Good morning!!!!

[jbrumberg]

Kilroy- I hope that get some relief tonight; Good luck.

The sun is starting to make its appearance this afternoon with brief periods of blue skies and/or sunshine. The current temperature is 51ºF which may become today's high temperature. I took advantage of the weather to vacuum the hair out the . It's futile, but the only alternative is to wear a full face respirator mask or a hazmat suit. At least he is "dry-mouthed" unlike our St. B.'s so I do not have to deal with drool stalactites or stalagmites.

 

[rswyan]

55F and generally cloudy @ 14:45, calling for a mix of sun and clouds and high of around 59F. Radar indicates some lingering showers in the area ... but I'm not sure if they are even reaching the ground.

Woman just got back from another appointment @ the dentist, visit went well ...

Ended up being a relaxed pace day yesterday.

Got hopper feeder and one suet refilled, plus some cracked corn scattered for the ground feeders. Suet feeders seem to be getting hit real hard lately.

Loaded up some of the Biesenmeyer fence parts in the van and got those moved up to the shop.

Front rail for the fence cleaned off and installed on the Unisaw. That needed to have the height of the horizontal flat set 2 27/32" below the table top.

Manual mentioned an included template to be used for doing so, took a little research online before I managed to figure out a combination square could be used to accomplish the task and got that done (Doh !)

Got quite a bit of cleaning done around the double-barrel stove, picking up all the crud off the floor.

That allowed me to move the table so there is more room near the overhead door.

Hauled in a bunch of wood to dry out.

Woman went over and got dinner from the good Mexican place, watched Nature on PBS and ended up falling asleep during NOVA so did not make it back up to the shop.

Agenda for the rest of the day:

Get fire started up in the shop.

Get rear rail and rectangular tube for fence cleaned up and installed on Unisaw.

Dig through the various blade guards and splitters from the auction and see if there is anything that can be modified to use with the Unisaw.

Will likely wait until tomorrow when it's warmer and the Sun is out to move Unisaw down to the garage here at the house.

Hope everyone is having a good Thursday ...

 

[Thomas]

48F 10mph wind from the north on/off shower until tomorrow morning.

Boo came by over night left thank you on front lawn... again.
Deer starting to thatch their hair and birds picking up hair,must be for their nest.
Soon clean area for 2 cords wood out of 6 cords being deliver around 6pm.

Evening plans not that much after grilling hotdogs with fixings...feet up share bowl ice cream hit sack little earlier.

Enjoy your evening all.

 

[KilroyJC]

Hope they get your back sorted out Kilroy

Me too!!!!!!

 

[KilroyJC]

Kilroy- I hope that get some relief tonight; Good luck.

The sun is starting to make its appearance this afternoon with brief periods of blue skies and/or sunshine. The current temperature is 51ºF which may become today's high temperature. I took advantage of the weather to vacuum the hair out the . It's futile, but the only alternative is to wear a full face respirator mask or a hazmat suit. At least he is "dry-mouthed" unlike our St. B.'s so I do not have to deal with drool stalactites or stalagmites.

Thank you!!!!

 

[buckeyefarmer]

Hey, the app is working, at least right now.

 

[buckeyefarmer]

60° and mostly sunny.

With last week’s streaming issue, I bought new hdmi cables.
Rented the 16 ft step ladder again today. Installed new hdmi over fiber cable that supports 8K video. Pulled older Ethernet cable out to pull new cable in, as the new projector has WiFi. Left the old hdmi cable and vga cable as they didn’t want to budge in the conduit.
Lot of up and down ladders.
Once that worked ran another Ethernet cable thru attic, that feeds our streaming camera. I had it temporarily tacked to the wall for 2 years.
Only work left is to in the sound room, run the 2 cables down wall, right now I left them hanging thru the ceiling.
Was getting warm in the attic by the time I finished.

 

[m7040]

Gilroy hope your Chiro appointment goes well and gets you some relief

 

[Popgadget]

Hey, the app is working, at least right now.

I use Tapatalk, it wasn’t working either, but seems ok now.

 

[m7040]

55F and generally cloudy @ 14:45, calling for a mix of sun and clouds and high of around 59F. Radar indicates some lingering showers in the area ... but I'm not sure if they are even reaching the ground.

Woman just got back from another appointment @ the dentist, visit went well ...

Ended up being a relaxed pace day yesterday.

Got hopper feeder and one suet refilled, plus some cracked corn scattered for the ground feeders. Suet feeders seem to be getting hit real hard lately.

Loaded up some of the Biesenmeyer fence parts in the van and got those moved up to the shop.

Front rail for the fence cleaned off and installed on the Unisaw. That needed to have the height of the horizontal flat set 2 27/32" below the table top.

Manual mentioned an included template to be used for doing so, took a little research online before I managed to figure out a combination square could be used to accomplish the task and got that done (Doh !)

Got quite a bit of cleaning done around the double-barrel stove, picking up all the crud off the floor.

That allowed me to move the table so there is more room near the overhead door.

Hauled in a bunch of wood to dry out.

Woman went over and got dinner from the good Mexican place, watched Nature on PBS and ended up falling asleep during NOVA so did not make it back up to the shop.

Agenda for the rest of the day:

Get fire started up in the shop.

Get rear rail and rectangular tube for fence cleaned up and installed on Unisaw.

Dig through the various blade guards and splitters from the auction and see if there is anything that can be modified to use with the Unisaw.

Will likely wait until tomorrow when it's warmer and the Sun is out to move Unisaw down to the garage here at the house.

Hope everyone is having a good Thursday ...

You are on the home stretch of finishing the best Unisaw out there