which are 5/16" thick then welded them to the bucket after grinding a little angle int them so my...

What are the possible reasons this 3pt maybe leaking down from full up to full down in about 1min.

I figured since it is a Kubota then this is the right spot. Well here is my story. Today I stuck my tractor in my back pond...well not in the pond but close enough. I decided that since it was so low that I would get a few scoops of dirt/mud and place them close by in a few low spots. I went in...

I was changing the oil in my truck and found another good use for QA forks.

I did not know that Fire Ants had any natural enemys (besides us and some imported fly) but I have seen many Pharaoh ant (aka sugar ant) beds with many Fire Ant remmants piled up around them. It looks like the Fire Ants had their hats handed to them. Here is some Photos.

I built this disk with the aid (drawings) of another TBN member MOEMOE, I did have to improvise and added my own custom touch. Here is the metal laid out.

Can anybody tell what brand this one is.

Their first models were altered EZ-GO units.

My first welding project. It took me week to build this stand and it works great. I had to purchase 2" 3/16 angle and 6 2" swivel casters, I already had the other materials laying around.

Anybody use one of these and are they any comparison to a tiller or disk.

I will soon be a proud new owner of a L2800, LA463 loader with detachable bucket and the 48" skid steer forks, BH75 BH and it's all y'alls fault . I was going to get the B3030 but after my dealer showed me the L2800 and test driving both machines I will be getting the L2800. The one thing I...