When I tried the link you show above, I get a message saying that the file has been removed.
For now, I think I will do just as you said, leave that one relay out and operate the tractor as it starts and runs just fine with that one out. I still plan to check all the fuses just to see if any...
As a follow-up I found that the 12VDC at the injector pump fuel solenoid is present during key moved to the run position but not to the crank position. Then if the key is moved to the crank position, there is still 12VDC on the injector pump fuel solenoid. However as soon as the key is released...
The picture shown looks like a part I see that screws into what appears to be part of the engine block below the injector part. Is that perhaps the one you are describing?
On my 5105 I discovered that the engine starts but as soon as I release the key back to the run position the 12VDC goes...
I have a JD 5105 and recently the bushog attachment hit a stump and came to a dead stop while mowing. Since then the PTO shaft comes to a complete stop when grass of any significant amount is encountered. In the past the same amount of grass was never a problem. The Hydraulic fluid level is...
Zebrafive;
Thanks for the suggestion. It makes sense that the nuts would have to be tightened to compensate for wear. I have had this mowing attachment for around 17 years. The PTO shaft is the original to the unit.
Yesterday I took the shields off of the PTO shafts and cleaned and...
The original PTO shaft of my John Deere 613 rotary cutter (6ft. cut path) was bent due to an accident. I am trying to remove the PTO shaft end that attaches to the clutch at the gearbox. There is a locking pin on the shaft coming out of the gearbox, but removing the nut on one end does not allow...
DLTrekkers;
You wrote, "This pic is from a Same but the hidge is a Mita." Did you mean Same=sample? What is a hidge and a Mita?
I did visit my dealer and he says spool valve is likely stuck due to rust in the rockshaft assembly. He said that the original spool valve lacked any kind of plating...
This week I was ready to do some brush mowing and brought the JD 5105 out of the barn. I raised the mowing attachment with the 3-pt hitch control and backed out. When I tried to lower the mowing attachment it would not come down. I also noticed that it had raised the arms higher than before. I...
My John Deere 5105 with All-Wheel-Drive does not have the 3-Point hitch draft feature. I was looking though the owner's manual and the pictures which describe the draft feature versus the ones without the draft feature. Ones with the draft feature have two levers at the driver's right side to...
A few months ago I posted a thread about starting problems with my John Deere 5105 all-wheel drive tractor. We mistakenly had put some gasoline in the fuel tank. I finally determined what the problem was after repeated difficulty getting it to start and then drained the fuel tank and put new...
I have owned my John Deere 5105 for years and now am having a starting problem. Thanks to this forum and some other sources I have put together some information to help me diagnose the problem. I was looking for a schematic diagram of the starting system and learned that it is only available...
After changing the engine to transmission drive belt and repairing the steering gear arrangement on my Cub Cadet LT-1050 all appeared to be going OK. Today after about 10 minutes or less of mowing the unit blew the 20A fuse. This kills engine start as well as other things. A new fuse was...
I noticed a thread regarding deck belts jumping off the idler pulley. One comment mentioned the mulching function of the blades contributing to grass mat buildup above the blades. Are there any alternate blades that promote better ejection of cut grass from the right discharge duct and less mat...
On the Cub Cadet LT-1000 series lawn tractor/mowers the headlights are molded plastic lens types with 12V bulbs and sockets that insert from the backside. Is there a way to disassemble the front lens from the rear of the headlight housing to clean dust and dirt from the inside? Ideally I would...