Recent content by Gomer

Does anyone have the generic (NAPA) part number for the rubber boot for K2561-0163-0 axial ball joint. Earlier posts suggest they are available. Mine are torn and need replacing before winter so I don't ruin the ball joint. I saw earlier posts on putting inner tubes over them but prefere to...

Just a little "heads up" here on hydraulic filters. I have a B2630 and had a dented suction filter (from a stick). So I thought hey why not save a few bucks and buy a NAPA filter for it. Everything seemed OK until the oudoor temps started dropping and it took longer and longer for the...

Built some guards for my hydraulic filters and thought somebody might wnat to see how I did them, so here you go. You can see by the old filter why I needed it. Little tip: if you want to change the filter without draining the oil I put a small vacuum cleaner on the fill port. Be careful as...

NAPA Filters : Filter Look-Up Hope this helps someone!! Gomer

I have Titan Multi Trac C/S 24x8.50-14 front tires on my B2630. I ran over a stump and put a small tear in the sidewall. I looked online for a replacement and found the Titan tire store that said muli trac c/s are manufactured by Titan and Carlisle and they make no distinction between the two...

Thought I would share a little hydraulic project I did for a thumb on my B2630 bucket. I built some brush forks and could not keep the brush on the forks so I bought a thumb and plumbed it up per the pictures. Works great. Next time I put the thumb on with the forks I take a couple of Pics.

I made up some more of these for sale. $15 plus $5 shipping. The picture installed is of the original one I made, the other picture is of the one I made up for sale. The original one was made of 11 guage the ones I made up for sale are 14 guage, still plenty heavy to stop ripping your filter...

Does anyone have experience with the quick couplers from discount hydraulic hose.com? Good, bad, pay the extra $4 and buy snap tites?

I have two different kinds of quick connect couplings on my tractor and I am trying to get this straight. Is there a secret decoder ring required? Kubota dealer said I have to order from Kubota as nothing else works. DMP(?) PBV-06F and Snaptite 72CF Is there a standard? Who makes them and are...

I have been searching old threads and believe I have found the answer but not sure. I want to do some plumbing. Somebody surely has gone through this. I know very little about hydraulics. What size quick connect couplings are on my FEL? What do you ask for? model? series? 3/8" B-72 Series snap...

I an planning to add a thumb on B2630 FEL and would like to add a diverter or selector valve to the FEL control so I can switch between rolling the bucket and pinching the thumb. I found these two valves and I know very little about hydraulics but I think only the one (1782)will work. Would...

I an planning to add a thumb on B2630 FEL and would like to add a diverter or selector valve to the FEL control so I can switch between rolling the bucket and pinching the thumb. I found these two valves and I know very little about hydraulics but I think only the one (1782)will work. Advise...

I have a 2782 blower for my B2630 and a dolemite(limestone) driveway. So I have been reading about adding a 1" pipe to the bottom of the blower to help with NOT picking up stones.:eek: Well I am confused about exaclty how to install this.:confused: I have read where someone mounted it all the...

I am installing a snow blower chute rotater and it won't work on these ports, only turns one way, but will work on the other two. The blank (inner) ones are used for the blower lift cylinder (came that way from the dealer). The blower lift cylinder will work on the ones I show hooked up...

I am moving brush and small logs in the woods and am considering adding some type of protection from stray logs and trees. Something from top of ROPS to the FEL upright mounts is what I am thinking just to keep thing from wacking me. Anyone do something like this? I have a B2630 but the concept...