Recent content by radman1

My B2320 with la304 loader is in another town. I want to store it in a smaller enclosed cargo trailer for winter. The trailer is 12' according to its model but I measure the inside of trailer at just under 13'. Will it fit? Can someone measure their setup? Specs say tractor is 93.9" without 3...

Earlier thread discussed hooking up pto shaft with engine off vs running. How many unhook pto with engine off? I do not shut off the engine. The potential risk (although nearly nonexistent) is the same with the engine running.

2005 L4630 with 650 hrs, gst, front weights, TNT cylinders and r4 tires. Also has another spare set of hydraulics in the back. No fel. Tractor has sat outside and is sun faded but otherwise runs good. I looked at it 1 year ago and he wanted $12500. It has been intermittantly on CL for at least 1...

Here is a chance for someone to get a tractor that can go through the tough stuff. Any takers? It would be interesting to give it a try. 2010 - Kubota M126X MFWD Tracks Tractor - Loader - 125 HP - 64 Hrs.

I recently purchased a vacation/rental home in the Rocky Mountains. I have Verizon cell phone currently and the coverage is better at my primary residence than the other major competitor, ATT. However, in the mountains my Verizon service will not work in the house but works 100 feet away. ATT...

Have been contacted by company wanting to erect about 80, 2 megawatt turbines in our area. Towers would run in 2 lines about 3 miles apart, with about 40 towers each. Many irrigation pivots and the towers would be placed at the corners of the pivots to miss the circling pivots, roughly every 1/4...

Found a 4 in 1 bucket. Modified it to fit to fit a skid steer carrier attachment. Is it too big for my Toolcat?;) http://i345.photobucket.com/albums/p388/radman1photos/4in1bucket.jpg http://i345.photobucket.com/albums/p388/radman1photos/IMG00089-20101229-10241.jpg I believe it weighs nearly...

I had a kubota 3710 GST several years ago. Have gone to HST since then. Considering a Kubota 4630 GST -if I can get the price I want:thumbsup:. My 3710 did not shift well under load to a different gear. It would nearly stop, then shift and jerk forward. The old GST was 8 gears and the newer...

Looking at a used 2005 L4630 with HST and 600 hours. Very good overall condition. Has TNT, R4 tires, and front weights but no loader. Asking $14,500. Seems reasonable but I will buy if only a very good deal. If get it for $12,500 I might bite. This tractor is suppose to have the LA853 loader...

I am in the process of buying a compact loader in another state 1000 miles away from a Case construction dealer. Dealer has several stores in the Maryland area. Have talked to owner and salesman. I want to get a purchase agreement before I wire them the $$. Getting them to answer e-mails or...

Investigating the cost of shipping a compact wheel loader. 13,000 lbs, 19' long by 81" wide. 1,250 miles. Have listed with Uship and on Yesterdays Tractors. Any other suggestions or ideas? Getting bids of around $2100. Fair price? I have never purchased anything like this without seeing it. Has...

I currently have a 2006 Bobcat S300 with a/c, 2 speed, hydraulic bobtach and few other options. Very good condition, runs great, 3000 lb lift, 80 hp, 8500 lbs. I am considering buying a used compact wheel loader (CWL) instead of the SS. Have been looking at Case, CAT and NH. No JCB dealers in...

Does anyone have this kind of lift arm for their JD. Would this be used in place of a quick hitch? Can different balls in the lift arm be used for cat I vs cat 0 or cat II? Would the lift arm instead be used the bushings on implements to make it the same Cat III pin size? Ocassionally I would...

Sorry posted twice. Ignore this thread.

Does a FEL on a CUT lower the COG if FEL is lowered to near the ground with bucket? Is it better to mow hillsides with FEL and bucket on tractor than with FEL off? Could a bucket wider than the tires of a CUT help prevent a roll over if the bucket is near the ground?