Search results

I've got an 06' L2800hst that I bought new. It has 400 hours on it that has been used 95% for mowing grass with a rear finish mower. I also have the FEL and backhoe with subframe on in. FEL might have 20 hours on it and the hoe, 10hrs at the most. Its all well maintained and barn stored...

I'm trying to help out my mother in law with problem with the ML108H FEL on her Mahindra 2810 HST. Her husband has recently passed and to make a long story short, nephew may have jacked up the loader somehow. As you can see from the pic, the far cylinder rod that operates the curl function is...

I'm trying to help out my mother in law with problem with the ML108H FEL on her Mahindra 2810 HST. Her husband has recently passed and to make a long story short, nephew may have jacked up the loader somehow. As you can see from the pic, the far cylinder rod that operates the curl function is...

So my father in law has a 2004 2810 HST. He has a blown head gasket and there are no local dealers around anymore. He's wanting to tear into the job himself, but is having trouble finding a service manual. Are there any out there for this model?

I'm looking for some type of electric tomato strainer to process tomatoes for canning. I've got the standard hand crank type juicer, but would like to speed up the process. I've found a couple imported from Italy. It just seems there isn't much to choose from. A Spremy and OMRA model and...

I planted my potatoes on Good Friday, like grandma said to do. Most of them are up and we got hit with a good frost the past two nights. Will they continue to sprout, or am I going to have to replant them all? all of the leaves are dead. This is only my second year growing potatoes in the...

I've got a L2800 with BH75 hoe. My cousin needs about 60-70' of waterline laid at his new house. He has a 16' stock trailer and my TLB will not fit. However, if I remove the loader it will fit. Would you all see any problems in digging this little bit of a trench without the FEL on the...

I want to get my dad a GPS. He needs one that will work on road trips and a hunting trip into the Colorado mountains. I thought I would kill two birds with one stone if I could find a handheld unit that also routes will on the highway, but I want it to have the voice feature while giving...

Unfortunatly, my sister is getting a divorce. They have a 2004 model 4110 HST(20hp,17PTO) with loader, 60" belly mower with 175 hrs. They also have a lightly used JD 4ft rotary cutter and 4ft rear blade. What would be the ballpark worth of this package? I went to tractorhouse.com and I'm...

I figure this is the time of the year when places will try to start moving them. I'm up in the air as to tractor vs stand alone. I like the speed of the stand alones, but I am kind of leaning towards tractor mounted since I only put 50-60 hrs a year on my tractor. I have a Kubota L2800 that...

I've got a new half ton pickup with 1100 miles on it. I checked the oil today and it was a hair over a half quart low. Is this normal with a new truck? This is my first new one in 12 yrs. I think the salesman did say it may use a little oil up to the first oil change.

Did anyone's garden get wiped out by the heavy frost we had in the Ohio region last night? My corn just came through a couple of days ago and it looks Ok so far. Really, the only thing that looks bad are a few of my tomato plants and the zuchini plants.

I know it fits the 7800, but I'm not sure about the 3200. Can the hoe work in tandem with a MMM on the 3200? Do the lift arms need to be removed when attaching the hoe? Thinking about trading my L2800 in. I get tired of having to remove my mower everytime I want to dig a hole.

What is going on here in the Mahindra Buying/Pricing forum? The activity seems to have dropped way off in the past few months. No new posts in the buying/pricing section for 6 days and the biggest thread since the first of the year was regarding Mahindra trucks. I know this has been the slow...

I installed a Brunco 150 woodburning furnace and a 18' Metalbestos stack early last fall. What a difference in the electric bill. I heat about 2,600 sq. feet between my basement and main floor. I heat solely with electricity in the past and our average monthly bill used to be around $325 per...

A friend just bought an 07 B7800, 56hrs, FIL, and 60" deck for $12,000. Wow what a deal. Anyway he wants to be able to hook his 3pt log splitter up to the tractor. My thinking was to just have him get the hydraulic hook up kit for the BH75 hoe and install that kit. He could then just have...

Anyone have any idea what this might score. I know nothing of scoring. I've been told maybe 150 class. Has to be 160 to make Ohio Big Buck club, and I don't think it will go that far. It has some small points that can't be seen it the pics. There are 10 on one side and 5 on the other, the...

I'm taking my first crack at making wine. I've got 3 - 5gal buckets of plums. How much wine would this make? I've got 2 - 6 gal carbouys to work with and can get more if needed. Here is how I was told to do it, short version. Smash plums, cover and let sit for 10 days. Put 3 gal on juice...

I have been seeing alot of big discounts and rebates among some of the lesser known brands. Should this be considered good or bad for the perspective buyer? With the economy slump and with the way things are in the middle east, the economy could go further south in a matter of weeks. I just...

This one weighed 53lbs. :)

Thought I'd share my weekend catch. These are what I fish for exclusively and I caught this 57 pounder on my first trip out on Sunday night. I turned it loose after the photo op.

What does the label I see on diesel pumps mean that says something like "not for use in 2007 model vehicles or later"? Does this mean 2007 and under? What does it mean?

I've got a 1303 tiller and she has been good to me. Has anyone ever removed the middle board in the rear of the tiller to make a nice hill? Atleast that is what it looks like it would do if I took out the center piece. I'm planting some potatoes this year and I thought I would try it out...

Please look at the pics below. It appears that the dipper cylinder runs up the boom slightly off center. Especially when you look at the V shaped plate under the rod. Also, see the 2 shims at the top with the arrows. Does everyone have a shim on each side? The reason I ask: In the second...

My father in law asked me to inquire about putting stronger lift cylinders on the loader for his 2810 HST (factory loader). I read in another post, that I can not find right now, that this can be done. Are there any dealers that can give me any info? If he can get stronger cylinders, how much...

Has anyone devised a method for storing their backhoe on some kind of dolly system where it can be wheeled around easily? Since I have the BH75 hoe, I'm now looking to make the most of my floor space in my garage as it is getting quite crowded. I'm try to store the tractor/loader/RFM/Hoe/Honda...

How exactly does it attach? I'm thinking of getting one for my 2800. What all is involved in installing and removing the hoe? I have a finish mower that I use to mow my grass with. Do the lower 3pt hitch arms have to be removed? Does the subframe mount have to be removed to put the 3pt...

B2620, 364 loader, 60" MMM, 50" Landpride Reverse tine tiller, loaded R4s - $17,232 Tractor loader and mower with loaded R4s - 15,800 Tiller - 1,432 This is not for me, but for my brother in law. I'm kind of helping him with the differences in tractor brands. He looked at Mahindra and Deere...

I'm thinking of getting my F-I-L a Markham toothbar for his 2810 HST. He has the Mahindra loader that came with this tractor. Could someone give me an exact measurement of the inside dimension of the bucket on the loader? The measurement has to be taken about 5" back from the cutting edge. I...

Could someone post a couple of pics of the rear end of their 2615 for me?

I have a .5 HP deep well pump set at 125'. It is pumping water up to the house but won't build any more pressure in the pressure tank than 22lbs. It runs steady at 22lbs and won't kick off. Almost like there is a leak in the line somewhere. Can a pump go bad to where it can lift water 125'...

I just ran to the local fuel station that carries the off-road diesel because I had heard they were about out. I bought all they had left at $3.50 gallon. I ended up getting 47 gallons in a 55 gallon blue poly drum. I should have it used up by Oct. - November. The drum is in my unheated...

I have read through countless saw threads and I've narrowed it down to a few models that my local dealer has: Husky 350 - $340 Husky 455 - $395 Echo c520 - $390 I'm leaning a little towards the Echo because of the 5yr warranty but I'm going to check them all out. I'm undecided on an 18 or...

This something I have been wondering about for quite a while. Is engine HP related to the weight of a tractor? Hypothetically speaking could an engine from a B3030 be put in larger tractor like the L3130 and move the tractor around the same? Could a new B2930 engine be put in a L2800 and...

How does this sound: 2415 HST w FEL and 60" MMM - $15,300

I'm wanting to install a wood burner in my basement. It would be a 150,000 btu Brunco or 120,000 btu Woodchuck furnace. I can take my pick as either furnace is going to be given to me. The Woodchuck is only 2 years old, so I would probably go that route. Anyways, I have to get a chimey...

Hi All. I've got a 98' Ford Ranger that won't go into 4wd. It is a vacuum engaged system. The dealership told me it would be one of two things. The switch on the dash or the engaging motor. I replaced the switch on the dash and that didn't fix it. The said the motor ran around $400. I've...

Here is the situation. My dad has a natural gas well on his farm and heats his house with it. We are trying to devise a way of bottling the gas in say a 100lb propane cylinder. The plan is for me to install a vent free natural gas heater in my basement - one of those 30,000 BTU wall mount...

I've had my L2800 with 463 loader for a little over a year now. One of the lift cylinders on the loader is leaking fluid out where the ram moves in and out of the housing. I proably have not more than 10 hrs on the loader. It started leaking about 6 weeks ago and I took it off and in to the...

Anyone now which Woods backhoe best matches up to an L2800? Any one have one and what kind of price might I expect? Thanks.

Is it normal for a dramatic improvement in fuel consumption after break-in? My 2800 has 63 hours on it now and it seems like about 10 hours ago, she started using much less fuel. Thats about when I started adding Diesel KLEEN to the fuel though too. When I first got it last year, it took...

Not tractor related, but what the heck. I have a 97 Force 40 hp 2 stroke. I start and seems to run fine, but is leaking some water in the main case. It is coming from the gasket just under the exaust port cover. If it is just the gasket, I figure it will be an easy fix by removing the gasket...

I just did the 50hr tranny fluid change on my 2800 HST. I jumped the gun at 45 hrs:). I wanted to give SUDT a try. So, I got it changed and mower about 3 acres of grass yesterday. I will say this: the SUDT cut out the HST whine completely in Low range and quieted it down by atleast half in...

I had a new well drilled a few weeks ago. I got the pump set last weekend end, and have been pumping it dry about twice a day ever since to try to get the water to clear up. How long does it generally take for the water to clear up after a new well is drilled? I'm going to give it another...

The loader manual for the LA463 says to "lubricate the joints of the control lever every 10 hours". How do I do this? Do I need to remove the cover under the joystick or remove the rubber boot? I'm at 43 hrs and I've never done this.

My 2800 HST has 43 hrs on it and it has developed a leak somewhere on the loader block. Sometime in the last 5 hrs. I just noticed it today when I saw a few drops oil had accumulated on the garage floor in the time it took me to remove the loader and hook up my mower. The hydraulic block was...

I bought a quick attach over running coupler to put on my L2800. My plan was for the new OC to replace the internal one on the tractor, so I wouldn't have to hear the racheting coming from inside the tractor. I just don't like the racheting noise coming from inside the tractor - I know it is...

I just got my Markham tooth bar. Very nice. The problem is it is 1/4" shorter than it is supposed to be. I realize it is supposed to be 1/4" shorter than the inside dimension, but mine is an additional 1/4" short of that, meaning it is actually 1/2" short. Inside dimension of my bucket is 58...

I bought this single bottom plow and know you guys can help ID it. I know it is a Ford, because I can see the Ford stamp on the back of the moldboard. Thought you guys might know a model #. Its 16". Its in very good shape, almost mint condition with the exeption of a little weatering. No...

Sorry, but I didn't want to hijack someone's thread. I'm going to order a Markham for my 2800 463 loader. The inside dimension is 58 3/8". Will I be alright with the standard amount of teeth or should I have him add 1 or 2 more? I will be doing minor digging and popping out some briars...

I found a nice used 16" one bottom plow for $100. Can my L2800HST 4wd with loaded R4s pull it through unbroken ground? Soil is little clay, not too many rocks. Maybe I should hold out for 12" or 14"? If it is questionable, I will probably pass on it.

Still weighing my water supply options. I have a spring that I have been catching water from and pumping to my house the last couple of years. I just use the water for laundry and flower beds/garden. The spring itself is near the bottom of a 15ft ravene just about 30 ft from my well. There...

For anyone who thinks their water situation is bad... I bought a house and 14 acres a few years ago. Here is my well situation: 85' deep static level 65' 5" casing pump at 74 ft 2 gpm - supposedly So, I have 11 feet of useable water. With the 5" casing, I figure I might have 13 gallons at...

Is there a different type of cab for the Rhino other than the soft vinyl type cab Cabelas offers? I have found one other hard type cab, but it is very expensive. Looking for something less than $1000. Thanks.

Do you guys think my L2800 will pull a set of 2 bottom 12" plows. I think I will have the power, I'm just worried about traction. I have loaded R4s and FE loader. I figure the tractor with loader weighs in at around 4000 lbs. My dads old Ford 600 pulled them fine a couple of years ago when...

What would be the best way to hook up a TSC fender mount radio to an L2800? (Santa brought me one) I know how to mount it, I'm just not sure of the best way to wire it up. I didn't know if I could use the extra wires under the fender? I experimented with hooking up a work light to these...

I was wondering if anyone had the part # for the wheel spacer kit for the L2800. My dealer can't seem to find them and doesn't think they exist. I called TractorSmart and they priced them at $150, but I didn't get the part number.

Does anyone have, or know if you can get telescopic adjusters to replace the turnbuckles on the 2800/3400? Does anyone have them on their 2800/3400? Could you post a pic. If they are available, my only concern would be tire clearance. I have R4s and the turnbuckles only have about an inch...

I was looking at the thread where the guys tractor broke in half(Chinese Forum). Just wondering why the 463 loader on the 2800/3400 has no FEL bracing that runs to the rear axel. Is it an option?

I'm thinking of adding a set of hydraulic ports to my 2800. I may be way off here because I know nothing of hydraulics, but I would like to have something I could plug a future backhoe into. Would I just need a set of ports to do this? Sorry, but I need someone to hold my hand here. I have...

I bought a new L2800 HST about 2 months ago. I have 20 hrs on it now, and probably won't put more than 5 hrs from now until April. I don't anticipate getting to the 50 hr mark until the end of next June anyway. Is it OK to leave the dino oil in her until I reach the 50 hr mark, or should I...

I just got my 2800 back from getting the lift valve replaced. It made a world of difference. However, when I raise the 3pt hitch all the way up, it wants to bog the engine. I think the system is going into relief. I don't think they adjusted the feed back rod on the left lift arm. Do I...

I want to put a couple work lights on my 2800. My quesion is: What are the yellow and black wire for under the turn signal. There is one yellow and one black under each fender with bullet type connections. Is this where I can tie a work light into? I think I have read that these wires are...

I think I may have been bitten by a brown recluse on my cheek. I was putting up a tree stand when I started feeling a warm sensation on my cheek. After 24 hours, the bite developed a back/purple center about 1/4" square. The red swollen area is slightly larger thatn a quarter. The bite looks...

Hi guys, How much length will an over-running clutch add to a PTO shaft? I have a Yanmar tiller and the pto shaft for it is really short. I have replaced my 2210 with a Kubota and the shaft is to short for it. If I could gain 3-4" by adding an OC, that might give me the length I need. I...

I just pulled the engine oil dipstick on my new 2800 HST. First off, it looks nothing like the dipstick shown in the operators manual. It has a small hole in the dipstick about 1/4" from the bottom of the stick. Then, there is another hole further up about 2 1/2" from the bottom of the...

I'm posting this for my father in law. The hydraulics on his 2810 HST have quit working. His loader and 3pt hitch will not raise at all. He has 300 hrs on it. He has contacted his dealer and is going to take it in sometime this week as it is still under warranty. I told him I would ask...

My Kubota LA463 loader is Power Beyond equiped. What exactly is Power Beyond? What are its practical uses? I don't know much about hydraulics. Thanks.

I love this tractor. There are a few things I would change- Throttle is too stiff - It is very hard to bump up the throtte 100rpms at a time. Anyone have a fix for this? 3 pt lift - Mine has the old valve. Dealer is supposed to be filing a complaint for me to get it changed. I am assuming...

I just bougt a L2800 HST. I've been reading the manual on the loader. How do I get it to go to the float position? In the manual, the joystick is all the way forward, but when I do that, it just lifts the tractor off the ground. Also, anyone have any pointers on FEL loader removal. I'm...

USATODAY.com - Reports: Australia's 'Crocodile Hunter' Steve Irwin killed

I picked up my new tractor yesterday. I will have to post some pics later. I like it a lot. I spent yesterday afternoon loading the rears with wiper fluid. About 32-35 gallons per tire is my guess. I thought I would finally get some sleep after I got her here at the house, but here it is...

Is the grill guard extra, or does it have to be installed along with the LA463 loader on a L2800? My dealer has to put the loader on and I don't want to get shorted on something.

L2800HST LA463 Loader R4's $15,000 The serial number of the tractor is 54090. Can someone tell me if this has the updated 3pt valve? The dealer is going to check into it, but said he has never heard of it. Said he would fix it if it was covered under warranty. Please !! If someone could...

Anyone know the serial number of the L2800HST where they started replacing the 3pt lift valve?

Just got off the phone with a local dealer. Here is the price he gave me. L2800HST R4's LA463 loader Wheel spacers for rear - said he recommended them so hitch arms don't hit on the R4's $15,600 This was thru phone conversation, so I might be able to do a little better in person. What do...

I'm in the market for a new tractor. I'm looking for something in the 28-30 HP range. 4wd with HST and loader. I don't want to spend anymore than 16,000. Does John Deere have something that falls into this category? I don't want a 790. Thanks.

I got my Yanmar sold, so now I am ready to get serious in my search for a tractor. I'm going to start by looking at the L2800HST. I'm just wondering about power. I have heard guys complain that the 2800HST might be a little underpowered, especially with having a front end loader on and loaded...

Can anyone give me an appoximate number of 2810's that were sold here in the US during there run with Mahindra? My father in law has one and loves it, he wanted me to see if I could find out. Don't ask me why, cause I don't know. I read on here that Mahindra moves approx. 12,000-15,000...

Who is next in line in market share after the Big 3 as far as compacts are concerned? Judging from the number of posts on TBN, it looks like Kioti, then Mahindra. Anyone have an opinion or facts on this? I don't want to buy from a manufacturer that will not be around in 20 years. Thanks.

Are there any 2815HST owners on here? I've searched and can't find anyone who has bought a 2815 and have only found 1 or 2 posts from people who have bought a 3215 HST. Dealers - Are you guys selling many of the 2815s? I looked at this tractor a couple of weeks ago and I like it, but would...

I'd like to list my 2210D on ebay. I have listed it locally, on equipment trader, and various other internet classified listing locations. I haven't got any interest in it at all. Has anyone every sold there Yanmar on Ebay? Are there ways to get around their anti grey policies? On another...

I'm looking at the specs on both tractors. I would use both for about 80% finish mowing. The L2800HST has 22.5 pto HP @2800 RPMs while the Mahindra generates 22 pto HP @ 2376 RPMs. Does that mean the Mahindra has a stronger engine? Does that mean I would have to run the Kubota at 2800 RPMs...

Does Kubota charge more for the R4's or is it a dealer specific thing? My local dealer has a 2800 I'm looking at, but it has Ag's on it. While I have to pay more for the R4's or does Kubota give you a choice at no extra charge? Thanks guys.

Hi, It is my understanding that some of the older 7000 series tractors were made by Mitsubishi. Now Mahindra has since picked up the old Mitsubishi/Cub line in their 15 series. I was just wondering if you guys with the 7000 series tractors were happy with them. How many hours do you have on...

Is there a consensus on who makes the most reliable engines for CUT's or does brand loyalty come into play? For example, I've read in a couple of forums where Mitsubushi knows diesels, but there are more reliable diesels out there.

Hi, I am in the market for a new tractor and just forgot about Massey. The 1428v HST with loader would fit my needs. Can I get a price check on this unit? How long is the warranty and who makes the engines in the 1428 and 1528? Thanks a lot.

Can some one tell me the ROPS height on the TC30 with R4's? New Holland's specs say 82.4" with Ags. I figured the R4's would lower it a little. My garage door is 82". I found 1 post that says it was a little over 84" with R4's. Is that correct? If so, New Holland's spec page must be wrong...

I know pricing is regional, but how much should I expect to pay for a 3440 HST with loader? Does the HST have 3 ranges? The spec page on Montana's site lists the transmission as Synchro Shuttle Hydrostatic, I don't understand this? Is this just normal 3 range HST like most other tractors...

Hi guys, Suppose I was to buy a new TC30 and finance it for 3 years. Say I wanted to get a Woods or Bush Hog loader instead of the 7308, would I be able to include the Woods/Bush Hog loader in New Holland's finacing program? Maybe a dealer could chime in on this? Thanks again.

I've narrowed my search down to the TC30 HST, Kuboto L2800HST, and Mahindra 2815 HST. All three will meet my needs. The TC30 has been out atleast twice as long as the L2800 and the Mahindra 2815HST just came out this spring. I know the TC30 is a basic machine, but it is a tried and true design...

Wrong forum

How many dealers does Kubota have in the US? Ohio? I have narrowed my choices down to the L2800HST or Mahindra 2815HST. There are 10 Mahindra dealers within 100 miles of me and only 2 Kubota dealers within 300 miles. Why are there not any more Kubota dealers. I guess if the 2 local Kubota...

Just got back from the local dealer and looked at the 2815 HST. He had it listed for $15,995 with 111 loader- I figure I can get it for $15,500 maybe. Seemed to be a nice machine. One thing that sticks in my mind was the rear axel. That was the first tractor I had seen with a rear end made...

Hi, Is the location of the joystick mounted on the right fender on the 2815 HST? I was looking at some pics of the 3215 and was wondering if that was the same set up on the 2815 HST as opposed to being on the the loader. Thanks

Hi guys, I'm in the market for a 28 - 30 hp tractor with HST and possibly a loader. Do any of the Mahindra machines in this HP range compare to the NH TC30 or Kubota L2800 in price? I have quotes for both tractors at $12,500. Right now, I'm leaning toward the L2800, but I want to keep my...

Hi guys, I have dedided to sell my Yanmar 2210D. I'm near Cambridge, OH. I tried listing it in the classified section here, but had computer trouble doing so, that is why I am letting everyone know in here. Here is where it is listed -...

Is anyone having issues with there PTO on these models? I read several posts from last year where guys were having trouble with there PTO, especially with running a tiller. I was leaning towards a 2800 HST, but after reading some of these posts, I'm getting scared. I will be tilling several...

Local dealer quoted me $10,500 for the tractor and $13,625 for tractor and loader. I thought that was pretty good quote over the phone. I could probably get him down to $13,000 or so if I go talk to him in person. What do you guys think?

Local dealer gave me a quote on the L2800 HST with the LA463 loader. He said he has been asking $12,500 for the tractor and $3,750 for the loader, but said he would take $15,500 for both. Seems a little high to me. He also said that once the one he has on the lot is gone, he is not going to...

Hi, Can someone tell me the rear track of the L2800 with R4's? Thanks again.

Hi, Generally, what are dealers stance on servicing tractors that were not purchased from them. I have a local Kubota dealer that is not very responsive to negotiating his price. I'm just wondering what would happen if I bought out of state and then took the tractor to him for warranty work...

Hi, I'm in the market for a new tractor. I've been looking at NH TC30 in particular. I have been noticing the more modern features of Montana and Farmtrac. I don't question there value and dependability, I'm just wondering if they will be around in 20 years to get parts and service? There...

Who manufacted the engines in the 2810 HST? I was thinking it was Daedong, same as Kioti. Thanks.

Hi, I'm looking at a TC30 4x4 Hydrostat with R4's and a Bush Hog 1846QT loader for $15,000. Are there any other tractors with packages that are similar in HP and price? I'm having a hard time finding something that will compare. I looked at a Mahindra 2615 HST that was similar in price, but...

Hi there, I am having problems posting an ad in the classified section. I have registered. When I try to select a category, I click on "tractor" but it just highlights the category and nothing else happens. When I click on the "Create Listing" button I get an "Invalid Category Selection"...

Are anyone of you NH guys using this loader? I might get one with a TC30. It is cheap, but the specs are not that high. I'm not going to do any heavy loader work. What are you opinions on the 1846QT? What type of jobs have you done with it? Thanks Again.

Can someone tell me the width of a TC30 track with R4's? I have a 60" rear finish mower. I was wondering if I should sell the mower when I sell my tractor and bump up to a 72" mower when I get the TC30.

Hi all, I'm thinking of getting rid of my 2210D Yanmar next Spring and getting a new TC30 4wd 9x3. I have been calling some local dealers to get pricing. I figured Corriher Imp. and Tarheel Tractor had the lowest prices so I used there prices to see if local dealers will come close. To my...

Can anyone give me a rundown as to how to adjust the valves on my 2210? Very much appreciated. D. Moore I found this in a previous post. Is this an accurate description? The procedure is very simple - each of the rocker arms has an adjustment screw with jam nut. Remove the valve cover -...

I'm putting a new head gasket on my 2210. I plan on taking the head in to a machine shop to have it magna fluxed just to be sure it is Ok. Do I have to remove the injectors before I take the head off? Can they be left in the head while it is getting magna fluxed? I'm starting to tear...

Anyone know of a sequence to use for torquing the head on a 2210? I have the specs. Thanks.

Hi guys, The head gasket on my 2210 is starting to go bad. First, let me say this is not a VN rebuild and I got it from a reputable dealer whom I am very happy with. It is in the very early stages as my fluid levels have not changed. There is no water in the oil or vice versa. I just...

Hi guys. I just ran across several good deals at Little Miami's website. It looks like he has lowered the prices on some of his tractors. There is a 1610D that has been lowered by $1000 dollars! Just wanted to give you all a "heads up" because there are some real deals there. Here is the...

Will my 2210D pull a 12" or 14" two bottom plow? I think it might, but my dad says he is not sure. He has been farming for 50+ years and uses an old Ford 600 and it pulls them OK. I think I have the power, just not sure if I have enough weight. What do you guys think?

Will 85w-140 work for the steering box? Autozone didn't have any 90wt. I getting ready to replace my pttman arm seal. Thanks guys.

HI All, I will be replcacing the pitman arm seal on my 2210 soon. I got a hammer puller to get the pitman arm off. It looks like it might be leaking grease, but I hope it has 90wt in the steering box. Is there a drain plug on the steering box? I know I have to remove the fuel tank to get to...

I am going to get a service manual for my 2210D, or rather its US counterpart. You guys that have got the manuals, which did you get, the standard manual or the CD version? Are you happy with the manual? I'm thinking I would rather get the standard version - rather have the manual get dirty...

Does anyone know how much fluid the R4 tires on a 4110 will hold?

Any bowhunters in here? If so, post some pics of your deer. Here is mine. Hardly a trophy, but I take what I can get.

I have a 2210D. Is it possible for a tractor to run too cool? While mowing this past weekend in 50 degree weather, my water temp only got up to 110. It usually runs about 150 in 80 degree weather. My coolant mixture is 33% antifreeze. I am going to go to 50/50 for winter. Is there such a...

Anyone know where to get them?

I am looking for a used wood burning furnace capable of heating 2500 sq ft home. Any one have one for sale or know where I might find one?

I have a 2210D. I was wondering what a normal operating temp should be? My tractor generally runs around 150-155 and has never went over 160. This seems quite cool compared to what others have posted their temp ranges at. I am wondering if I have a bad temp gauge. It is a Sunpro gauge and I...

Some use windshield washer fluid for ballast in their rear tires. Is this safe? What are the effects of windshield washer fluid on the tires and rims?

Does the 2210 have a water pump? If not, how is it cooled. how hard is it to keep cool.

Are the hydraulics on these tractors live, or will the hydraulics not operate when the clutch is depressed? I am looking to buy a 2210D and this is one question that completely slipped my mind.

I've read that the 2810 is not being made anymore, or production is going to stop in the near future. Is this true?

Did the 2210D ever have an American counterpart? If so, which model and how close are they related? Thanks, MDM

Which one is better made/heavier? Anyone have any experiences with either?

A friend of mine bought a 2810 HST with loader and 3 point hoe. The hoe is not subframed. He is digging a small pond and has used it to pull some small stumps. Is he heading for trouble with the hoe not be subframed?

Anyone have any experience with a Prime Cut RFM? It's made in Italy I think.

Hi, I have spent countless hours on these forums researching. Thanks for all the info. I am almost certain that I will be buying a 2210D from LMTC in the coming weeks. I would like some feedback from some people who actual own a 2210d. What are your experiences good and bad? Thanks, DM