Starting my bridge!!

[LD1]

Did you ever say what you were going to use for decking?

And curious why you chose 2.5' spacing.

Car trailers and even some equipment trailers have cross members on 24" spacing......and that seems to work pretty well with 2x8 or 2x6 treated lumber. But not sure how 30" spacing would work.

IF you have some hardwood sawmills in the area.... full 2" rough sawn white oak is alot stronger and lasts just as long as treated pine

 

[LD1]

Been following this build as I have a very similar landscape on the back of 20A and eventually want to build a bridge that would hold about 7000#. If anything my creek might be like a 2ft wider (longer span for the bridge). You had mentioned "I" beam...I have an old 14'x70' mobile home that is basically garbage except for the steel I beams under it (its an old one with the 1-1/2" outside walls). Those I beams are about 12" to 14" high and the steel in them is 5/16". Could I repurpose those I beams to build a similar bridge that would hold the weight I need?

There is no guessing when it comes to steel and sizing.

I cant work off of "about 12" or maybe 14" tall".....or "maybe 2' longer span"

Need to know specifics. Need to know exact dimensions of I-beam, exact span.

Then on the typical mobile home I-beams.....bracing is key. Because they are so tall and thin.....they naturally want to flop over on their side.

So...."can" a 14x70 mobile home frame be made to work.....YES it can. But can it also fail if done/braced improperly.....also a yes.

And dont take any of this as gospel. This is just an internet forum and the advice you receive is worth exactly what you pay for it

 

[51allis]

There is no guessing when it comes to steel and sizing.

I cant work off of "about 12" or maybe 14" tall".....or "maybe 2' longer span"

Need to know specifics. Need to know exact dimensions of I-beam, exact span.

Then on the typical mobile home I-beams.....bracing is key. Because they are so tall and thin.....they naturally want to flop over on their side.

So...."can" a 14x70 mobile home frame be made to work.....YES it can. But can it also fail if done/braced improperly.....also a yes.

And dont take any of this as gospel. This is just an internet forum and the advice you receive is worth exactly what you pay for it

Thank you, I know there would have to be some kind of engineering mathematics etc. Im not ready to build it just this year, its project Ive been thinking about just so that I don't scrap the whole mobile home and throw away good steel. I do understand what you are talking about as far as needing more information etc. Is there a book on basics for the engineering math on bridges etc.? Not sure I worded that right but reference materials for bridge building that YOU would recommend a person read before starting any bridge project? Thanks for your input, much appreciated.

 

[Southernspeed]

I built a bridge at my old farm. 16’ span, 6’ wide for ATVs and equipment and horses mainly. Built it out of 4x6 treated lumber, four of them spanning the creek, resting on 6x6s, topped with 2x6 treated boards. It was solid, weighed more than the moon and never even flexed with the heaviest loads I drove over ( ATV and trailer)
Then we had ‘that’ storm! I’d never seen the bottom like it. My shooting range was two or three feet deep in fast running water. Two weeks later it had dried enough to get down there. My bridge was gone. It was thirty yards down stream, up the bank and wedge between two trees.
And that’s where it stayed!
Anchor your bridge down if there’s even the remotest chance that area can flood!
Looks great BTW!

 

[Gord Baker]

Great project. Sometimes you can purchase a Highway Trailer flat bed 40-50+ feet long and cut off the undercarriage. Once you get it across with Dozer or crane, lay the ends on a few Railway ties. Done.

 

[Bill601]

I really wanted to comment as soon as I saw this post, but I made sure to read the whole thread all the way through first.

I understand why you're building this the way your are. You're a good welder and have access to free materials. Makes sense. I won't argue with your design. Others more knowledgeable than I have already rung in on that. And time will prove it out one way or the other.

My only question is whether or not it would have been feasible and/or advantageous to put a culvert pipe in there and fill gravel and dirt over it? Just guessing maybe a one 2', a 3', or two 2' culverts? Just asking. Maybe the pipe is too expensive. Maybe the span is too far.

Best of luck with it. Looking forward to more updates and photos!

Bill

 

[deezler]

Great project and thanks for sharing. Nice work so far!

But your design gives me great concern, so heres 2 cents you didn't ask for.

You want to drive a 6000 lb f150 across a 7' wide bridge? That sounds terrifyingly narrow. I made sure to get just over 9' wide for mine, which is very comfortable for tractor. Still haven't tried my truck across, but the weight is the same as my fully loaded tractor.

Furthermore I have to defer and agree to LD1's gut call on your designs capacity. It's a pretty long span for such little metal! At the very least it will probably be very bouncy (no big deal) but my fear would be that it taco's in half as soon as you put 3500 lbs in the middle of it (truck front axle, or tractor front axle with heavy loader bucket load, for example).

I don't think adding some design bandaids like cables or a little pole truss railing on each side is going to give you the capacity you were hoping to have. Maybe I am completely wrong here, but, beware.

I really wish you had put concrete foundations down to frost line. A ground contact 6x6 should stay mostly intact for a while, but eventually your abutments are probably going to be getting soft, collapsing into the mud, and/or frost heaving to funky angles.

You are building a kickass 4-wheeler bridge, but for a pickup truck? Doesn't look like it, sorry. I like the other notions before my post, to maybe just lay a used trailer deck across what you have going here already, to add a lot of extra strength.

Carry on and please keep us updated!

 

[LD1]

Thank you, I know there would have to be some kind of engineering mathematics etc. Im not ready to build it just this year, its project Ive been thinking about just so that I don't scrap the whole mobile home and throw away good steel. I do understand what you are talking about as far as needing more information etc. Is there a book on basics for the engineering math on bridges etc.? Not sure I worded that right but reference materials for bridge building that YOU would recommend a person read before starting any bridge project? Thanks for your input, much appreciated.

Just google steel beam deflections and steel beam stress.

You will get all kinds of formulas......distributed loads, point loads, etc.

But all common steel has given properties. All common I-beam shapes, Channel, tube, etc.

Its simply math from that point. The key spec you are looking for to calculate deflection is called moment of inertia (i⁴) You can get some I-beam specs here W-Beams - American Wide Flange Beams

The LIGHTEST 10" I-beam they list is a W10x12. Meaning 10" tall and 12lbs per foot. And has a moment of inertia of 53.8

For simple deflection with a load at mid span.....(WLᶟ)/(48Ei⁴)
In other words......weight times the length in inches cubed.....divided by 48 times modulus of elasticity times i⁴

Modulus of elasticity of steel is 30,000,000

So, with 3000 pounds at the middle of a 22' span:
(3000 x 264 x 264 x 264)/(48 x 30,000,000 x 53.8) = 0.712" of deflection.

You should try and keep deflection under L/360. So 264"/360 = 0.733 So a pair of those beams in theory is good to a little more than 6000# total at midspan with a point load.

But with steel members that arent common.......or listed anywhere.....for example if your trailers I-beams arent actually I-beams but rather plates of steel welded together.....or in the OP's case of maybe stiffening tubing with cable or strap or re-bar.....makes it VERY complicated to calculate the moment of inertia. And therefore very difficult to assign a proper load value. Because alot more things come into play other than just raw steel. For example.....quality of the welds, enough weld contact area, bracing, etc.

A fun little tool/calculator I downloaded years ago so I dont know if its still avalialbe is called BeamBoy. It calculates all the stress and deflection for a given shape. And they have alot of shapes already stored in the program with the relevant parameters.

So in the above example of the 22' span and W10x12 beam it looks like this:

 

[olenjohn]

That pesky “hiring” word…….
My neighbor has a couple excavators but I hate imposing.
The chute idea isn’t bad…….
I do have a teenage boy with friends and some wheel barrows.

Use a wheel barrow. Contractor grade 6cf will move a yard in 5 trips. No brainer with strong boys with weak minds. Redimix truck chute will reach over 1/2 way across the bridge. Screwing around with chutes or excavator would take longer than the wheel barrows

 

[2manyrocks]

I built a bridge at my old farm. 16’ span, 6’ wide for ATVs and equipment and horses mainly. Built it out of 4x6 treated lumber, four of them spanning the creek, resting on 6x6s, topped with 2x6 treated boards. It was solid, weighed more than the moon and never even flexed with the heaviest loads I drove over ( ATV and trailer)
Then we had ‘that’ storm! I’d never seen the bottom like it. My shooting range was two or three feet deep in fast running water. Two weeks later it had dried enough to get down there. My bridge was gone. It was thirty yards down stream, up the bank and wedge between two trees.
And that’s where it stayed!
Anchor your bridge down if there’s even the remotest chance that area can flood!
Looks great BTW!

My neighbor had a wooden bridge to drive their cars across that had oak tree trunks for beams and heavy oak boards from the sawmill. It washed downstream into my concrete bridge in a bad storm. I guess wood still floats even if it's heavy as blazes.