Bought a Montana 5740c last fall and used it through the winter. Now I am ready to bush hog today and have never ran the PTO. Hooked up the cutter and ready to cut... Nope! My PTO comes on and shears the pin. Idle down at the lowest point of 750rpm. Sheared 5 pins with no luck and I gave up...
Just bought a used 5720c with loader. Looking where I can get a service manual to pull the transmission. Has noise when not under load. Bearing noise but goes away when in creeper gears. Going to take apart and fix before it gets worse. Any help appreciated.
JT in NC
I am trying to identify the trencher that I bought yesterday. I have looked and can not find the manufacturer anywhere. Also can I just install a single spool valve to operate the up and down of the boom. I already have a power beyond kit on my 955 Deere.
My dads neighbor stole over a year from his barn. This consisted of what he could carry through the woods and sell for scrap. Dad has a plugger and it had the parking stands to hold it up for attachment. Well the thief stole them and left the plugger on the ground. At 75 dollars a piece I am...
Putting my dads Deere 606 bush hog back together. Had new supports made (discontinued by Deere) and now putting it back together. I have lost the top flex link (W10261 discontinued) where the top link attaches to the bush hog. Anyone have a 606 that can measure this piece? It is shaped like...
I have a 955 tractor that will not start with the key anymore. A neighbor came over and jump it from the starter post to where the solenoid plugs in. It then fired right up. Key is in the run position and I turn it off with the key. I went and bought new ignition switch (32.00) from JD and...
I am looking for a Deere Buck 650 ext in JD Green. I believe that 06 was the only year they had the green and 650 together. I have tried all the local dealers with no luck. Anyone one know of and new old stock?
Thanks,
JT in NC
Just installed a power beyond kit on a 955 and now it drives slow. I did install the plug in the valve body which diverts the fluid through the jumper hose on the back. Any ideas before I take it to the dealer? My 855 acted just like this when I swapped the powerbeyond to the 955 and forgot...
I am looking at a diesel gator old style 6x4. The owner doesn't know how old is it? When did they start making the diesel gators? Main question is he said that it is overheating. The dealership told him that the belts were slipping. He got another gator and parked this one. Could this...
Anyone having problems with JD Parts. I log in and get a blank screen, nothing but a white screen. I have logged in on four different computers and no luck. I have emptied the my cookies and everything. Anyone else?
Thanks,
JT in NC
I have a JD 955 Hydro. I bought it used with a 7 backhoe. I did not check the lift before I bought it. It had the backhoe on and didn't cross my mind. When I move the lift lever it doesn't raise? I adjusted the wheel under the seat that controls the draft, but still nothing. I have changed...
I found a good deal on a 10A backhoe. It has the mounts for a JD 5000 series. My tractor is a 2240 (like a 2155 series) that Deere also made a mounting kit for back in the 80's. The mounting kit has been discontinued. The front will hook up to the 175 loader fine, but I need the rear part...
I am looking for the dimension on an I-Match hitch. I am going to set up my bagger for the 955, I need the width and height between the hooks. I have ordered it, but don't have one yet. Nobody stocks them here in NC!
JT
I have heard that deere has a new Imatch out with a single release handle. Does anyone have the part number? Dealer only has the two hand system.
Thanks,
JT
I bought a Kubota 4520A backhoe to put on my JD 955. I went to the dealership yesterday and looked at how they had them mounted. My backhoe is older, but it looks just like a Woods.( chain drive left /right swivel) I bought it used and it doesn't have any mounting hardware. What should I...