Search results

I cut the end off the arm and welded an extension on it with a slot in it. I made the arm into a box with some 1/4 diamond plate I had.

Don't know if this will help anyone, but I found a couple of pictures from 25 years ago. To hold the pipe up while unscrewing each piece we used a 1/2" plate like the piece of paper in the third picture. Just slip it over the pipe and the coupling stops the pipe from falling while you unscrew...

I've always wondered why we can't pull trailers like the second one in the picture with our cars and pickups. They seem to work fine behind big rigs. Anybody know why?

I saved these pictures from a video I recorded off an ABC news satellite TV feed. Feel free to post your own if you have them.

Here's a 5 ton wrecker. The B&W picks have held up better than the color.

Here's mine. OK I had to share it. Almost 50 years ago, I can't believe it.

Very impressive tractor. I ran a AC HD10 crawler with a 4-71 in it in the summer of 1963. I don't know if your Dad has gotten any replies from Australia, but I've built 2 tractors, the large one also in 1979. It's not as large as your Dad's but it's done a lot of work. It has a Chevy 230...

I used 2" pipe with a reducer on each end. The desiccant beads turn red when they're used up so I installed a sight glass in the side so I know if they need replacing. I installed a 3 way valve so the tank can vent when being filled.

I ran across this article today. Haven't they cleaned up their diesels like we have? Or maybe they're all VWs cheating on the emissions. Back to gasoline I guess. Amid smoggy days in London, growing calls to clean up Europe’s toxic air - The Washington Post

I have the same valve on my tractor. On mine that bottom port is hooked to the tank. The power beyond port is on the other end. Yours may not have one, I've seen them without. I think you've found the problem, the power steering is doing something to deadhead the flow and the high pressure is...

I made this one for the sleeve hitch on my garden tractor. It lays wire a foot deep if it doesn't hit rocks too big. I used a 3/4" 90 deg electrical conduit bend and a pipe nipple. I added the plastic pipe reducer on top to act as a funnel. There's an arm to hold a wire reel. I buried 300' of...

Here's my 35 ton. I made it so I can bolt in small die sets and use it as a punch press.

Well I was bored, so I went out and measured the current on the capacitor leg. It's 22 amps no load, 20 amps full load. So obviously it's doing something. At no load the 240v draw is 11 amps. I used to be an electronics technician so you don't need to talk about guys pushing on a car. If I cared...

This is an old county grader blade I heated and bent. I didn't quench it. I used to use the left corner to gouge crushed rock out of a road cut, so it's kind of beat up, but it's been on there for 35 years. A file just slides on it where it wasn't heated. I welded it with stainless rod.

Just for fun, here's the 2000 ton crane at the third power house at Grand Coulee dam.

Here's a picture of me boring out a motorcycle engine cover for a different size water pump seal. It's bolted to a makeshift angle plate, and the boring bar is in the chuck. The engine is in my garden tractor, so maybe it's ok to post it on a tractor forum.

That should be a fun project. Is that a hydrostatic drive pump on your engine? Your plan to use 2 hyd motors will certainly work. Depends a lot on what speed range you want for your tractor. If you size the motors to have enough torque to spin the wheels.then your top speed may be slower than...

I routinely plow a foot deep with my 18" single bottom plow. Just did my garden a couple weeks ago. It will go deeper if I remove the coulter, or if I could raise it higher.

Some of the rods I use are difficult to restart after the tip cools off. 7024 and 6011 cause me problems usually. I got to thinking, why not just heat the tip up again? I have a propane torch that goes on and off by pulling the trigger so it was easy to try. It seems to work like a champ. No...

I just lifted my metal chimney up on the house in this picture about 25 years ago. I also used the boom with a hydraulic winch to pull 400' of 2" pipe out of the well to service the pump. I have several 8' sections of tubing to adjust the length. This is my first attempt at posting a picture...