Search results

I used LED "ufo" style high bay lights in my shop with 16.5' ceiling height. Work great, used 8 for a 40x40 area but could have used 9 (the garage door made the 9th light pointless). They have fantastic coverage. With what you're talking about you could probably get by with less fixtures...

Picked up this Delta belt/disc sander earlier this week, not sure on age, but must have been one of the last of the industrial/USA made versions based on the stickers. Other then some damage to the outer belt guard from a mis-tracking belt, it's in great condition.

I recently purchased a Nissan forklift, was able to get a good deal due to hyd. fluid entering the crankcase. I pulled the pump off and sure enough the front shaft seal lip was partly flipped over, I am going to pull the pump appart to inspect to see if the overpressure at the front shaft is due...

Very nice, did you adapt that loader from another unit? I have a 1920 that's been getting a diesel swap although it's been on hold for about 5years. Did you do anything to the front axle's besides the hubs? They are definitely a weak spot when you start adding the loader. I did the same hub...

Shoot, that things not even broken in! Wish mine came with that pile of filters though.

Picked up the compressors today, awkward load due to how top heavy they are. Luckily they were just PM'd and the belt drive had the belts replaced right before being taken out of service. They have high hrs but believe they were run in continuous mode so probably not a lot of loaded hrs. Build...

Well I was planning on using this pair of I-R 5hp T-30's. Then I was given this almost new 7.5hp I-R, which I planned on using with one of the 5hp T30's. Now I have the opportunity to pick up a 20hp Quincy screw for a heck of a deal, so thinking I'm gonna keep one of the I-R for a backup and...

And I have this in case I need to do a lot of "dirty" welding [emoji16]

Was able to get the stairs in place the other day, still need to cut some spacers and level/anchor everything. Kinda wishing I had pressure washed and painted them before getting them in now.

With the exterior pretty much done and my final signed off on I was ready to do a little on the interior. I cant afford to finish the inside yet but already had most of the materials to build my storage mezzanine (here you go BB lol). I went with a 10ft off the back wall and full width of the...

Next up was the trim and siding, went with PVC for all the trim boards and vinyl for the siding. Luckily I bought a set of used alum-a-pole and jacks to complement the old 2x4 built poles/jacks, they came with a selection of walkboards so I was able to handle the 50ft long sides. I put...

Gets me a little out of order as I slacked off on doing the floors, but the concrete company gave me some filler and 10gal of Super Diamond Clear because of some of the issues with the floor. I wouldn't recommend this for a shop as I found out the hard way it doesn't have a great chemical...

With the minimum wiring done, I was able to get my permits signed off on (after a few minor changes......) which means.......power! For lighting I decided to go with 8-150w LED "UFO" style high ceilings lights, I placed them in a even spaced grid in the first 40ft of the shop, the back 10ft...

I wouldn't say I "enjoy" it lol, but i do get a lot of satisfaction from making the bends/conduit looking clean. I think if I ever go into a building trade it will be plumbing or electrical, I've re-plumbed 3 houses and actually enjoyed it. Amazing to see what other "professionals" have done...

Lot more conduit run, all the electrical boxes installed. I decided to go with 50A twist locks for all the 208v stuff, used a small piece of SOOW to connect them to the boxes, figured I less of a chance of breaking off a connector that way. Lucked out and found a bunch of like new 3ph takeoff...

Electric being run, I lucked out and found a nice 42space 400A panel full of breakers for a great deal, it was an installed but never used deal. I wasnt able to use all the breakers but it still saved me a lot of money. In order to run the service wire to the panel I decided the only clean way...

Picked up this little Columbian 73 1/2 vise from an auction the other day. I need to make a post mount and the locking piece for it, but otherwise it's in decent shape.

Next up was setting the pre-cast pad for the transformer to set on, after some discussion with the power co. design engineer, we decided to set the transformer close to the shop for minimal voltage drop since I am about 250ft from the pole. It ended up being a little closer to the shop then I...

With the roof on, doors in, and tyvek up it was time to get to work on the electric. I was very lucky that a few years ago the power company ran 3ph right in front of my property as a back feed line to the lumber mill down the street allowing me to get 3ph at my shop. I decided to go with a...

Doors all in and working, you can kind of see the trim in the pictures, still working on the tyvek, man that stuff isnt fun to work with if theres any wind! Also a pic of the floor after grinding, the cold joint area left a rough spot that extended in a stepped line that extended across the...

I didn't really get any pics of the roof other then this one of the underlayment. I went with a dark dimensional shingle that matched the house. I was pretty busy trying to get the roof on before we had bad weather, as you can see in the background I did get snowed on once or twice. The...

Framing want pretty well, had a good crew that got it done in about a week. Walls are 2x6 Framing done and sheathing on, now it was my turn to get back to work on it.

Here I'll help with that, saw this going down the road the other day. At least they tried to strap.

The brown and black is Shelby, raised her from a 6 week old pup, she use to ride with me when I had my transport company. The all black is Bruno, he's a SPCA rescue. Unfortunately last April I had to put down Shelby due to her health, still haven't gotten over losing her, Bruno is still a...

Drain tile and gutter drains installed and back filled

I watched them pull it up, they were waiting on the truck that was late in those pictures so just standing around. It's hard to tell in the pics but it appeared to be in the bottom 1/3rd of the slab. I've seen worse flatwork but was a bit disappointed in it, granted we also had less then ideal...

Flat work crew getting the base, plastic, and rebar in. They worked so late I couldn't get a good picture before they started pouring in the morning. Because if the lack of access along the sides of the building we ended up getting a pumper. Slab is getting poured, unfortunately the weather...

Footers done, didn't get a good picture of them working, actually didnt get nearly enough pictures of some aspects of the build. As a plus, the concrete company forgot their 16in bucket at another job so I ended up with 18in footers instead. I hired out the concrete work and framing, goal was I...

Since I live out in the middle of the woods I had a lot of trees to take down, unfortunately most were either poplar, beech, or pine which I don't burn. Did get one nice white oak and hickory out of it though. Worksite is finally coming together, luckily it stayed dry pretty much the whole...

Well I've been putting off posting my build but Big Barn finally convinced me! Just as a precursor, the shop has already been built but suggestions are always welcome so hopefully others can benefit. A couple years ago I got the go ahead to finally build my shop, I've been working out of the...

My dad has a 4.5x8ft SnowBear he bought at Costco a long time ago, out of all our trailers it's probably the most used. We actually had to remount the fenders higher because the tires would run the fenders from being overloaded I guess. My plan is to build a 5x8 copied off it. Here's a picture...

I have had my W5021 for over 22 years, bought it used so not sure how old it actually is. Was kind of excited to see Kubota bringing back the trim mowers and apparently doing it right. I'll have to say I haven't seen the new one in person but looking at the brochure it appears to even have...

Yup, or search for "spring bushing", that's what I used in a lot of my main pivots. For my pins I made them the "grease through" type but you can have a grease fitting on the sleeve if you have access to put one.

I'm the same way BB, buy cheap, however that means doing a lot of rebuilding also. My first lathe was a earlier, 1947 I believe, South Bend 13" (had the single top lever on the gearbox), rebuilt the carriage and a few other parts on it. Sold the SB to buy a 13" Clausing Colchester, rebuilt the...

You could make one similar to the water table on my cnc table but with an open bottom. Use angle to make make a frame so the slats have something to rest on then use some 1x1 angle cut to the desired spacing to hold the slats in place. You can kinda see how the angle is setup in this pic.

Looks like we have similar setups, except someone painted yours the wrong color.......

Grabbed a couple pics of my hossfeld in storage, the dies are all just thrown on a pallet under my break right now, have to inventory but I should have a full set of a angle iron dies both inside and outside bends, plus a few pipe dies and all the normal pins/pieces. It has the older hyd. pump...

Mine is just one big room, except where I'm putting the mezzanine and will probably enclose part of it to separate the machine shop area. Here's a pic from while I was working on the mezzanine, i still haven't moved into the shop yet so it's not organized at all. The plasma table is going to...

I like that magnetic chuck deal, I was able to get a Dake 1 1/2B awhile back, also have a Greenerd 3JR arbor press with stand that needs some reapirs. The Greenerd came from an old DeWalt repair facility and came with a bunch of interesting adaptors. Here's a pic of the Greenerd, it's still...

Looks like a brake shoe riveter to me also. I have a slightly newer 75t Dake, they are pretty awesome, only reason I have one was because it was free.........

That's a nice setup, I've been looking for a smaller overseeder I could afford for awhile now. Finally picked up this Olathe 4ft verticutter with seedbox about a month ago. Did a few test areas this spring, hopefully I'll have it cleaned up and ready for the fall seeding.

I lied, found a couple pics. The 1/4" flat stock was heated and formed more to the cylinder after it was bent, the pin is a piece of 1144 pressed and welded on the backside into a piece of DOM tube.

Agree, I was able to balance mine between depth and height but if I was to build another one I would favor height a but more. Mines a bit smaller then the one you built BFreaky, one of these days I really should paint it.

Re: Do any Kubota BX23S Owners have this? I found l pictures online of other BX23s' and they looks the same as yours, definitely looks odd but not uncommon. I have a few spots on my B where parts were mounted during assembly/painting and there isn't paint on those areas.

I'd try to go smaller, I have a similar size bucket with a tooth that appears to be smaller then yours and its too big for me.

Crack goes from edge to edge so nothing to drill, it will get beveled. Going back and forth on brazing or using nickel rod. Based on my buddy that does this type of work all the time I'm leaning towards using ni55 rod, plus he already has some I can use :) Got it appart, now it's time to clean...

Picked up a large drill press the other day, wasnt really looking for another one but this one showed up on Craigslist cheap and nearby so I figured it was worth looking at. The ad had a couple pictures but not much info, could it really tell what make/model but it looked to be a decent size...

You didn't say the footprint of the blocks on the trailer but I see no problem unless theres a high point load. Are you going to have dunnage under the block? If so use 4x4 or larger and make sure the load is spread over multiple crossmembers. I know this has a large footprint and a steel...

And there always good old persuasion. I had to straighten this 3x3 .120 wall tubing. It had pulled almost 1/8" and needed to be 1/32nd or less, a little creativity and it was back to spot on. I asked a very talented fabricator friend, that I've seen use the heat and cool method to straighten...

Picked up this Wilton 1765 vise off CL today, the movable jaw is frozen but seems to have little use. Figured for $75 I couldn't go wrong. Hopefully a good soaking and it'll free up.

I'm using the precision plasma llc Magnum HD7 gantry and plans. I could have done my own but because of time constraints this was the most economical way to get up and running quickly. I'll be using the water table for now but might switch to a down draft setup later on. The guy wasn't...

Pocked it up today, my machine torch wont be here for a couple weeks so I'm going to borrow a buddies hand torch to test it out, I did plug it in and it powers up and it switches through all its functions. I have a trailer of steel waiting and hope to start on the table this week. Other...

So I'm getting ready to build a cnc plasma table, the original idea was to pick up a mechanical torch for my Hypertherm 45 and use that until I can upgrade. While poking around CL I found an excellent deal on a Hypertherm PM105 and should be picking it up tomorrow. Looking around I see very few...

My 16ft deckover dump is lighter, but that's due to having an aluminum body.

Yeah unless you do a lot of heavy blasting that's probably overkill, at least the screw's have a lower in rush for startup compared to the piston type. Guess while were talking compressors I can post my 2 older t30's for my shop. Best I can tell they were all USA made.

It's just a double pilot operated lock valve that goes between the cylinder and directional valve, it stays in the closed position until a certain pressure is applied to one of the ports on the valve (usually a couple hundred psi, that is the pilot pressure) which allows the valve to open and...

Same here 5/4 deck boards, except I have mine 4 high, works great and I can take the 15ft section off by myself, but it is heavy.

No pto on mine unfortunately

I like it! I've been keeping an eye out for a model A trans. to add an aux. to mine. Curious about the distributor conversion, does yours the IXB engine? What do you mean by gear starter conversion? Here's mine in all its rusty glory.

Figure I'll throw a few pics of my bigger US machine tools Ive acquired over the past few years in the thread. Walker Turner 16in vertical bandsaw (auction find) Wells Index 847 mill (ebay) Clausing 2277 drill press (auction) Kindt Collins Master 24in disc sander with table extensions...

This is how I did my remotes and TNT on my B2620(basically the same tractortractor), I'm still trying to get around to adding other 2 remotes on the left side of the rops. The top link is from surplus center and I made the side link from a generic cylinder from surplus center. I added a...

I have the double high, bought them to work on the new shop, they have a bit of movement around full height but nothing bad and I quickly got used to it. I opted to buy them instead of a large A frame ladder and glad I did, much quicker to run wire with a second person to move you around or...

Found a picture of my tilt cylinder.

I'm still working on building mine, 40x50x16.5, single 18x14 door with 2 man doors and 2 windows. I wish I had put in more windows (still might), I roughed on for adding a bathroom later. Doing it again I would have looked into a red metal building more seriously. I needed the building to...

Going to look at a early '80s Case Davis 30+4 tomorrow, does anyone know what it weighs? It has a 48in depth trenching chain, backhoe/blade, and the boring pto. Trying to figure out if I have to borrow a heavier trailer as my 10t is out of commission at the moment. Can't find anything on this...

With mine I usually have 6-700lbs of weight on the aerator and it still struggles unless the ground has just the right amount of moisture. Found some pictures of mine on the phone. ATTACH]543689[/ATTACH] Where abouts in va are you?[

If you knew what I paid for it you would probably say I suck! Got it off a gov. auction site and was suprised nobody bid on it. Little bit of a drive to get it but not bad. This is my latest auction find, paid more then I like but still cheap compared to most, this was a longer drive too...

I was planning on building something similar with an inline duct fan, ended up lucking out and picking up a Torit for less then materials cost, downside is filters are a bit pricy but I don't plan on changing them often.

If I didn't want it spec'd the way I do mi could probably have picked one up today. I'm not worried about the wait, gives me time to get my other trailers ready to sell. They were actually better then the next further dealer, their wait time was end of June beginning of July. The 10t almost got...

Got that right, I did a 18wx14h on my shop, never know when you might need to bring in a dump truck or rv. I also only have 1 door so had to make it count.

I just chuck my annular cutters into the drill chuck on my mag :) But it's not very fun to move that drill around, weighs about 90lbs.

I also managed to snag a few Patterson air cannon fans from a warehouse that was changing out equipment, should keep the shop tolerable this summer until I can insulate and put in A/C

Just picked this up from a surplus auction, wasn't looking but always wanted one and the price was right. Need to clean it up and replace a few foam seals that's are deteriorating and get a new filter. Now just need the new shop finished so I can use it, been a few months since I picked up a...

My B2620 helping clear the land for my new workshop, mostly hauling off the trees and brush I knocked down, also took care of a lot of the finish grading.

I picked up this Clausing 2276 last year from a surplus auction, needs a little cleaning but appears to have little use and was still cheaper then the 20in HF press plus it's a lot more machine. I have 2 mills, a turret and a bed mill, I thought when I bought the first mill 5 years ago I...

There's no way I could mulch with the amount of leaves we get, just finished my customers larger property and if I hadn't collected it probably would have raised the ground level an inch. We also have acidic soil and with a lot of oaks it ends up being bad for the grass and requires more lime...

Well I finally got around to ordering some tires for the dump trailer, ended up going with Gladiators, should be here next week. Price was good and they seem to have good reviews, can't wait to change out the Maypops that are on it now. I like the tread pattern too.

My big trailer has double hinged ramps so they don't get hung up on uneven ground. I've had the style with the fixed support on the ramp get stuck once loaded. And yes I know I need to replace the deck.

I have a B2620 (predecessor to the B2601) and do similar to what you described in your post. I have a 50in root grapple that stays on most of the time and use it to clear/clean up a few properties and do selective clearing in the woods (one customer calls it German forestry). I keep thinking I...

I need to replace the tires on the dump trailer, was going to convert to 8lug hubs with 16in wheels etc. but after doing some measuring and figuring decided to stay with 8-14.5 tires, found a good deal on some new Kenda Load Stars. I've used their more standard trailer tires in the past and...

You'll need articulation for the rigid mount unless your land is completely flat. When I built my vac I didn't provide enough torsional movement in the mount and it caused all kinds of traction problems, 4th season I made a new mount that allowed for easy vertical and torsional movement and...

When did they standardize? I've never found it difficult to select between the 3 sizes in the U.S. My Land Rover have a proprietary adaptor to provide a 2in receiver, it's an LR3 and has a higher towing capacity as my dad's F150 so seems to be pretty stout. I don't mind the look a a receiver...

Most has been covered but I'll add that getting a 3ph press can sometimes be more affordable, adding a variable frequency drive (VFD) will allow you to run on single phase and adjust the motor speed up or down some if needed. Here's my drill press and mill

They are really good for cleaning out the ditch under the mailbox too!

Not really wrong but sure kept most people away from me!

Figured I'd update the thread, picked up the trailer last Saturday, have to do a little work in it which I suspect. Need to replace the decking and I plan on rewiring, structurally it is sound. Also I'm changing out the pintel for a ball coupler, it pulled well on the way home and doesn't feel...

Well I'm finally going to check the trailer out in the morning, looks like I can get it for 2200. It's more trailer then I need but at least I'll never have to worry about overloading. Looks to be in decent shape from the picture.

I'm possibly going to look at an older 10ton deckover tag trailer. Mid 80's, dually tandem 10k axles, 19+5 dovetail deck. I've looked them up and the new ones look pretty nice but not sure how the specs compare to the older one. I know it needs some new decking boards but is supposed to be in...

The case is aluminum, if you have the ability to weld it it would be a worthwhile repair. I found a picture of the trans case I repaired awhile back, it was tough access and kept finding more cracks to drill and weld as I went. This was on a trash truck that had the hydraulic pump pto u-joint...

Turned out nice though, I can't take any credit for that, only charged with moving it.

And to get back on topic, This was one of my more interesting projects, over width and borderline on load capacity plus a lot of tongue weight, it was only for a few miles to get it to the shop to paint it. The wing had a better safety margin, was still worries about it catching too much air...

Picture didn't attach. Couldn't find a good pic of the fronts on my phone.

Re: 1st dump trailer as tractor hauler... Lo Profile vs standard? PJ, Loadtrail, H & Do you have Bwise in your area? They make a very nice 16ft dump. Just to let you know it's very easy to overload a dump so be careful with an f150, the 16ft are a bit heavier to begin with also. As for...

Here's some newer pics that show the wheels better.

I like what they did with the xp, I have the earlier PM45 and love it, built many a projects and even made quite a bit of money with it. I think my next one will be a little bigger unit but but if I was in the market again I would be buying the XP. You'll be amazed how quick your projects move...

First you need to remove the metal power beyond line that comes off the loader valve and and provides fluid to the 3pt. The red circle is the loader valve side banjo fitting. The 3pt side of the line is circles in red in the following pic, note it'll be a gray steel line, not the flex line...

I run turf on my Kubota B2620, looks to be the same size as your tractor. I actually had r4 and switched over about a year ago for doing turf work, like them soo much I don't see switching back. Fronts were up sized from 23-8.5 12 to 23-9.5 12, mainly because I already had a brand new tire in...

Looks like it works good, about the best use for those tracks I've seen! I have to leave my wood outside until I build a woodshed, I have a lot of 2x4 3/16 rectangle tube left over from temp framework for a plane so I made brackets to hold 2x4s It's 10ft wude x 5ft high and holds 2 rows of...

I'm hopefully going to be starting on a workshop once the weather breaks in the spring, until then I'm working out details like electrical, I'm friends with electricians but one doesn't have a lot of experience in commercial applications and the others mother just passed so it's not a great time...

I have a 16ft deckover, I plan on building ramps for when I need to haul my tractor but it's not my first choice for moving my equipment, I use a 18ft low profile and one day hope to upgrade that with a 20-22ft rollback deckover.

Re: Converting 3 pt woods 6000 backhoe to subframe mount Looking good, when I built mine I kinda copied kubota and made the subframe stay with the tractor and the bh a 4pt quick attach. Tractor side. Backhoe side It ties into the loader frame, ROPS mount, and rear axle. 2pins and 2...

Thanks, when first built it I didn't have a very well equipped shop. It was built with a chop saw, angle grinder and small 120v welder. I was able to use my buddies shop to roll and brake the alum for the sides. Needless to say I've aquired a bit more equipment over the years which has allowed...

The new assembly mounted on the vac, the old assembly is to the right for comparison. I also had to make a new mower deck adaptor, was running out of time for the season so just threw it together, second picture is after the mods this year. It really fills the hopper nice

I kept the impeller simple also, just a 4 straight blade, easier to layout and balance. The new engine is a B&S 10hp I got used off CL. Hose size is now 8in. Here's the impeller parts cut out. Everything machined and ready for assembly, I milled slots in the backing plate for easier...

It wouldn't let me load another picture so it'll have to be multiple post. Here's the start of the blower housing, after a lot of drawing it out and mockup. I didn't go crazy on the design, mainly scaled up and improved a few things of the design of the old housing. Housing almost done...

I built this vac 6years ago, the original build was documented on another site, it served well doing multiple yard cleanups over the years and received a few repairs and upgrades over time. The blower I used when I built it came from an old Ez-Vac I aquired, it worked well but was worn out...

I used casters on the vac I built 6yrs ago The hose still has to flex but not as much and can be a lot shorter.

07 Ram with the 6.7L deleted, 6spd auto. Need to upgrade the trailer soon but it's served me well, started life as an open center car trailer. The dump trailer still needs some more work to be where I want it. And if anyone can flip my pictures over I'd appreciate it.

Here's the delay style, as you can tell it just activates the shutdown lever on the injector pump.

Here's pictures of the newer type without the timer. I don't believe you can open them up. And a ref on location

My little Mazda didn't have a hitch........... actually worked rather well.

Or he's like me and wanted to do somthing like launch a jet ski and had to use what he had in the truck..........

Re: Rear Remote Valve Controllers: Let's see some pics! Sure did, the gaurd is partly because my arm rest on it if I turn around, that valve gets pretty toasty after some heavy loader or backhoe use. Sorry the pictures are turned upside down. Here's one of just the mount. I'll have to get a...

Re: Rear Remote Valve Controllers: Let's see some pics! Here's mine on the B2620, I'm getting ready to add another 2 spool valve on the other side of the ROPS

Bought a Gannon FD100 off CL the other day, it's a stout piece, might be a bit much for my Kubota but we'll see how it does soon. I didn't feel like taking the BH off to test it yet, I'm not going to sell my standard box blade just yet in case it too much for my equipment.

They are nice, I did a lot of research when I was building my BH and decided to go with them. Here's some of the over 20 pins I had to make, a lot of them have grease passages, took a little while to make!

Since planes were brought up, thought I'd add this

I made a line boring setup a couple years ago, pretty simple and works well. I used spring bushings when I made my backhoe, pins were made out of 1144 stressproof. Mcmastercarr has a decent selection of spring bushings. My drive system, fixed at between .005-6in per rev.

Looking for info on their kits, pricing seems decent, but haven't been able to find much in the way of reviews good or bad. Anyone have any firsthand experience with them? I've been wanting to add a shop at the house for a while and have been gathering info and trying to price out differnt...

Sounds like you got a good deal for all those attachments. Making a subframe for the BH isn't hard, if you search this site it's been discussed in length so there should be plenty of info and pictures to look through. When I built my BH I copied Kubota's mounting for the factory hoe, my...

What about powering the bh off the tractor? Looking at the factory mounts there should be room to run a pump off the pto, would probably just have to push the BH out a little for clearance. I made my own BH on my B2620, it uses a subframe similar to the factory one. I run mine off the tractor...

Just put one on mine this year, pulled it off a Jacobson fairway mower I picked up, was even a close enough match for Kubota orange.

Putting in a new 40ft culvert, was tough digging where the old road used to be.

Looking at a L4740hst ROPS, it was a rental where BIL works, 932hrs, Loader, quick attach with a heavy duty long bottom skid steer bucket, R4 tires in good condition and a 6ft Land Pride rotary cutter in good condition. Tractor looks like it's in good condition other then the paint looking a...

Guess the safety police will really like me, son is 2 in the pic. Still have a few things to finish before I paint the hoe, hyd. thumb is on that list.

I'll add some of my little homemade bh digging out an old oil tank. This is one of the first larger projects I did with it.

And the 3pt fitting

Found a picture of the loader valve I used a sae8 to jic6 90* to connect the hose

Hello everyone, looking for some input on replacment tines for a tiller, I've done some research on it and still haven't made up my mind so figured I would get experienced advise. I bought a used JD 660 (built by Howard) a couple months ago and it could use some new tines, the PO replaced a...

I made this a few years ago for my plasma with what I had in the shop, needed it to make the disk for an aerator I was building. Still working good, even made the wheels for it.

Sorry they are upside down, have to work off my phone right now. It bolts in using existing holes and doesn't require the removal of the bumper. For the license plate holder I just made a simple plate that pinned into the receiver when not in use. The guy I built this for uses it to mount a...