Search results

Cash grain farming rent $220-$240 an acre here.

I much prefer the Depstech so my smartphone can be still and just move the probe around. I would hate to go back to the old all in one units.

https://www.amazon.com/DEPSTECH-Waterproof-Inspection-Megapixels-Smartphone/dp/B09HKQMS53 Not sure how good you require but this has done everything I have ever needed.

You live near a creek? I had those several years ago and couldn't figure it out until I caught a turtle doing it.

Pump BB gun worked for me. I popped a couple in the butt a few times. Then for a few weeks went out and just gave the gun a couple pumps and they run like crazy when they hear it. Don't come in the yard no more.

Had to replace the fuel filters on my 1211 at 106 hours due to it not sucking fuel out of one tank. Been even ever since.

I had to send Owens-Corning a shingle sample removed exactly per their instructions packaged a certain way. They replaced my 5 year old roof including underlayment and labor at no cost. 47 square. I had 6 bad shingles on one spot on my garage. Obviously from a defective bundle, rest of roof was...

In Ohio you can transfer 2 vehicles outside of probate between husband/wife. Anything over that lawyer had me get TOD titles.

I have been running G6 on a 72"SD for 2 years. I like them but in the fall when it is dry the front blow out can be annoying. I have machined a number of sets of the holders for these blades for other owners.

I have 3 Morton buildings with the oldest being 38 years old. Just had the roof repainted 2 years ago, rest still looks fine. My first building, 54 X 90, only had enough scrap after building to fill a wheelbarrow. Built 2nd in 2002 and before I built the 3rd in 2005 I went around and checked out...

He doesn't have stuff tied down.

Scrap haulers

Just for reference, here is a turbo mounted on a 3 cyl Kubota

On the last two large buildings built here with laminated posts, the treated 3 2X6 bottom sections are set in the ground with sackrete. Then a jig is used with a lazer and the treated posts were all sawed to the same heights, stair-stepped. The walls were bulit in sections and then set on the...

I took a piece of 3/4" copper tubing and flattened one end and soldered a fitting on the other with a ball valve and hooked to an airline. So far works everytime. Sort of a scaled down version of one of these:

Those silos are great, I tear them down and build cabins like this out of them.

My cabinet is standard but is mounted away from the wall so as not to be hard to reach. The wall behind the fridge is sunk in 7 inches or so just in the fridge area, not the whole height.

Why don't you just put 3' tin up? Just screw it right to the trusses, no 2X4's, taping, painting, etc. I had a 54 X 90 on 9' centers done this way. Have two other buildings on 7'6" centers done this way also.

I've done a lot of work on D1105 engines which is what is in your 1100. Have about 6 of them here now. Not sure on room in your engine compartment but Kubota made a D1105T which is a turbo version of your engine. If you want you could look at the factory manifold and turbo setup and see if it...

$64,000+ Kubota skid loader at National Farm Machinery Show.

I have a 42 X 45 and a 54 X 83. Both are insulated on the sidewalls with 6" fiberglass covered with painted OSB and ventilated soffit for noise control. You can get rolls of insulation 7 1/2 feet wide to go between the posts. Ceilings are metal with fiberglass cubes blown in. I helped a...

We make most all our turbo pipes out of stuff like this: Hooker Headers 12210 Hooker Headers/Dynomax Exhaust Tube Mandrel Bends www.iceman-motorsports.com

Adapt one of these to front of your turbo inlet. Spring load it. Run a choke cable with a ring pull on it from the rear up to it and run it thru the hole. If you ever put an electric pump on you will have to add a power disconnect to the same ring. You will eventually need an electric pump...

This one is lots faster

May be time to get some real power out of it :)

Columbus Winternationals 2010 #2

Columbus, OH Winternationals 2010

Does anybody else here do this?