Recent content by rcrcomputing

No one was hurt, which we've all probably been through as we get older. :) I'm here to tell you there is no comparison between the two.. In fact, it truly is JUST STUFF. Though admittedly it still sucks...

Close to Cleveland ok. About 30 miles Southwest of Tulsa

Another voice from Oklahoma... :) Total Loss, Barn, house, guest house, Commercial Zero turn, trailers, and the list goes on... Kioti tractor (may be savable) Yes, there was no stopping that windy wildfire that day.. A reminder to all, get "replacement" insurance, which I had on the house...

I have a 2003 260z mower. I have all this info, however, I'd like to get the spec info on the engine model cv740s. Is there a way to do this? Here's the other stuff I've come up with.. Mower - model 992047 serial 001595 Ariens Order Owners Manuals Owners Manual...

This is probably a bit of a repeat of this thread by KiotiKevin. http://www.tractorbynet.com/forums/kioti-owning-operating/307944-fluctuating-idle-stalling.html?highlight=idle+down Symtoms are the same. Will start, rev up, maybe run for 5 minutes fine or 1 minute fine or 20 minutes fine. Then...

I think I did pretty good tonight! 2004 gravely 260z Zero Turn w/hydraulic deck and lights with suspension system. 27 hp kohler 460 hours And a never used, 7 year old King Kutter disk 2750.00 I almost feel guilty!

I've about 1 - 1/2 acre area I'd like to add to my mowing. I've taken the hog over it, but did cut down a zillion small saplings in the 1 1/2" range. I have a bush hog, box blade with rippers, and tootbar and middlebuster. What do you guys recommend I do to get the sapling stumps up so I...

I am about to order the 26ga metal for my barn. I've a few questions I need you guys to wrestle with.. :) I'll give you a few specs "before" you ask. ha 30x40 4/12 Pitch 13' Side walls 10' opening on one end 20' opening on front. Truss's running the 30' Direction Gravel Floor The ridge cap...

I need an implement shed. Never to have concrete, never to have insulation. I'd like to go 30x30 or so.. I'll have about an 18' or so opening on the gable end. And a snow load of 10. I don't want to use truss's because I don't want to give up the head room. 26g tin (r-panel) 8 or 10' outside...

Guess that'd be true for tractors as well. Never really thought about it, but at the end of warranty, if you bought in the spring and you needed non-critical work done, you could hold off till winter instead of rushing to the dealer while still under warranty in the middle of work season..

While we post our forks, grapples, etc. I have come to absolutely love a cheap tool I made and thought you guys probably have something you've made or bought for very little that you find really useful. So here's mine. It's a t-post puller. I used it yesterday to pull some rebar pin 3' long...

While I need to get some better pictures, here's what I have for now. The only reason I'm posting about these forks is one unique reason. If I had it to do over again, I'd make them EXACTLY the same way. (Not all projects go that way.. ) :) The are light weight, but heavy enough for the 30hp...

What are the differances in the dk40se hst and the equivalent bobcat? I see the loaders are differant. What else? I've noticed some have had some problems with the bobcat being "under powered"?? Any of you had that with the dk40?

I need to say, I don't hold much hope. We put alot of time and care into our garden with raised beds. However, starting last years the gophers have found it. They really like cabbage the best, however, they are not nice about it and leave me nothing for me. :( I've tried traps, poisons, etc...

Here is a maintenance Chart from Kubota, I'm thinking to adapt it to a generic chart. I'd be interested in comments on the various items. And whether you agree with either or why you think they differ. BTW, I want to hear from everyone, I'm just quoting the ones I have data on. The goal, in...