Hey, since we mostly stick around here and post, I thought I would start a new thread (like others have done for different color tractors) for us to post about what we have done with our GC...

Tractor is located approx 150 miles from me and I need to trailer it to my home. Tractor will not start so use of hydraulics is out and no other tractor available to switch hydraulics. When...

Built this cab for my massey gc2300 out of 1"x1" 100 wall tubing with Lexan attached to the tubing.As you can see sure it looks a bit boxy looking but the ROPS is inside the cab.The ROPS that came...

im just curious about some opinions, spicificly how loud is the mahindra compared to the others, and hows the ride and performance?

Thought I would repost these for those who may not have them: GC2300/2310 OEM part #'s: Engine Oil Filter:3609410M1 Engine Air Filter:3757472M1 Trans Oil Filter:4265229M91 Fuel Filter:3608255M1...

My tractor was stolen and Insurance will be covering it. I spec'd out the BX2350 and I think that's what I wanted. Insurance has spec'd out the Massey GC2300 (and it's more expensive). Can...

I have a MF GC2300 with a front end loader. The controller for the FEL is a Nimco Controller. If you are on the tractor the right valve stem is leaking. This is the second time this has...

Please help me decide between these two tractors. The MF is $500 more expensive. Is it worth it? The MF seems to be a little bit heavier built tractor. Please help!!!!

I just bought a used GC2300. Serial number M-T0501. I'm hoping I can clear some honey suckle from my woods. This is my first tractor with a 3 point hitch so not sure which attachment to get first...

Tractor has broken Iseki motor e3112. Having problem locating parts. Anyone do a motor swap to another 3cyl diesel??

Hello, I am in eastern Ontario, Ottawa Valley and am interested in switching my MF GC 2300 for a Kioti 30hp gear. My MF is 6 years old and having a lot of nagging problems and break downs, all...

We have 12 acres of land. We currently have a 12 year old Ingersoll garden tractor with many attachments but it isn't substantial enough to do the work we want to do on about four acres of brush...

Thanks for all the replies on my previous post! I'm still trying to decide! I'm just wanting a tractor small enough with MMM for mowing 2- 1ac. lots and on ocasion may take this tractor to work...

Has anyone ever installed a engine heater on a Massey GC2300? The dealer priced one to me with me installing and the cost seems high just for a part; $90.00, I don't know if there is enough...

Well it finally arrived this morning at around 11am. It was something to see it coming up the driveway. My excitement level has been at maximum all day. i'm trying to post picture from my...

Hello all, I have a GC2300 that's a few years old. A few days ago I noticed a drip on one of the hoses on the right side of the 2350 FEL. I don't know much about these hydraulic system of these...

I am new to the forum and wanted to know if anyone is having the same problem as me and knows a solution. My gc2300 starts and runs fine but will not turn off. I had to kill fuel and it stays...

the catalog I can afford. ha ha. most specs seem superior to Kubota BX. hmmm

Good Evening All, I just completed my 300 hour maintenance schedule for my MF GC2300. While installing the transmission filter I noticed the plastic fan is missing a couple of blades. First...

I've searched high and low without finding the part # on the web. Thanks:thumbsup:

Here's what I know: battery checks out at 12.24 volts. tractor won't turn over. jumped, it will turn over until the jump starter quit .but not start, tho it did a couple of times yesterday. My...

Thanks for all the help with my SCUT buying decision. I decided to go with the MF GC2300. It was just delivered about 3 hours ago. The information that all the TBN members that replied to my...

Hi all...I am new to the forum and new to tractors...I have a lead on two units...one old, one new: Ford 1220 - 1989 (serial #) - $7800 - Shibaura engine - Power Steering - Loader - Mower with...

Greetings, Last summer my GC2300 with FEL started cranking slow when hot. I don't mean overheated but hot after normal use for 30 minutes or so. If I shut it off when hot it will not crank fast...

I went to look at two used tractors today. Both 4wd with loader. I liked the MF but am concerned with the ground clearance. It seems kinda low. It has turf tires on it, I am trying to find out if...

Purchased my GC2300 about a month ago with 333 hours on it. I don't believe the previous owner knew what a grease gun is. Some of the fittings required breaking the ball lose, so the grease would...

Hey there, I'm new here and I'm trying to learn a little more about this particular tractor. Has anyone used this tractor for lite landscape work? Seeding, fertilizing, small grade box, or roller...

Need motor mounts and oil pan for Massey gc2300. Iseki e3112 motor. Motor mounts failed and motor wore hole in pan.

This is My MF GC2300 Texas Longhorn Special Edition.

Looking for replacement boots for the tie rods of my GC2300. Called the dealer and they want $27.90 each, for a piece of rubber. I asked them to double check and they confirmed. Do you know...

I recently was gifted a mf gc2300. The left rear axle seal is leaking. I purchased a massey ferguson shop service manual but it's not really clear if I can replace the left rear axle seal without...

I am trying to find an engine rebuild kit for a 2002 massey ferguson GC2300 with an E3112 engine. Anybody have any idea where to find a complete engine overhaul kit for it? Thanks

I have not seen anyone talking about the 2300 here on TBN even in the Massey Section! Are they selling any units? I thought with the competition of the BX and the JD 2210 we would see it mention...

Hey guys, New guy here to the site! I came into ownership of this Massey about six months ago and I figured I'd get a snow plow for it. I drove to Maryland and bought a plow I saw on Craigslist...

I'm looking at a Kubota 7500 HST or a M.F. GC2300. I'm going with a front end loader, rear offset tiller and a belly mower either way. I'm looking for opinions on either of these as I am a...

Hi guys, a Newbie here..... I have a GC2300 with a rear mount 50" Meteor blower. Works awesome, but neck starts to bother me after a while (too much golf). I had a JD X300 with a front mount...

I was wondering if anyone knows of an aftermarket front snowblower attachment or if anyone has modified a different manufactured unit to work. I saw the Deere blade conversion, but I'd really...

Here are the details on the GC2300. This is a sub-compact that competes head to head with the BX Kubota. This tractor is made by Iseki for Massey Ferguson. It is exclusive to Massey Ferguson in...

The rear axle seals on my GC2300 are leaking. Is there an easy way to get the axle shafts out?

Something broke inside the motor haven’t cracked it open yet but oil pan cracked so thinking rod. Need to source internal parts for Iseki e3112 motor but not having much luck. Anybody have...

Just posted this in the parts repairs section. I am looking at buying a 2003 GC2300. It isn't equipped with FEL hydraulics. How hard is it to add all the stuff for this and does anyone have an...

lost voltage to switch all fuses are good any help thanks!!

I was just clearing a few inches of snow before a larger storm hits tomorrow night, and after pushing hard into a snowbank there was a large puff of black smoke and the engine sped up without...

Does anyone know a good online dealer for these parts? Has anyone cross referenced rings and bearings?

I need a starter relay for my MF GC2300. The number on the bad relay is ACB33421.

HEINS EQUIPMENT COMPANY INC 4030 CHATHAM ST (STATE RT 203) VALATIE, NY 12184 (518) 758-9881 fax (518) 758-1658 888-758-9881 Parts Order Line t.heins@berk.com Ask for Trevor... tell him Johnny...

has anyone had problems with the placement of the hydrostatic filter ? I just had mine break off while driving over some dirt piles.

The Oregon 91-144 is 20.5” long, 3” wide, .203” thick and 1/2” offset . The ones I got from an Massey Dealer are 20.5” x .25” x 2.37” . Not sure of the offset. Would there be any issue if these...

I hope I am posting this in the right place new here so I apologize in advance. I have a 2004 Massey Ferguson GC2300 and my loader which is actually a MF 2350 loader, goes up with no issue bucket...

I have a GC2300 the 3 point hitch won't go up. The control lever seems to operate but I can't see where it actually connects to a valve or anything that would control the 3 point hitch? How or...

My Massey Ferguson GC 2300 is leaking hydraulic fluid from the right rear axle. I was wondering how to remove the axle and replace the seal. New to the forum. Any info would be appreciated.

The other day I noticed a small leak from my FEL valve on my 2004 gc2300. I have replaced these leaky o rings before and thought I could swap another one quick. I took the valve apart and...

i just purchased a second Massey Ferguson GC2300 - this one with a 2350 loader. the tractor has about 1800 hours on it and is in very nice condition. the loader feels weak to me as it labors to...

The float on my FEl is not working. It won't go into float. It seems to me quite a while ago I saw something here about cleaning the gunk out of the valve to free it up. Anyone have the details...

I changed the hydraulic fluid on my GC2300 last night. It all went pretty well until I got to the suction screen. I removed it and was surprised that there were metal shavings on it, but I guess...