Search results

Also forgot to answer your last question. I’m in Eagle, Idaho. The tractor lives at our cabin in the small mountain town of Cascade Idaho an hour or so north of me.

Thanks for this. I’ll head up with a new battery and see what she does. And yeah the starter wasn’t to bad at all. I guess my philosophy on any parts has always been it’s not broke until I’ve taken it apart, inspected it, cleaned it, and put it back together again… I win some I and lose some...

Thanks… I did get a new 850cca ever start max group 65 from Walmart for it a few years back it seemed to work nice but maybe hasn’t lasted as long as I wanted it to. Has anyone been able to fit a bigger battery in it or found something with more CCA? Open to recommendations on what to buy and...

Thanks for this. I’ll look at those spots as well.

Thank you everyone! Sounds like I need to be more highly suspicious of that battery. I think I’ll plan on going up there with a fresh 850cca battery next time, also clean cable connections, check my ground, and test the starter directly with some jumpers to rule out the cables themselves being...

Howdy Peter, I connect the cables to the positive and negative terminal on the battery over the top of the cable clamps. I don’t believe the posts wiggle. If memory serves me correctly they are solid when I hook up to them but I will check next time I’m at the tractor. I can check out the...

Thanks I did try this although I will admit I didn’t get them as clean as I could (my wife brush wouldn’t fit in all the nooks of my cable ends) but I got em about 90% there. I’ll bring the right brushes up next time I’m at the property and get em good and clean. Thanks

Electric system schematic for reference Also of note I forgot to take pictures of it but the pin connectors out of the voltage regulator had appeared to get very hot at times and nearly fused one of the wires perhaps causing a short. I replaced the regulator with one I had laying around add...

Howdy gents, I’ve been having a problem with my ym276d starting up. When I turn the key it is very inconsistent on whether or not it fires the starter. If I hook it up to my battery charger and set it to “jump” mode then it will typically start just fine. I checked the battery first by taking...

That’s excellent… what might have been…Thanks for the story. For the record I’ll take my old yanmar over a JD any day ;-)

Super useful service bulletin. thanks for this. See reply below for the avaialbily of the kit per Yanmar in GA. Also I did check the lock nut on the one that came off... it was not lose. I really don't see a way in where they can loosen either its a pretty stout design as for as that nut goes...

Just a little Follow up on this. You all were so helpful I figured i'd close the loop. I got the new stub all put together and installed this last weekend up at the cabin and this time there were a few different findings. I did check the lock nut on the old one once i got it off... it id not...

Surely there has to be some hanging around in a scrap yard somewhere. Let the search begin. :) Odds sound slim to none but hey they will always be 0% unless I try!

Great find. Thank you!

All great info I will check into the lock nut when I get back to the cabin/tractor for a repair two weekends from now. So this HD kit does not fit the 276d correct? The first time I broke it I blamed myself for to heavy of a load and digging/pushing with 4wd on… so imagine a heavy pushing...

Thank you. I can’t find my better photos of the wheel broken off last time but here are a few of it from some photos I had when my wife was working on it.

Would you please specify? I guess I don’t understand. Turning radius? Corner of the broken part? I’m not sure what you are asking.

Thank you. That might be it… should I just order a new relay and replace it then go from there?

There is nothing touching where it snaps off except an the axel seal wear color which I have pressed on at a local machine shop before I do the install.

Sorry forgot to reply to you and instead answered your questions in the thread below.

The tire sizes are stock and correct. I drive with 4wd mostly on idaho dirt in the summer mix between packed and loose then ice/snow in the winter. I hardly ever use the diff loc. it is the pedal under my right side of the seat that I can engage with my heel correct? Honestly I never knew that...

Snaps right where the center meets the hub, See photo of axle. There are snap rings involved but if I remember right from my last install the top silver piece in the photo threads on last to hold everything together. Here is a parts diagram photo as well and link to hoye to determine what is...

From what I can tell they appear to be installed properly. Or at least when repairing the stubs the parts are all in line with the diagrams I have found on hoye. What would I look for if a prior owner had modified it?

FYI it is a 4 wheel drive capable tractor and it does usually snap when I have the 4wd engaged. I have noticed when my 4wd is on not all 4 tires are spinning. Is that normal as well.

Hi gents, I’m having issues breaking my front left stub axle. I am on my third one in 1.5 years. It’s getting old dropping 350 on a repair every time. Admittedly it is when I have a load in the bucket but after the first one I have began to be more careful and it keeps happening. Yesterday it...

Just following up on this with you both as you seem to know these rigs well… I replaced the ignition switch a while back and it did not fix it. The lights remain on when the tractor is off and key is out. My solution was to unplug the dash panel completely but o sure would like to have my lights...

Thanks for the info and cool old documents. Yeah I have the a later model with the YFL 1075. We love that tractor. I’ll go check out hoye for the ignition switch. Thanks again!

Hey all I have a yanmar 276D that when I turn the key to the off position and remove it the panel lights stay on. The only way I can get them off is to remove the battery cables. Curiously it shut off the last time I powered down but when I went back out an hour later I saw the lights back on...

Thanks guys. Both useful and good information. Onward!

Great thanks... I’ll post there!

Or better yet has anyone specifically bought one or delt with an aftermarket company that could help me find the replacement?

I am looking for info regarding an old yanmar YFL loader YFL 1075. Particularly the front left tilt cylinder specs to see if I can find a replacement for it. Center to center pin length, bore, min/max stroke etc. any information you have would be helpful thanks. I have dropped off the old one at...

I am looking for info regarding an old yanmar YFL loader YFL 1075. Particularly the front left tilt cylinder specs to see if I can find a replacement for it. Center to center pin length, bore, min/max stroke etc. any information you have would be helpful thanks. I have dropped off the old one at...

Hello all. I recently got a great deal (to good to pass) on a 6 ft priefert rmx600 it痴 a 6 ft rotary deck. However the thing is giant, a lot bigger that I though it would be. I have a yanmar 276d with a 27 hp engine and 23 hp to the pto. The recommended hp for the deck is 40+ no more than 60...

Hello everyone... I'm the proud new owner of a Yanmar YM276D. I can't wait to tinker with it and make it mine. For starters it has a flat tire on the rear, when I tried to put air in it the valve stem broke off due to dry rot. The other side looks just the same. So I plan on taking the rear...