murphy1244
Super Star Member
- Joined
- Nov 25, 2011
- Messages
- 16,335
- Location
- Ohio
- Tractor
- Kubota 1120 RTV Kioti DK-40, MF-135, Ventrac 4500Y
Why were some of my posts removed? I have followed the rules.
Backhoe Zerks for KB 2485~ size?....
- Thread starter Coyote machine
- Start date
- Views: 21077
- Status
Sometimes we remove posts that are in reply to posts that need to be removed in order to keep the flow of the thread.
murphy1244
Super Star Member
- Joined
- Nov 25, 2011
- Messages
- 16,335
- Location
- Ohio
- Tractor
- Kubota 1120 RTV Kioti DK-40, MF-135, Ventrac 4500Y
Ahh, I see now. Thanks for the input.
OP
Coyote machine
Super Member
- Joined
- May 4, 2009
- Messages
- 7,641
- Location
- Southern VT
- Tractor
- 22 SANY SY 50U, '10 Kioti DK 40se/hst KL-401 FEL, loaded tires, KB-2485 bhoe, Tuffline TB160 BB, Woods QA forks, MIE Hydraulic bhoe thumb & ripper tooth, Igland 4001 winch, & GR-20 Log Grapple. Woods BBX72" Brush Mower. Diamondplate aluminum canopy
Murphy,
The posts removal isn't about anything you posted.
The posts removal isn't about anything you posted.
murphy1244
Super Star Member
- Joined
- Nov 25, 2011
- Messages
- 16,335
- Location
- Ohio
- Tractor
- Kubota 1120 RTV Kioti DK-40, MF-135, Ventrac 4500Y
otay whatever..
CJONE
Veteran Member
Yea, I noticed mine got removed also. But the recommendation on the drilling and tapping to 1/8" pipe is still a option. We sell Zerks for about 16 cents and they are steel not brass. CJ
PatasColo
Silver Member
- Joined
- Nov 23, 2010
- Messages
- 228
- Location
- Front Range of Colorado, USA
- Tractor
- Kioti CK20S HST and Gravely walk-behind (2 wheel tractor - 700 lbs.).
Re: Zerks for KB 2485~ size?.... My 2 cents
I beg forgiveness if I misinterpret, but that post (quoted) makes it sound like you think the needle tip is used around the edges of a joint (i.e. where the grease squeezes out). This is not the case. The needle tip is placed right in the center of the zerk, where it presses in the ball, and the grease goes in... into the same place as if a standard grease coupler is used.
I agree that if you try to grease the edges of a joint with that needle tip, the grease won't be where you want it... and it would take you 5 hours and 22 minutes to grease around the whole tractor!!! :laughing::laughing:
-Mitch
I beg forgiveness if I misinterpret, but that post (quoted) makes it sound like you think the needle tip is used around the edges of a joint (i.e. where the grease squeezes out). This is not the case. The needle tip is placed right in the center of the zerk, where it presses in the ball, and the grease goes in... into the same place as if a standard grease coupler is used.
I agree that if you try to grease the edges of a joint with that needle tip, the grease won't be where you want it... and it would take you 5 hours and 22 minutes to grease around the whole tractor!!! :laughing::laughing:
-Mitch
dustinfox
Gold Member
Re: Zerks for KB 2485~ size?.... My 2 cents
Thank You Muhammad! :thumbsup:
Thank You Muhammad! :thumbsup:
OP
Coyote machine
Super Member
- Joined
- May 4, 2009
- Messages
- 7,641
- Location
- Southern VT
- Tractor
- 22 SANY SY 50U, '10 Kioti DK 40se/hst KL-401 FEL, loaded tires, KB-2485 bhoe, Tuffline TB160 BB, Woods QA forks, MIE Hydraulic bhoe thumb & ripper tooth, Igland 4001 winch, & GR-20 Log Grapple. Woods BBX72" Brush Mower. Diamondplate aluminum canopy
Muhammad deleted posts from this thread at my request to either close the thread, eliminate it completely, or edit it, as was obviously needed.
Any other interpretations are merely misguided wishful thinking.
I would say, however, I would have preferred it being eliminated completely, but I left the decision to the admin.
Any other interpretations are merely misguided wishful thinking.
I would say, however, I would have preferred it being eliminated completely, but I left the decision to the admin.
Jesse masterson
Platinum Member
The thanks wasmt to ypu it was to Muhammad , others also complained not just you, but that's right your "special"
- Status
