Search results

Paul respectfully they aren’t good up here - this is the typical field

Reading between the lines for cash flow, you want to finance the equipment for the project vs cash or financing a decent used machine. I cannot comment on the Kioti $37K vs TYM $53K for 7 Years but IMO either rent a machine for a week, or buy a used machine and start the project. I know the...

Congrats on the new machine - did you negotiate any attachments and what was your final deal? All these attachments can be purchased later at a decent price.

Yes - 2Manyrocks, these "2 ton diesels" have an 80U (micron) in the tank and a spare too. I put magnets in the tank to collect any filings. Also interesting is the pump manufacturers indicate the 80U on the inlet is all that is necessary. I guess as long as one changes the fluid these will run...

Yes Tex, that very much is the case with me - the Kubota has a BH but the mini now does the lifting and rock moving as the helper into the Kubota bucket. It's handy having these tools or toys as my wife calls them. Then it's a Post hole auger, a log holder, a crane etc.

Honestly, they don't need the motor protectors - they were made for the smaller gas units to prevent the bending of the side rails which on the early machines was an issue. Secondary is the motor protection, which if you are deep in rocks and stumps then they will offer some protection. The...

I suggested the Kubota L47TLB. It's a tough machine. The new one is $70K, but that one is $42K, a good deal. They run for 4000 hours, so it's barely broken in at 500 hours. - On your lake side well - I installed a well on our house on a lake in MA in 1980 20' off the lake after our sand point...

They are fine - well built, everything works as it should. The Typhon XVIII is made by Hightop and has the 180MM tracks and Kubota 722 14-15HP engine. The Typhon XIX is made by Vote, and has 230 MM tracks, and a Kubota 902 16 HP or so engine. Also the XIX has a better fit and finish and has...

Thanks for the pics - my machine had a similar thumb and we have a lot of rocks and boulders and the tines were flexing too much for my liking so added two pieces of 3/8" x 3" steel braces between the tines - but still allow for clearing the boom and mating to the bucket properly.

It's the Kubota TLB Series - Tractor - Loader - Backhoe - Specifically made for construction and commercial use with a very rugged frame and underframe protection - these machines are pretty indestructible in most applications. For the rocks and rough ground we have in NE it's one of the best...

You could consider this Kubota L47 with 516 hours and $42K which is built for what you are going to do in the woods - these are tough machines and you can add a cab if you need to.

Appears you are in Maine, and have lots of rocks like we do here in NH. Consider getting a full sized used BH 4WD - Case 580, JD 410, Cat 416, Ford 575 or similar - they are 14-16K lbs so can move trees and rocks. They can be found with 3000 hrs for $25-35K then spend the other $30K on a decent...

These are great prices and when i looked at the 2850/3000 unit it was unavailable yesterday, but I checked this morning and bought one - for the portability aspect mainly. For $249 it's hard to beat this deal for an inverter generator and has an Eco mode!

Diesel on NH coast is $3.39 and regular is $2.55 - this summer both were almost $1 more.

The shavings could have been the hydraulic cylinder scoring (without seals) or just left over from the manufacturing process. Most machines have an initial 50 hour service interval where all oils and filters are changed, Then the question is why would they put the old oil back in? As others...

Post some pictures of your new digger and also some of your larger ones. My neighbor has the Komatsu D21 dozer 1300 hrs - its a very nice machine great for grading and small enough to tow with a pickup. Surprised you didn't spring for a diesel Mini ex with pilot controls - they are 9-10K now...

Rscotty - as a former farm boy, the old tractors had small front wheels for visibility to see the ground for row crops/plow furrow, and big rears were for traction and pulling. Also for loader frame clearance etc, the smaller wheels are better. But to your point, I can envision a better...

So Tharg there are a lot of 2WD older tractors for sale near Coventry but very few with loaders but here is a nice Kubota with loader 37 HP and 65 hours that would do nicely for you. But the price is not listed and it does not have a QA bucket (key for changing implements like pallet fortks...

Eddie, I'd say that's about 25* - definitely beyond my comfort zone! I have had the tiltmeter since 2003 and don't often need it - my pucker factor is about 15-17* and mostly by the "seat of the pants" method, e.g. when it feels too steep I'm focused on getting out safely than looking at the...

Tharg - where are you located in the UK - nearest larger city? The north and highlands gets some snow, then the south, Devon/Cornwall region little. Assume rolling hills and pasture land?

Excellent video - Merry Merry Christmas to all, we miss Harv!

Thanks - the pin was indeed bent, and the holes second one in Left and Right are elongated - essentially the webbing collapsed making the last hole an oval. Was able to get the pin straightened and free, and then found the grease fitting on the center pin - never was used :-) so now the plow...

Merry Christmas to you and your family goats, dogs and the very best for your years on the farm - emojis excepted!

Cold Microbes! It was 3* yesterday and today its a toasty 33* so yes they might wake up as it warms up. I used to tarp the piles and they would get to 140F

The big pile is this year then last year next to it which I will use next spring

I mulch the leaves with Gator blades and collect them with the TracVac. Usually, 20-24 loads a season make a 16-yard pile that composts down to maybe 5-6 yards in two years. Then, I use that for top dressing the beds and yard. Mostly red and white oak trees - big leaves that need to be...

It is live and not a diverter type. It has a two-button switch that activates a dual-port cylinder. I installed it on my Kubota B21, and it works well.

Hi John, Just looking at the Digmaster web site - they are a small group and "relabel" them - I would stay away. On the other hand, Infront is a larger group and does most of the assembly and I like the design better too. I also have heard others that have this brand and they make a good...

Yes, Mike agreed the B21 is 90% of the B26 thats why I decided to modify existing. Added Kubota B2673 Snowplow this week and found it locally in NH for a decent price $1K - no hydraulics - manual adjust, but I have sourced the cylinder and hoses. Had the first run today with a light snowfall...

Yes I have the Typhon Terror XVIII made by Hightop - I got rid of the Terror logo the day it came home. Also look at the Terror XIX - its the same size but has the Kubota 902 engine and 230MM tracks. They are decent machines - fit and finish is 6-7 of 10, and function is 8 of 10 compared to my...

When it comes to name brands of Chinese-made machines, only a few actually "make" them—the rest are assembled from purchased parts. Companies like Hightop, Vote, Shantui etc. make them, and then resellers put their labels on them. The gas engine machines without pilot controls are warm and loud...

The unit mentioned above CFG STE 35 SR has a hydraulic flow of 87 LPM or 23 GPM and a digging force of 24KN or 5400Lbs. My Kubota B21 has a digging force of around 3200 lbs or 14 KN so this machine was the better step up - But I don't need it - I "wanted it" and it didn't fit in my barn (too...

In my opinion this 6K machine is one of the best for the money at $22K 2.8 Ton, Mini Excavator w/ Diesel Engine | CFG-STE35SR It's built by Shantui who makes this machine for Kobelco also, and Shantui make many other bigger machines - excavators and dozers. If has a Yanmar engine and two...

Yes, definitely get Pilot controls (thats all these 1.8T diesels have anyway). On my updates - spent about $600 total. - Added a Tiny Tach - as I like knowing the RPM $100 - Reinforced the thumb - welded 2 - 3" wide gussets inside the thumb - Added a rear hitch plate and motor protector $150 -...

I got the Chinese Mini Ex Typhon 18 with the Kubota Diesel - weights in around 3500 lbs - no cab with Pilot controls. A cab is really tight on these small machines and hot in summer. I have also switched the travel around sticks now to make more leg room (pics are before) as im 6-3 240 lbs...

Matt - very true - on FBM I see the 1.8T Kubota Diesel new locally here for $14-15K. I got my Typhon 1.8T kubota 722 engine with rock bucket and quick attach for $11K in May 2024 now they are under $10K and less at auction.

That appears to be a split rim and tube setup which makes sense for these small wheels/tires. The smaller diameter can be real PIA to get off the rims, then reseated if tubeless, but you should not have an issue with the split rim/tube setup. But, I agree, replacing them with a solid tire is...

Get a set of pallet forks for the 3 PT on your JD 730 - it has a 3PT correct? Then put the snowblower on a pallet or a pallet with larger 6" dolly wheels. You can also store your other stuff on pallets too - makes it easier to move. I am in the thinking stage of a storage rack to store 2 FEL...

JWK - I have dug foundations, dug up septic lines with my B21 and the slab on grade pad for my barn with 18x24" trench all around and poured as one with rebar. We have ledge and glacial till here on the coast - rocks 2' to 3'. I bought a "2 ton" diesel mini excavator which weights in at 3500LB...

Mike - I am keeping mine - it now has QA FEL, Pallet Forks, 3rd function, Hydraulic Thumb, and a Grapple to help me out. Then added new 3PT adjustable arms to replace the old bent screw type makes putting on things a lot easier.

Doing it alone is 3X harder - if you had someone to move the track and another guiding the track it's a lot easier - but patience and persistence got it done - Good Job!

I have bought and sold stuff on CL and FBM, and most of the time there are no "deals" as prices are 20% or so less than new for what I wanted. For example, I converted the pin on bucket with a QA and added the third function. So was looking for forks and a lightweight grapple for my B21. All...

I use a tow behind lawn detacher in the spring to pull up dead grass and it also rakes up the small loose sticks too. Mine is 42" "brinly" I tow behind the garden tractor - but here's one for a 3 PT and inexpensive too! VEVOR Tow Behind Landscape Rake, 72" Tow Dethatcher with 32 Steel Tines...

Restored a L175 DT with a BH and Loader in 1997 - the loader hydraulic was run from a front pump on the engine. Removed the loader and BH and got them sandblasted and painted, then replaced all the hydraulic lines etc. Rims were rusted from calcium in tires had to weld rims. was a 6 month...

For those who have a front spring-suspension seat on their Kubota, here is an easy update. My 240LB would bottom out the front seat suspension springs against the rubber bumpers inside the springs when just sitting in it. I looked at options to replace the seat but it's a swivel seat for BH use...

We have 7.2KW (25 LG Neon 300W) panels on the garage (separate service entrance) since December 2014 and we just hit 77MW (average 7700KWH/Year) with net metering we over-generate but they pay us the current rate for excess power. Payments are taxable over $600 a year - they send us a 1099...

Locoweed, Can you provide any info on these external antennas? I installed the Orbi750 series Mesh system with 3 satelites also have a Docsis 3.1 new modem on Comcast 1Gig internet. Mine have been somewhat erratic dropping signal etc and i'm looking ti boost the signal from the main router...

This is my 24x36 two story barn in 2010 (built in 2000) then full in 2024 and I have been cleaning out - gave away 2 radial arm saws, sold 60" snowblower, sold the 1864 Cub Cadet Garden tractor. Was going to put an 8x36 extension on the back but started cleaning out and getting rid of stuff...

Welcome to TBN and no shortage of opinions here either!

Maybe find a small used harrow or disc and pull it behind your JD 1445 - it should have enough HP to pull a small 5' or so implement.

You can do most of the engine work without "splitting" the tractor - as splitting is done to replace the clutch or hydo drive, seals etc. But if you want to split it - get some jack stands, make up a cradle to support the front or back with one side being able to roll away. Also if you have...

Oosik, Interesting point - never thought about that but appears by this map that its mostly in the western states - the east coast states have only a few cases up through 2022 - and NH for instance had 1

I have two Sthil BP Sprayer/Blower 420 and 450 for mosquito fogging and leaf cleanup, then a very handy and light 10 LB HItachi 25CC (now Metabo) blower thats my "go to" for quick cleanup, blowing out the zero turn, light leaf cleanup. Robot or human? It's 6 years old and still fires up...

It appears the fan is separate from the motor so why not just buy this one and use your metal fan? Whirlpool GS6SHEXNB00 Refrigerator Condenser Fan Motor Kit

Here is a lower cost option for $239 - no side covers tho but better than nothing. Or you can buy the metal mesh and build one...

I would not attempt to tow in that manner - too many things to go wrong - connecting to tow vehicle, lack of control and tracking the wheels, then no brakes, then wear and tear on the front end parts. Why not just drive it - 11 MPH is top speed is 18KM/hour or rent a proper trailer - they are...

Yes it looks a bit rough but if you dont mind working on things it's a decent deal. if on the other hand you can find decent backhoe's for 15-20K that are newer and have 4WD and power steering. Here's on in MA 登录 Facebook

There are several good looking B26 in PA - one in Pine Grove with 680 hours on FB Marketplace for $29K. I was looking to upgrade from my B21 with 750 hours but decided to keep it and add the QA bucket, 3rd function and Hydraulic thumb These 4000 LB TLB can do a lot of work and will fit your...

List it here on TBN - its free Classifieds Then Facebook Marketplace or Craigslist - I have had good luck with both sites.

I'd say your in the right ballpark price-wise - the trailer seems a bit low at $1500 but assume its a 7000 lb or better. Here's a link to auction results - which tend to run lower (due to fees/commissions which can add $700-1500 to the cost. There is a for sale section here on TBN you can...

After reading about tireject here, I decided to give it a try. First on a hand truck with one tire bad tire bead would go flat in two days - tried cleaning the rim and tire with cleaner no luck, Put in 3 oz tireject it has been holding air for a over a month. Next was my B21 left front R4...

Finally got around to working on my 15 YO leaking Emglo dual tank air compressor - it was the drain valve sticking - a simple fix. Then it would not shut off and had a bad gauge, replaced gauge and it would build pressure slowly - hmm. Took the switch cover off and switch was arcing when running...

Glad it was easy - keep on tractorjng !and post some pics of your b7800 too

Another suggestion is do a search on B7800 no start condition here on TBN or Google..

The clicking on the right side is the fuel shut off solenoid engaging which is normal. Are all your safety switches good- clutch, PTO, seat etc?. Do you have the normal lights on the dash for pre-heat on the glow plugs? If not check the ground strap connection at the frame rail, also, get a...

We bought a kitchenaid made in Indiana in 2017 French door, double freezer drawer, ice / water in the door. The first one had issues at 6 months (ice maker) would not make ice - ultimately they replaced it with another one - that one lasted for 9 months same issue. We got a credit that one and...

I passed up a 2600 hr Cat 303.5 Cab at 9200 lbs as it was too big for what I needed and the attachments were very expensive. I did get a $11K 2 Ton China Mini Ex with Kubota engine instead (with a rock bucket, Auger, Tiling grading bucket)- its the helping hand loading 2' rocks into the FEL...

That's not great news - that means it is either a line leak in the pipe to the well, or a bad check valve on the top of the pump. You could install a check valve at the tank which would stop the backflow from the tank if you don't want to pull the pump now. Otherwise it will continue to cycle...

It sounds like you have a submersible pump and a tank tee with the gauge and bladder tank. Definitely get a new low-pressure cutout switch 30/50 or 40/60, and also check the pipe to the switch (you mentioned incompatible metal) - it should be 1/4" brass or a copper line with ferrules. If it's a...

How did you make out in your tractor search this weekend? Was the kubota 7510 a buy or pass? Then tym or other Machines peak your interest?

As posted before the local 230 hr Kubota B7510 with books/manuals was well cared for and at $15K with FEL, 48" Brush hog, a rear blade is a great start. If one wants to upgrade to a bigger unit in the future there's minimal cost/loss. Its bigger than the Kubota BX and smaller than the L, so a...

Well nothing is leaking up in the boom - its at the swivel point - covered in the nylon wrap - need to cut that off and see which hose is bad - but I just went ahead and ordered all the hoses now - once and done.

My B21 BH Sprung a leak today somewhere in the BH boom - I have yet to determine which hose is leaking (waiting for my neighbor to come by to look inside while I cycle the dipper and bucket to ID the leaking one). But just looking online at Messicks and Eagle, Kubota wants $900. now for 6...

Have you tried heating the block - is it AL if so, it should expand faster than the fittings. Then can you get a round jaw set of pliers or vise grips on the bulge or the ribs to add some more leverage along with the wrench? It could be that connection to the nut that's tight?

Yes - Runner get the 19" here's a set on Amazon for $66. Amazon.com Just make sure they are 19", then when you install them do a "dry run" rotating the blades by hand to make sure the tips don't hit - BEFORE you turn it on. I put gators on the neighbor's ferris 48" that were supposed to fit -...

The 18 1/2 should fit fine - its only an 1/8" - also the measurement is corner to corner across the blade on the diagonal across the center hole. It doesn't hurt to buy a set to compare and then run them - it's a $60 investment. 18.5" x 3 = 55.5" so you have overlap either way. If your blades...

Agree with John - get an inexpensive hoop shed (Harbor Freight etc) 12x20 and keep it covered out of the elements. Even a lean-to or carport so its protected. Tarps are not great - critters like to make nests, they trap water etc. - an open lean-to or carport lets air thru and less critters...

You can get the Gator 596-333 18 1/2" here that will fit your machine here 596-333 - BLADE CUB CADET GATOR G5 18-1/ - OREGON Authentic Part The only concern is your blades have a cup at the end (to throw the grass) but the gators are great blades - I have them on my ferris and they are great...

I put my "tools box" behind the seat - has most everything I need to fix in it - added a bracket and adhesive foam so it sits tight.

If it comes down to it I have a quote from a pole barn company to put that up. They are Mennonite builders whose word actually means something, not like all these others who have been ghosting me. If by the end of 2024 if my GC is still having issues getting going, I'll pull the trigger on...

Is the goal to get the perma columns in, with frame, roof, and sides in before winter? Then wiring/plumbing in over the winter, and pour concrete and finish the inside next year?

Made a plywood sandwich to hold the saw and attached a 7MM ammo box to the back side to hold 20' of chain and misc tools. As to gas and oil, those go behind the seat next to the BH console.

Thank you Rscotty - its a work in progress, and yes the B21 has two hydraulic filters - one large 8" Long and one small 5", then the suction side screen inside the sump. I heard from ATI this AM that the TL2156 HD round back bucket is "uncommon" and that the QA plate would need modification...

Thanks for the kind words and its stored inside all the time and grease/oil and filter done per Kubota specs, The step into the deck wasn't on the B21's and as far as the ATI Tach All - I am also concerned about the round back HD bucket I have and how a flat plate is going to mount. I have...

Here’s some pictures of my b21 today- it’s not clean but pretty good shape for 23 years and 750 hours - and I know the maintenance and what it needs - two hyd cylinder seal kits when it gets bad enough- just a few drips when sitting for a week. Ordered the ati quick attach and plate today 1400...

Well suffice it to say someone else wants this unit more than I do - I bid to $28K - my top end and it looks like it will fetch $32-34K or more. This is before the auction starts and the bidders are on site etc. So, some mods are in my future with the B21 - the QA is first. Looking at the...

New ones range from $44-52K depending on the options from what I have seen - I haven't visited the "build my Kubota" site recently. At the same time looking at the ATI Tach-All QA set up for my B21 - TL421 loader and the weld-on plate for the bucket is $1400 including shipping. Does anyone...

Update - raised my bid and was outbid in an hour - so will raise the bid again and if it goes above my max intent will likely keep my B21. Also, I heard back from a dealer that the B26 is under warranty until the end of October 2024 so that is peace of mind in case of any issues.

Smokey it comes down to 1) I know what I have / what it needs (a few seals on cylinders probably $500. 2) I can add the QA setup for $12-1300. What I cannot get is 4-5 more HP and 300lbs of lift capacity from my B21. Also eventually add the third function valve, a plow, and a grapple...

So the bh qa is a new bucket too it would appear - will need to see the $ tag on that -probably better part of $1k thanks for all the replies too - now will see what it goes for - if it’s a good price I’ll probably get it then sell my b21 - don’t have room for two.

Thanks Cal and Smokeydog - for the soot, oil and missing pieces. The oil maybe no big deal but it shows lack of maintenance but its a low hour machine so likely OK, Yes, I also searched the photos for the light arms but could not find them. Thanks for catching the missing floor plate - I take...

So Cal you are saying this has sat idling/running for long periods with the loader down, maybe doing BH work? So this amount of soot is normal on the FEL trame? BTW this B26 is more a want than a need - I want 300 lbs more lift capacity and 4-5 more HP and a 20-year newer machine, but don't...

HI all. Have a B21 for 21 years bought it new, now 750 hours - runs well, I just did the Hyd thumb last year - works great, the things lacking are a QA bucket for forks and lift capacity. I can add the QA bucket for $1500 and then I want QA fork set up too. Been casually looking for a B26...

Yep - nasty ground yellow jackets that usually fly faster than I can run - have hit many of these over the years weed trimming and mowing - you're lucky to have just 3 stings. I wait till dark and pour a half gallon or so mix of permethrin and water in the hole then toss a half bucket of dirt...

The thumb on the 4000Lb machines tuck pretty close to the boom, but the tines support were questionable so I welded 3/8" x 3" steel between the tines at the back and near the ends. I have picked / moved 20"+ size rocks with no issue or bending.

Wow - looking good - looking forward to this build - putting in forms for the stone entrance is treally attention to detail!

Here’s a brand new one. As big as a large square baler is, it’s got fragile parts in some places. A baler knotter is like a large industrial sewing/knitting machine with some of the most complex mechanics in a very tough environment. Kudo's to getting it running again. We made 3000 small...

They commonly run with the door and front window latched open then the right side window opens too, and it should have a fan or you can add one. Really depends on your climate - if in the south and southwest, yes AC is probably necessary, if more temperate areas it's a nice to have. As you...

You're correct - I was looking at the picture on the landing page https://eg4electronics.com/nitropack_static/SbBGCpCePLcXaRGwuXIMyVzcABRhrYXs/assets/images/optimized/rev-a0f0e43/eg4electronics.com/wp-content/uploads/2024/04/EG4%C2%AE-BrightMount-Solar-Panel-Ground-Mount-Rack.webp showing 8...

Our roof mount array is covered as well under the home insurance - no additional premium cost. On the EG4 mounts why not do an 8 panel array as show in the installation manual and do 3 x 8 with 24 panels per with 12 concrete piers - its two more holes in the ground (vs 10 concrete piers) for...

NortracNY - we on TBN analyze stuff (to death sometimes) and make decisions based on facts and real world user experience - initial cost, ROI, quality, maintenance etc. Then typically use spreadsheets and input these variables to look at all the options and costs and benefits associated So the...

I didnt buy a Cat 303.5 (8K machine) with 2500 hrs in 2022 for $27K - one owner well maintained machine. I couldn't justify the purchase for 20-30 hrs i might use it in a year as I have the Kubota BH too, So this year looked at two options - the 1.8 Ton Terror (3600 lbs) $11K with Kubota...

Vince - agreed the "2 ton" China Minis may be 3000-3400 Lb bucket force, which is about the same as my Kubota B21 4000 Lb machine - but the 23 YO Kubota has a better hydraulic system and controls than my 2024 1.8 ton machine. Ya get what you pay for. They both have a niche and value to have -...

No - check the first link posted - it’s 5500$ for the one ton machine with gas engine and yes - the 2 ton machine with diesel is twice the price but a lot more machine for the money.

All over the place - Ebay - auctions - heres' one FREE SHIP Mini Excavator 1 Ton Digger 13.5hp Gas Tracked Crawler B&S EPA Engine | eBay Here's another one 2 Ton for $11K...

If you are still on the fence about this - here is the unit I would buy vs the Hightop - its made by Vote - and has a better fit and finish with the Kubota 902 diesel and 230MM tracks already, And the price is good $11,200 FREE SHIPPING NEW 1.8 Ton New Mini Excavator, KUBOTA D902 Diesel Engine...

Max 24 - yes this is what I recall now 10 years later .25% per year - I thought it was 2% but as mentioned in 10 years we have not seen any appreciable drop of generation with the LG 300 Mono panels. These panels were the best you could buy in 2014 and also you are correct if you buy a lower...

I agree with reduction of usage as well - insulation, more efficient heat/air conditioning etc. As far as the original question about the longevity and loss of efficiency over time, our LG Panels have been installed nearly 10 years and they are as efficient today as when new - LG claims like...

Here is a view by month and in 2021 we took down a lot of pine trees and this increased the production by nearly 1000KWH per year. Also for your install do you have shading - if you don't then the per panel optimizers aren't that necessary. Then on system sizing - I think 6 arrays vs the 5...

Hi LD, December 2014 Installed 24 LG Mono Panels 300 W with Solar Edge inverters for 7,2KW Garage Roof Mount – 38* angle, 190* south facing, Latitude 42* Cost installed $26K, State credit $4000 Federal Credit $8500 net cost $13,500 ROI was 8.5 years – electric cost .18 KWH when we installed...

For the 8-9K you are going to invest in a BH its better to get a mini excavator - you can get the 1 Ton units for $5-6K but the better machine is the 2 ton with diesel for $11-12K.

Agreed at $850 for a new one you can likely get 100$ of steel and weld on - I presume yours go thru the bucket teeth but should have enough clearance to weld new ones on the sides?

Yes - as I said it's more a want than a need for me - at 12K though its nice to have - also think about the reach as being 9' in all directions around the machine. Then the breakout is nearly double your machine..

If they are copper, the scrap value could be good, otherwise if they are aluminum I would cut the ends 6" below ground and leave them.

I measured the reach - its 110" and digging force with the bucket is 3400 Lbs vs 2000 on your Max - you can see the specs below. There are other things to consider too - the 360 rotation and digging is much easier then the bucket options you can add for little $ like screening and tilting bucket...

See post 104 the 7” lug tracks imprint the lawn and rip it up - the diamond tracks are 9” so 30% more ground contact and are made for traversing lawns and dirt and are a smoother ride 8 hours total - just getting started using it - once mods were done I have a backhoe on my b21 too so this is...

Has anyone added a Tiny Tach Diesel Tiny-Tach | Design Technology, Inc., Home of Tiny-Tach to their machines? If so do you have any report or feedback on the performance of these units? Thanks

One other note in the tracks - there’s a spring 3/8” thick x 2” around in the adjustment mechanism that holds the tension on the tracks - so unless you’re doing something aggressive or get rocks in the drive sprocket they won’t come off - also checked the pulleys and bearings all tight - no...

Got the new tracks installed - much smoother ride and doesn’t leave divots on the lawn either That’s a friend of mine testing it out he wants one now - but a bigger one Modified the thumb /tilt bucket aluminum foot pedal - drilled and tapped a 5/16 bolt and nut thru the swivel portion so...

Very nicely graded and it looks really good! The pictures are great but its hard to capture the elevation or show how and how much you have built up the site. As it looks like the piles are 4-5' high then the final grade from the drive to the berm of the building is 2-3' elevation?

The 180x72x41 tracks on these tend to tear up the lawn even when trying the lift and move method. Granted I am not proficient yet in driving this either, but I wanted a wider track (230 MM) and something better on the lawn. I found these on ebay and ordered two NEW 230x72x41 Track Diamond Back...

Space in the barn - then the b21 does almost everything I need - the mini ex was a “want” not a need. I almost and should have bought a 2009 cat 303.5 in December 2022 with 2500 hrs for $27k from a guy that bought it new and took care of it- I didn’t buy it as I thought it was more than I...

Agreed - I loaded and moved 5 kubota bucket loads of 20-24” rocks today with the mini ex and it worked great! Finally can use the mini to be the helper to the tlb.

Success!! Swapped lines 3&6 on boom to 4 & 5 on stick and now it runs in backhoe mode - that was easy!

Yes DF - I remember when you got the B20 basket case and restored it - that was decades ago! Yes I still have my B21 760 hours now in 23 years and still doing great. Wanted a mini ex as a supporting cast to load rocks and clear some stuff out. But on to the Mini and hoses. I took off the...

The two pilot control "sticks" all have 4-5 small hoses each that connect to proportioning valve blocks on the main valve assembly - it will be easier to change them at the "sticks" rather than on the main valve body as its very tittle line clearance to move them around. I need to figure out...

No issues at all with the machine - its the operator! I spent yesterday morning "learning the controls" turning over my compost pile - as I am used to my Kubota BH for 20 years - I didnt think it would be hard but it's definitely a challenge. So after getting frustrated I wanted to see if...

Finally got all the bits and pieces to finish the mods this week. - Added the motor brace and hitch plate - welded on - the drive motor mounts are very robust on this machine - I dont think it was needed but its done now. Was going to add plate over the lines but decided to see how this works...

That corner in front of your lumber kiln looks about 3/4" low :-) Very nIce work and great attention to detail! As they say a good foundation is key to any building (or business) for that matter.

Maybe roundup - but spraying that with the mower running would get it everywhere and on the blades, wheels and tires tracking it on the lawn. Not a good idea - It might work if you are just riding and not mowing. I have my Stihl backpack fogger mounted on the back of my cub cadet garden...

Agree that's a nice patio/fireplace install. As far as frost heave not a lot you can do as it goes down 3-4'. As long as you have a 6" or so gravel base, then 2" compacted tillings/stone dust and sand on top it's about all you can do. Appears he excavated about a foot or so.. It will freeze...

Still a work in progress here - waiting for the correct fittings to connect the Tilting grading bucket with the 14MM Hyd QDs I bought based on the Typhon suggestion (should have bought 16MM not 14) Then have the drive motor protection from Central Digger supply on the way - not that this...

No manure has more nitrogen too - anything like leaves, straw, composted wood chips, dirt, etc. If you dont have any go buy a bale or two of mulch hay (they sell at farm stores etc) and mix it in.

No - its stable 44" wide tracks x 55" long on the ground and there is a new version of this one made by VOTE Machinery and you can likely get this for around $11,500 and ask to include a quick connect and like a ditch bucket for $400. FREE SHIPPING NEW 1.8 Ton New Mini Excavator, KUBOTA D902...

I measured to the top of the ROPS under the canopy and its 85 1/2" so too tall for 84" door height - lowering by 5-6" would not impact sitting in the seat much but would lower the height to get in/out.

No - its 89" to the top of the canopy - you can remove the canopy and that might just make it (4 bolts) and its a molded / extruded plastic top about 5" thickness so not too heavy, I can measure mine later tonight. Or there are 4 steel posts 1 1/2" as the ROPS and you could cut those down by...

Thats a pretty slick cutter - like how it defines the curve.

Yes they have a 80 micron filter in the tank and oil cooling radiator - half the raditor is engine cooling and the other half is oil cooling. The kubota engine runs smooth and quiet, pilot controls work well and everything is tight - but the doors/hinges and little things need adjustment but...

Took a few more pics today - got the QD and Tilting bucket installed, replaced the needle grease zerks with brass ones, and got it parked in the barn now so I can access all the machines. Still in clean up going over the machine and review/tightening everything, etc. A few findings - the tilt...

Hi Drawthree - I left for FL on the day it arrived and just got back Tuesday AM. All I have done so far is move it to the barn and start to plan modifications. - First impression overall looks real good for the $$ - the Terror stickers were peeling so I no longer have a Terror - now its just an...

Like it says in my profile- coast of nh - north of Boston if you need a reference The driver was from Pa so I think they bring them into east and west coast ports

Well I got a note from Chris to contact the delivery dispatcher this morning and before I could call them the machine was in the driveway-l m on a trip now too so driver unloaded and drove up driveway- Liam the driver was a very nice guy

Will do - also can you look at your tracks and confirm the size ? 230x72x41 Also you mentioned 2 speed when you lift the lockout it is faster ?

looks sharp - nicely done!

Thanks sheder - I am 6'3 - 240 and size 13 shoe and have similar concerns on pedals. I am looking at the folding SST or AL pedals they have for min ex's in lieu of the large fixed pedals on these machines - only $30 a piece. I plan to do other mods too - adding the brace and covers between the...

Excellent news on your units arrival Sheder and thanks for the pictures - how is the fit and finish overall? Also I was under the impression that it was two speed too based on what Chirs said, and by the manual and other info on the FB mini ex group. I placed my order May 3 and Chris (USA...

The irrigation solenoid valves are finicky as any sediment will cause them to stick and not close. Our 10 zone system constantly needed maintenance until I installed a large GE 1" filter - since then not one sticking valve in 10 years. Our install was 5 heads per zone, and pump was cycling off...

Sheder indicated Wisconsin in one of his posts - and he should be seeing it in the next week. For those that ordered early May. mid June is the targeted delivery date. I'm sure there is quite a bit of logistics wrangling to get these machines delivered across the country once they land here in a...

Sheder take some pics when you get it - and let us know how the delivery goes.

Hi Winter deere - I have a similar Ferris (2010 model IS 2000) with 25 HP Kawasaki FH751 with full suspension and going over bumps and dips, the deck moves with the suspension and does not scalp. But yes, some areas (rock outcrops or high roots) I use the deck lift pedal only a few places and...

Venture to say roughly half - I went from 2 hours to 1 or a little more if I double cut some heavy areas - I don't mulch but using Gator G6 blades does a nice job.

After every mowing I blow out the deck and everything with a leaf blower before putting in the barn. Keeps it cleaner. I don't mow when wet so don't get grass build up,and leaves and sticks in the fall tend to clean the underside of the deck. Average about 35 hours a year - so do two blade...

Agree with John - a track saw is for cutting larger sheet stock - I use a skil saw (Makita) for this and bought a saw guide $26 from HD for cutting larger stuff (countertops, plywood etc) Empire 98 in. Cutting Guide E902 - The Home Depot Then I got a used portable table saw 10" blade for $25...

Dig up the dirt, mix with some more dirt and spread it like you would spread fertilizer. Or if you compost leaves and stuff, add it to the pile - it will speed up the process and make good compost.

JFS - I bought the same debris forks 48" when Titan had a sale on these a few years ago. I haven't used my pallet forks much since I got these. Easily allows me to carry 3x the capacity of brush and stuff - also good for picking up logs - they are very sturdy and well built, easy on/off - 2-3...

Hi Sheder and Mej, what delivery timeline have they given you for your Typhon 4K machine? I heard from Chris last Friday mine is going to be here mid June - June 12-16 range at this point. I'm probably at the end of the delivery run West >East - being in NH unless they bring them in to the...

So, you bought an ISX2200 in June 2022 and another new one today? I guess you got a good trade - or why did you get another new one after only two years? My IS2000 25HP Kawasaki (2010 model) with 470 hours is still running great - square front 52" deck and I run gator blades.

Ouch - i take it thats the hydro cooling fan that found a stick. Not fun to change I bet. Sorry for your misfortune. We had a microburst go through our property in 2006 - sheared 100' pine trees off and dropped some other big oaks. Had a logger in to clear some trees and clean up the mess and...

LS lists a 36" bucket for the 1100 BH, and the 35HP tractor with FEL and BH is at least 4500 lbs so should handle this bucket. I dig and lift rocks 300LB + and lift logs - 7-800lbs to cut them up and or carry them with my little TLB BH without issue. It weighs 4000Lb with digging bucket force...

It's a 25MM x 195.5 Long Pin with grease fitting - so 1" x 8" long and you will need to measure between your bucket ears for width and between the pins to get the pitch. Probably around 4" between ears, and 5 to 6" center to center pins.

I have several multimeters but my go to is my Amprobe - digital clamp on - also have the old style analog amprobe unit. Simple to use and reliable...

10% off been up there for 5 months or more. I looked at and made an offer on ebay - they countered at $17,5 but the thing is, this 2.5 ton has bigger attachments - auger, quick hitch, tilting bucket are another $7K making it a $24K+ purchase. This is more of a "want" than a need so the...

Walleye Joe - no to lifting 3K maybe 1200-1500 lbs max close up and near the ground - and mine wont be here for another 4-5 weeks but there is a quite a bit of info if you look up Hightop HT18 who makes these. The machines weigh total about 3500-3600 lbs so you can expect them to lift about...

Spending the money now for a resurvey and rezoning would be best. Rarely do buyers have the funds or desire to buy more land when they first buy a new property, or they want it for a song. Divide and sell, or divide and hold is up to your personal needs financially. They don.t make any more...

So you know you're going to sell and downsize a bit, and you have 34 acres, and you don't want to build on the 17 acre parcel due to egress / access. You also acquired this after the house purchase so can take that cost basis against the gains. Consider separating the parcels into two lots...

I just pulled the trigger on a Terror XVIII 4000LB from USAExcavator yesterday for $11200 including the quick hitch and screening bucket - thought that was a good deal. I tried to get a deal on the Typhon X2 machine a 5000LB unit but the attachments were expensive. Havent gotten delivery info...

There are a number of these Typhon and 4K machines/owners reviews on FB Chinese Excavators And Mini Skids - Mods And Reviews Also most of these machines are built with standard materials and you can get replacement parts if needed with US parts. You should plan to add a drive motor protector...

They have inexpensive $100 or less for 4 replacement suspension spring assemblies on Amazon. I would say if you can get a clone/replacement for under $100 for 4, go for it. But $200 seems like a lot when the problem could be the drum bearing etc as others have indicated.

Larry, I believe the tolerances are such that a 1" bushing will fit inside a 1" bearing. I just did several projects with metal sleeves/bushings on cylinders with 3/4" 1" and 1.5" and they fit together just tine. If you have a TSC or similar close by these are $3.79 each...

HI Larry, Just go to TSC (Tractor Supply) and get a 3/4 to 1" bushing for $3 if your not doing over the road use.

Ha funny one WOIC123 - I grew up since 8 yrs old running a JD 420 with a 2 bottom plow, allis combine, a 14t baler, old hay rake and forked manure by hand - a lot of hard work. I have no regrets leaving that hard, manual farm work behind, but I do miss the smell of a plowed field, or fresh cut hay.

Ours are on a 10/12 pitch garage and south facing and they shed snow within a few hours - heavy snows they shed every 8-10". I also use a snow broom on the lower two rows to get it to shed faster. Amazon.com

Those views and privacy - looks like paradise! Awesome property Beowolf

This is the roofing co not wanting to guarantee aganst leaks which is understandable if the rack mounts are not installed correctly. However the total cost of the re-roofing and solar installation is allowable for the 30% tax credit - so if you spend 20K installing a new roof and 20K for solar...

Look at off grid systems - you will need about a 5-7 KW solar array and 14-20 KW backup battery system - probably better part of $35K unless you install yourself. You need to factor in the winter a 6-7KW array will generate 300KWH per month Dec/January in Michigan. Best case a grid tie array...

Your fortunate only 3 buckets on 5 acres - here they push up a new crop every winter so either fill and level soil around them or dig them out. What's that you are dragging - looks like a FEL bucket or is it a grading device with slots to catch rocks?

This unit is made in China 25HP 2.8 Ton Mini Excavator YANMAR Engine，Diesel For Sale| CFG-STE35SR - agrotkindustrial by Shantui who make very large dozers and excavators. Shantui also build this model for Kobelco and have other OEM relationships too. These are decent 3 ton machines with a...

To the OP why not keep the Mahindra and buy a smaller tractor for the wood lot work 25 HP with minimal electronics like the Kybota 2501 or get a lightly used 2012-13 pre emissions tractor, Having two is tter than one!

Don't use cable as bcp said, and with chain you will need a smaller 1/8" or maybe 3/16. Chain uses velocity to shred stuff vs cutting so takes more power to do the work, I'd stick with old blades and maybe try to raise the deck higher to clear rocks?

Yes - LD1 posted some very good and valid info on the mini ex size and capabiltiy vs a tractor BH. Really depends on your ground and what you are doing between the U17 to the TB216 - Both will work well and out dig the tractor BH. If you are doing this as a business get the bigger machine...

There are a number of threads on TBN on this topic, and as far as dealer cost buy it from the whole goods from Kubota - should be around $700 for the mechanical and you can add hydraulic...

Thats $7200 USD installed which is typically what they are here - also make sure if includes the subframe, For the same or less money you can get a mini excavator 1-1.2 ton - gas, or for $3K more a 2 ton with a kubota or yanmar diesel. You will get more done and better utility with a mini...

Had 6.5 acres 4 now, as we sold 2.5 acres 2 years ago to good friends to build a house. This was part of our retirement plan and wanted to pick our neighbors. It has worked out well.

Agreed - grandfather from 1900-1955 had 200 acres of woodlands and 100 tillable and did cord wood for the paper mills in the winter, and milked 30 Jerseys, bottled and delivered milk and eggs to 250-300 houses year-round. The side business was the wood business. My father took over the milk...

Oosik - didn't know you lived in a castle :-) Redirect Notice

You should be OK if you have pallet forks on the SSQA its 2400LBs at the bucket pins. TractorData.com Massey Ferguson 1759 tractor attachments information So it's close depending on the tote and pallet weight. Also have a good ballast on the rear!

Agree on the mulching approach - however from the pictures it looks like you could do a lot of the areas of brambles and smaller stuff with the BH leaving the trees and shrubs for the mulcher. Of course if you don't know what's out there (bigger stumps or rocks lurking in the underbrush)...

Yes the devll's in the details - my neighbor/friend is a builder did a 1.2M build last year and the architect did the same thing in BR and kitchen so this seems to happen a lot! Just frame it up and you will be fine - and I agree, a good window is worth the $ - Pella/Anderson etc. but dont...

Doc - that's a great deal on 2 Ton, Kubota diesel, Hyd cooler, dual pumps, pilot controls and thumb! Last week at auction, the Machpro 15 or 16 as it was listed with cab (2400LB machine) with Kubota engine went for $7300 plus fees, or $8300 OTD. Essentially its the same as the B&S version with...

Doc70 just curious what the offer was from Kamran - as I contacted them a while back and couldn't get them to reply. If they are selling for under $11K for the 4000LB unit with thumb delivered that would be a good deal.

Kamran and Typhon Terror XVII are the same machine- showing at 11,600 for the Typhon - I think machinery asia is the same as exavatorusa and are connected to Typhon it seems. Kamran seems more of an importer of automotive stuff. Yes the auction machines are going pretty cheap - but fees 10-15%...

Excellent news and kudos to your local dealer too. And the junk dealer really likes that part - he will likely have it to enjoy for a long time at that price!

I pick up the big ones 1" and up in early spring then thatch the yard with this the pick up the few piles with a 48: dethacher behind my cub cadet then vacuum with the trac vac During the mowing season I mulch them if they are small.

Agreed on replacing the back windows with standard units. Also, with Anderson, I found the big box stores will beat the lumber yards by a large margin especially if you get into the 400 series. Also have them quote the whole house exterior doors and windows for a better deal. Anderson are...

Yes - with enough time and effort a shovel or a 1 ton mini ex can do that :-) If you have the space maybe get a full sized TLB for 15K (JD 310, Case 580 etc.)

Level the dirt, put down some 2x4 PT sleepers with a piece of 4x8 plywood on the top and a few dollies from HD or lowes would work. Or build a dedicated platform to drop the BH and if alignment is an issue add a backup camera - they have gotten pretty inexpensive now.

Probably not a lot of demand for the part, you might want to buy two if he has both - maybe offer $150-200 for one and $300 for two? Shipping is going to be $$ and need a sturdy wood box or small pallet.

I did the similar process shown in the video two or three times - then I built a rolling dolly the BH sits on at the height above lower cradle. It's simple now - just roll the BH into position behind the tractor so the pins are above the cradle, hook up hydraulic lines, lift the BH, remove the...

Yes, typically the diesel 2 ton (3500LB) units have hyd filter and oil cooler, with pilot controls (vs mechanical). There aren't many here that have the 2 ton units, but Fredrik ordered one direct from China (for delivery early this year - but he hasn't posted results yet.