Rockgod
Platinum Member
Reference:
4720 3rd, 4th & 5th hydraulics
- Thread starter SwLWildcat
- Start date
- Views: 25250
Reference:
OP
SwLWildcat
New member
I installed the LVA16893 line and all is perfect! Thanks. Next problem. I got the power beyond kit to install now and I have the same issue. The kit would work great if I didn't have the 3rd, 4th & 5th kits installed. The lines supplied are for a bare tractor without any additional service valves. JD110 would you happen to have another diagram?
OP
SwLWildcat
New member
Thanks Jd110. That is exactly it. I have the 1 line, just need the other 2.
OP
SwLWildcat
New member
Thanks again JD110. Just thought I would toss up a picture of it all assembeled. You part numbers were perfect fit.
arlen4720
Veteran Member
- Joined
- Jul 6, 2012
- Messages
- 1,277
- Location
- Southeast Minnesota
- Tractor
- JD 4720, JD X748SE, JD 997, Farmall "B", Gator 865R, JD 320D Skid Steer
Looks Good.
What are the 2 manual valves for?
You don't get over to the "other forum" any more? I posted a document for you a couple of hours after you were asking about what parts you needed, but I see you never logged back in.
OP
SwLWildcat
New member
Ah, good question. I was rigging up a grapple for my bucket and I want to run a hydraulic thumb on my 485. I was just going to plumb the thumb into the 3rd quick couplers and then when I want to use it I can just shut off the flow to the front end grapple. I may just use the 4th or 5th spool instead. I am just in the process of building a thumb now, so that will probably be a week or two away. A hydraulic thumb is so nice for placing culverts...
arlen4720
Veteran Member
- Joined
- Jul 6, 2012
- Messages
- 1,277
- Location
- Southeast Minnesota
- Tractor
- JD 4720, JD X748SE, JD 997, Farmall "B", Gator 865R, JD 320D Skid Steer
Have you played with the 485 yet? I've considered getting one, I just want to make sure it is a "real" backhoe. I wonder if JD will ever offer a hydrulic thumb. I'm curious to see what you come up with.
OP
SwLWildcat
New member
Yes, I have played a bit. I dug a 40' trench (seen in pics) it's about 4 1/2' deep at one end and tapers down to nothing on the other. The gas company had flagged a gas line crossing about 1/2, but no reference as to how deep it was. I put in a 16" culvert. The whole thing took me about 3 1/2 hours, including digging near the gas line by hand with a spade, and buring the whole thing when done. It's a pretty decent back hoe. My biggest complaint is I am used to the ISO pattern, so the dipper and the boom are backwards for me. It's hard to teach an old dog to change. I'll post something when I get the thumb on and running.
arlen4720
Veteran Member
- Joined
- Jul 6, 2012
- Messages
- 1,277
- Location
- Southeast Minnesota
- Tractor
- JD 4720, JD X748SE, JD 997, Farmall "B", Gator 865R, JD 320D Skid Steer
Does it have the "creep to reposition" feature? If so, can you reach through the window to run the loader up and down? I have an open station, I could probably use a stick or something. One thing that disturbed me a little bit after seeing how the hydraulics are plumbed up (on mine), is that it appears that the power beyond will disable ALL rear hydraulics when the hoe is on. I was aways under the impression that the PB was plumbed AFTER the rear SCV's but BEFORE the rockshaft. It actually is BEFORE all of it. I thought it would be nice if the grapple would still work at least (3rd EH SCV). I could see wanting to dig up a stump, then carry it off with the loader/grapple.
How is yours plumbed? Mine is: Pump, PTO clutch, Mid SCV, PB, 4th & 5th Lever SCV's, 3rd EH SCV, then Rock Shaft.