Search results

I have a F725 with a Kawasaki FD590V engine. I started it up today after sitting all winter and had fuel spraying out the weep hole in the fuel pump. What would cause this? Is there a fix or do I buy a new fuel pump. I googled the pump and prices are anywhere from mid $20's all the way up to $165.

My seat is in pretty bad shape. Can these be recovered, or do I just need to buy a whole new seat?

I have an older metal outbuilding. The 6"X6" posts were set in concrete and I'm sure most are rotting. The one by my entrance door has rotted completely thru and shifted about 1+ inch. The inside of the barn is all concrete with part of it finished and the post are covered up. I dug the one by...

I was thinking of getting a box scraper for my Kubota B6200. From what I have read a 5' would be too big. I am looking for a 4' and found one on facebook marketplace near me. A 4' Countyline for $800, almost looks new. I googled them and it looks like TSC sold them except they only have 5' and...

I have a area in my backyard that has had standing water in it all winter. I need to dig a small trench to drain it. Any ideas on something on a 3 point hitch or attaching to the FEL to do this? I have a Kubota B6200. Thanks for any advise.

This was getting tossed out at work. Says "Toro" on the head with 433 on one side and 250 on the other. C100 on the stem. I couldn't find anything online except for the stem. It appears the stem takes a coupler and it is part of a irrigation system? It just looked like it might be worth...

Kabota front mount PTO, came off of a model B6200, Will fit other models, not sure which ones. Located in NW Ohio. $375

The old boot shot. I have a new boot and I cannot get the knob to unscrew off the shifter. Do I need to take the shifter off in order to get a new boot on?

I have a 029 that I bought new in 1994 with a 20" bar that I'm still using. Been thinking about getting a new one and that should last me the rest of my wood cutting days. I've always wanted something with a little more power than the 029. I looked at the MS291, 311 and 391 today. The dealer...

I have a B6200 with a FEL. I recently sold the mid mount deck, I never used it. I bought the tractor 15 years ago because I wanted a FEL. I still have the front mount pto. I can't think of any reason to keep it. Is there any other implements other than a snow blower that would use it? Any idea...

I have this mower deck along with the front pto. I bought a B6200DT 15 years ago because I wanted a tractor with a loader. The sub frame for the loader interferes with the deck and it has been sitting since I bought it. Any idea what the deck and pto might be worth to sell? I found a couple old...

I'm looking for a used 2nd mower/garden tractor. I came across a 2005 Cub Cadet 3206 with 325 hrs, and a 2001 Simplicity Landlord 23DLX with 1038hrs and comes with a snow blower. Both are priced $1999. I'm sure I can get a little off the price. I'm leaning on the Cub mainly because of the low...

I have sulfur water and it is treated with a hydrogen peroxide injection system which works. But that system is old and needs replaced. I have a quote for another peroxide injection system and a quote for a Smartclear air induction system which is chemical free and about $900 cheaper. Anyone...

I bought a used Citation XT which I really like. I do have a rough yard it seems like the suspension could be a little softer, it is at its lightest setting. I also have a John Deere F725 that is a smoother ride due to the springs on the seat. Has anyone done any modifications to the simplicity...

I've been looking at zero turn mowers. My first one. Mainly the Simplicity Contender XT and Gravely ZT HD with 52" deck. I haven't been able to find many reviews on the Simplicity, found a few on the Gravely and they were not as good as I thought they would be. Does anyone have any input on...

The hose is falling apart. It winds around the top of the tank before going down the side. Is there a reason for such a long hose? What problems would I have if I just run a short hose?

I know this is a long shot but here goes, I bought the tractor in 2005 because I wanted a tractor with a loader. I did mow with it a couple times then removed the MMM because I have other mowers. I have had it off for 13 years. I put it back on a couple weeks ago and have mowed a couple...

I bought my B6200 about 15 years ago. I wanted a tractor with a loader. It came with a belly mower and I mowed with it once or twice and pulled it off because I didn’t need it. Now 15 years later with problems with my other mower I decided to put it back on. It does a pretty good job except the...

I have a B6200 gear drive with a FEL. I am getting ready to change the hydro fluid. Do I just drain the transmission case and not worry about the fluid in the FEL? Or is there something I should do to get fluid out of FEL cylinders? I’m replacing with Kubota UDT fluid. Thanks for any help

I have a Century 125GL mig with the gas conversion kit. It has a preset regulator, no gauges so no way to tell how much gas is left. Is there a gauge that would go on the tank and the preset regulator would screw into the gauge rather than buying a new regulator with gauges?

I had to dismantle my mtd log splitter due to a crack in the reservoir. When I took off the filter housing the spring was loose in it. Anyone know how it is suppose to be in there? I don't see any other parts in there.

I bought this tilt trailer cheap, has 3500lb axle, going to paint put in a floor and new tires. The axle is 3 1/2" to the front of the center of the trailer bed. Normally the axle is to the rear. Being a tilt trailer is this why the axle is more forward? Has little tongue weight. I only pulled...

I have a B6200 with a FEL. The grill lights weren't very bright and the FEL was in the way. I mounted a light on top the ROP, but it illuminated me and the tractor as well as out in front and made it hard to see. Where is the best place to mount lights if you have a FEL? Thanks for any help

I have a F725 and the mower deck is barely touching the left front tire of the tractor. I wondering what the clearance is on other 725's. I can't figure out why it is so close, I cant see anything that is bent. Thanks for any help

I asked this in another forum, but I'll ask it here again since it is about a Kubota. I have a B6200DT 4WD with Bridgestone 20.5-8-10 4ply front turf tires that need replaced. The dealer or tire shops cannot find 20.5's in anything but trailer tires. My manual calls for 20.5-8-10's in turfs. The...

My Kubota B6200 4x4 has 20.5x8x10 front tires which is what the manual calls for. They need replaced but all I have found are 20x8x10's. Is the 20 versus the 20.5 going make a noticable differance when in 4wd?

Just courious on where the top link connects to the tractor there are 3 holes. What is the reason for having 3 holes and which one to use?

I was giong to make a drawbar lock for my kubota so I can have a ball on it without the bar rotating. I have seen other hitches that use the top link with a piece that goes down to the draw bar. What would be the advantage to use the kind that uses the top link instead of using just the drawbar...

I have been reading all the posts about adding rear remotes which is what I want to do. Here is a pic of what I have now. This is for a FEL. "A" comes out of the hyd. block and goes to "in" on the FEL valve, "out" from the valve to "B". The valve for the FEL doesn't have a PB port. I was going...

I have a Kubota B6200D with a FEL. Rear hydraulics was an option but dealer says kit is no longer available. Can I just tee off of the front ports that are for the loader and run them through valves and to the rear? I want to add power angle to my rear blade and maybe a hyd. top link.

I have a B6200 with a FEL and no rear hydraulics. According the manual, rear hydraulics is an option. Anyone know what is required to add this? thanks

Is a B6200 big enough for a backhoe? I would like to find one for my Kubota.

I have a model RC60-72 mid mount mower off of my B6200DT that I want to sell. It is in good condition. Any ideas on what it would be worth?

I have a B6200DT. I want to make my own drawbar. Does anyone have the specs. for one? Thanks for any info.

I have a B6200DT with FEL an 60" MMM. I have a fairly flat yard, a few dips and bumps. The rear tires spin alot when I mow in 2wd, it seems like the deck hangs gets hung up . If I mow in 4wd I have no problems. Just wondering if other people experience this?

Is $130 the average price of a service manual. Thats how much it is from the dealer. Are there any other places to find one other than the dealer?

owning-ML-716850-ML-