Search results

arto, That is a good idea. I might bypass our local dealer and go to Subaru USA direct.... This is our 3rd Outback....

quite a range of thoughts. I believe it's the 2.5 l The dealer said we would get a 10 year/100k mi "curtesy warrantee extension" for anything related to the oil pump. But nothing in writing... They already pulled the oil pan so I don't have the oil for testing.

Hi folks, We bought our first new car in 40 years. At 9000 miles, check engine lights came on while on the road. Lucky for us there was a Subaru dealer nearby. They couldn't look at it until the next day. After 2-1/2 hours, they said it was all fine now. Drove 200 miles back home. The next...

Beowulf, I have mixed a lot of concrete in my bucket. The trick is to use as close the the exact amount of water needed. Measure the water! Mixing dry mixture is hard work I use a hoe and a shovel

My investments are needed for future living expenses, for the next 30 years. But if safe bonds have a return of 4% and double in 18 years, vs. S&P with average 10% returns and 7.2 years to double, you are leaving a lot on the table. The crash in 2000 did take a long time to recover......

one thing I never understood was the idea as we get older we should be conservative in our investments. Or have 1 year living expenses in cash. This is to prepare for a future down turn. I'm 65 and we are 95%+ aggressive. With S&P based funds doubling in value every 7.2 years, all the extra...

I'm in Southern Indiana. We have a patio system and one that runs in our garden. I have never done anything to the system in the winter other that disconnect the house supplied water. The one in our garden is 1/2 inch pex

I stuck a 4 inch pvc drain pipe in the ground like a post. packed with potting soil and poked green beans in each hole. I left room at the top to hold some water to seep down. We had a big garden so it was just for fun.

I was going to put it on my KAMA 454, 45 Hp tractor.

I bought old old Ford 758 backhoe many years ago to rebuild. It's a small one and was on and 8N. I never got around to it. The hydraulic lines are shot and the pins are real sloppy. The control valves were also shot and gone now. The cylinders would need some work or replaced. anyone want it at...

Scootr, I'm an hobbyist stone carver. I buy diamond tools on Amazon and they are cheep but do a great job. I use diamond core drilling bits for clean bulk removal. I use water on an old drill press. Likely, not best for every day construction, I will never ware one out drilling in marble and...

I bought a set a few years back. They didn't stop the deer or raccoons. I'm guessing just not a big enough zap

We have a whole house dehumidifier. AprilAir 96 pint tied in the HVAC system. It lasted 12 years and had a leak in the coolant. Replaced myself. By keeping the house dry, the AC can be set at 75 deg and feel great.

neighbors can be a pain. We have just one house close by. Previous owner like to communicate via a lawyer. They sold and new neighbor is great. It started with a tree down on her property and I mentioned I would cut it up and push it in the woods for her. It was a small job with my tractor...

1 old man, with all that rain, it will be a great crawfish season next year. It was dry last year and crawfish were expensive and hard to find.

Hawkinshollow, Yes we dry out the big ones and plant those seeds the next year. Once dry they will sound like a child's rattle. Seeds look like pepper corns, big and black.

not sure how big a Norway rat is. I upgrade rat traps with a row of finish nails nailed in from below the wire swing arm. They can't get out with 3 -5 nails going through their lower jowl

thanks Steve. Close to what I was thinking as well

My brother-in-law is no longer able to cut grass. He has offered it to us at no cost but we want to pay him it's value. They could use the money What I have found it was made 2011 to 2012 and has only 47 hours on it, garage kept. It starts and looks show room condition. What do you folks say...

To prevent slime, grill hot for a very short time. But sliced and cooked a long time would likely dry it out. We prefer barely cooked

Ponytug, we found out they are true to seed. When you miss the big ones the pods can be dried out.

A few years back we had a neighbor offer us a bowl of fresh picked okra. Here in Indiana, we know okra as the fried version and so-so at best. he said just cut them up sizzle it up in a pan. It was ok but a bit slimy. next batch we left them whole tossed in some olive oil salt and pepper. then...

1 old man, Here is a photo of my setup. The chicken wire is hard to see because I started with 2 x 4 inch welded wire 16 inches tall. But look at the post and you can see the chicken wire. Note the red fiberglass bar in the center of the photo. That is my home made wire spacers. It keeps the...

we planted 3 peach trees 2 ft tall. immediately the deer were eating the branches. Then came the 6ft dia wire round loop fence. Trees out grew loop fence. Installed e-fence around the garden and peach trees and the deer moved out and the raccoons moved in. I got serious. Installed chicken wire...

I just try to bug them more than they bug me. I'll dump a little old gas down their holes, another day run the garden hose down the holes for 5 min. Other days I'll just take a leak down there hole. I have poured cyanine pepper down the hole and fired up the leaf blower. Rat traps work great if...

Grown in my back yard! I'm picking peaches right now.

dstig, Ask your plumber why it was set so low? If I did it, I would fix it! That is raise it up

we had flying squirrels in our attic, then the black snakes moved in. We learned rodents will reproduce much faster than snakes can keep them under control. Those squirrels kicked insulation over all the soffit vents and black mold covered the entire underside of the roof deck. Set live traps...

Eddie, My wife did the same a few years ago. Same story, i thought it would be junk. Works great for our deck, now 4 years old

Our garage has a 16 ft and a 10 ft wide doors. truck is parked in the 16 ft bay! It's not just how wide doors are, you also have "stuff". Our layout is end wall/5 foot space/10 ft door/ 3 ft space/16 ft door/3 ft space/end wall. All 24 ft deep It is attached to house at the kitchen door for...

Nice, is that a 410?

the 5/16 bolt will go into the threads of an 8mm course threaded hole

I bought a 400 lb/120 gal propane tank, best price and free delivery. That way more than covered Prime cost

My father died young in 1965, he had accumulated 100 ac of his own but worked with my grandfather's farm. The farm started in 1860's from a sale of a land grant. My family still has most of it and it's rented out. Because I'm from a big family, each member would get only $5000/year in rent. Or...

MoKelly, Same here. My wife and I are on the same plan, both were out this morning. In ten mins, my came on. Hers didn't come on for 3 hours! It was a pain because she was at the hospital to see her dad

The sheets are 13 gage, .089, 304, the sheets are marked. mill finish I'm in Bloomington IN I ventured in to FB Market place. There is a seller listed as local with a huge selection of sheet metal, all looks new and on pallets. but no such business exists in our small town. Is this a sign of a...

I have 21 sheets of 13 gage, (0.089 inch), 4 x 10 feet Not sure if anyone would even want it all! yes cash and carry, I think each sheet is 144 lbs.

Thanks for all the comments I got the sheets of steel when the factory I worked at closed. The last remaining employees got to take their pick from huge piles. The good part is the steel has an ink ID mark. I might have a contact at a local water jet fab shop. They may know of users of this gage

Hi All, I have never been on Face Book and it sounds like Craigslist has gone south. I'm cleaning out my basement shop and I have a few items that are worth far more than scrap. I have a sister in law with a FB account and I suppose she could list it for me on Face Book Market place For...

pouring a footer and laying concrete blocks under the door makes that go away.

I have a lab dog story from 45 years ago. I wrote it down in 2014 so I wouldn't forget the details. Adventures of Mister Dog On this fine Saturday in 1982, my girlfriend and I had a friend over for a visit, it started with a nice cup of coffee and a joint. As we chatted we played a bit of...

We built a poured concrete home and we were mouse free for several years. Then, the mice began chewing through the garage door rubber gaskets. We have 3 garage doors, one on a walk out basement for my shop. I looked at the shop door and gasket and found the gasket attached via a tract on the...

I second the Xylene to soften all paints. for fun I gathered up several old paint brushes that I had found in bean cans I had forgotten about. A good soak over night and using a brush comb and they were back to life. You do have to wrap they in stiff paperboard to get the shape back. For...

I watched the video again I think I better under stand. He saw the fuel pump inject plunger for cyl #1 rise. Then he rotated the front crank pully to be in line with TDC. My injector pump does not have an inspection cover like his. So I will pull the fuel lines on the old pump and rotate engine...

my flywheel inspection port is covered by the front end loader frame. Its a big deal to remove it. I recall reading TDC is when both valves are closed and rockers are loose. Then can I look at the timing marks on the gears to get exact?

Thanks guys! If the TDC can be found by the #1 cylinder valves both being closed, then I won't need to remove radiator. Also, if I start the process at TDC, the only timing marks will be the pump drive gear.

Bob, The first question I had was relating fuel getting into the engine oil, engine lubrication system. As you know from my previous thread, my pump oil was being diluted by diesel fuel. I recall you speculated the high pressure side was lap fitted and they can leak in to the injector pump oil...

As noted on another thread, I have ordered a new injection pump for my KAMA 454 with a 395 T FD engine. I looked at Circle G tractor parts on line instruction. looks to simple...

Just to understand, if the pump in not lubed by engine oil, fuel can't mix with engine oil? If he has an oil reservoir on his pump, can it also be duel lubed by engine oil system?

Follow up. I was able to order the injector pump. It took a lot of back and forth. The pump was about $100 and UPS shipping $80. I understand installing one of these is not real simple so I'll plan the time slot carefully.

It used to be a brick and mortar store came with some level of expertise. Now it's just kids that don't know anything. Why pay higher price? NAPA had my Kubota air filter for $69, Amazon had it for $23 we do still have a few old hardware type stores that have 6-7 employees manning the store...

We fought wash outs for years on our steep hill. Our drive is what we call "53's". It's chip, dust and stone. In southern IN, it's all limestone. It does pack like concrete, but heavy rains can over whelm it and cause ruts. Parks departments use a swale/speed bump system to divert the water...

Our company got phished and sent a $150,000. check to a Russian bank! A few weeks later we were asked to an online training. But my company E-mail looked so suspicious that I sent it to IT for review. It had all the calling cards of a phishing scam, 1) Sender was a generic, Admin@company.com...

Bob, Have you ever bought parts from AliExpress? Though I'm an ME, I have worked my entire career in high voltage substation porcelain insulators.

Bob, when I installed the new ele pump, I did take off the mechanical lift pump and replaced it with a plate a gasket as directed above. I do have compression release and assume this would shut off the run away engine. Though I'm a mechanical engineer, I would likely fall into the novice category.

Follow up. Electric pump still works great. but I see I still have diesel diluting the injector pump oil. Tractor runs great I have only used the tractor for 10 hours in the last year or 2. Yesterday, I pull the dipstick on the injector pump and fuel gushed out. I assume this confirms the...

we like Buffalo Chicken flavor but Buffalo Wings are all bones and skin, and expensive. We chop up boneless/skinless chicken thighs and sizzle it up with butter and buffalo sauce. Put a scoop on a wheat taco skin with blue cheese dressing and a hand full of chopped celery. Same thing as...

I agree with gardening is a hobby. A bit like fishing. I do enjoy it so we plant selectively every year. I like to plant things that are either easy to grow or hard to get good produce. We are no till. Just a 70 ft long 2 foot wide strip covered in mulch with irrigation tubes. I can mow right...

I like my Doc Martins but I don't know where they are made. Real sturdy work shoe

Copy, Before the pandemic, I would go to China 2 times a year. It was always special to eat those soup dumplings. The trick was how to eat them with loosing the soup. After many years of traveling to China alone, I brought my wife. her first meal in Shanghai was in a small dumpling shop. They...

Newbury, I have several 1 to 2 gallon sprayers, big box store types, nothing special. I have several because I don't mix tanks that could contaminate another. They are all working fine. The only time I had issues was when I bought an expensive type, "made just for acid". From day one I had...

we had spigot at the well head to water our garden. The pressure is equal on entire line. I would recommend a check valve to keep and back flow out

dj1701, I agree. Years ago I would be offered something I thought I'd bring it back to life. When we moved, alot of that junk went to the scrap yard. Every once in a while I'll go look for something I had saved for a decade but ended up scraping it. You'd think I would be kicking myself at that...

If a truck stays dependable, you keep it. To keep your truck dependable, replace parts that are likely to strand you. I have a 2013 Tahoe with 175k mi. I have changed the fuel pump and the starter because it's a Chevy issue at 150k mi.

As mentioned above, very large compost piles with water filled tubing has been used to heat green houses. The material mix, saw dust and wood chips has to be controlled with water infusion and nitrogen to keep it hot. but a well constructed compost pile can generate heat all through the cold season.

LD1, You are likely correct about our 53's. There are some large rock in there. Once they surface it is an issue. Grading packed 53's is tricky. It must be moist to really get a bite and mix it back up. if to dry, you have a blade full of marbles! Cost for stone here is pretty cheep, Last time...

Here in southern IN, crushed limestone. Below is what I have used #2, clean larger than golf ball, 2 x 3in? new drive way base #5, clean 3/4 in, dustless flat drives, drainage rock #7, clean 5/8 in, dustless flat drives, drainage rock #53's, #5's and down with a lot of dust, well packed...

we had an old hand me down 90's Mercury sable that would "lock the doors for you". because we live in the country, we never take the keys out of our cars. So this happened once with my kids parking it and I did the wedge thing. But when it happened to me while just moving it, I added a special...

I would like to have discounted time of use. We live in a concrete house and it holds the cool or heat. So heating any time works. It's called the Flywheel Effect

CityDude, My wife and I like our bourbon. Enough that when we travel, we pack a bottle. Sam's club is where we buy our bourbon. Good bourbon for a great price; Buffalo Trace, 1792, Eligh Craig and Bullet. All under $27

what size drain pipe? I use 2" pipe to 4 in sewer and 1-1/2 P trap

I had a pile of limestone dust, on ice it was like white mud and did not help much. I'd think crushed stone "11's" would be much better, about the size of small pea gravel

I fight the same issue of cold fingers and toes. Mine turn white and I'm done until I get circulation again. Warm, not hot water helps. But I have found if I flick my hands down for several minuets, it forces the blood to my finger ends. This never happens during hard work, just sitting on...

Thank you Kenmac

All, I'm back. I cleaned the burners. I removed the two orfaces and cleaned them. Cleaned the piolet as well. I did a test fire with out the logs. Front flame is better but I'd think it should be better.

Thanks Jaxs

We have a 10 year old gas fireplace, propane. The front burner has very low blue flames but the back burner has nice natural flame look. This morning, the front burner did not even come on at all. Shut it down and restarted. Small front blue flames returned. Is this just needing a good...

Interesting to see several members working in the electrical power field. I'm a porcelain insulator engineer. Most of our products are for 245kV and above. The 765 kV insulators are 185 inches tall!

RSKY I lost my baby girl one time. I asked my wife if she'd seen her. She said "yes", your holding her! My arm was some numb from holding her so long! I was 25 years old.

Electric boiler radiant heat in slabs. Costs $100 a month per 1000sq-ft of house in winter. house is larger than 1000 sq-ft

No online presence in the carving world. I did make an Ester Island head that turned ot good. I'll find a photo. I can give you a bunch of tips how to start carving. But i'm off on a biz trip.

empty nesters, and plenty of hobby time! Thanks for encouragement to keep at it

high Eddie, My wet stone carving area is a mainly a 4 x 8ft steel table frame with a roof rubber tub below. From there a drain to a 5 gal bucket, then to an outside gray water drain. The bucket catches most of the solids. On the table I have converted a 10 in Craftsmen Radial arm saw to a 12...

Riptides, post a photo. Years ago, I used a jackhammer to remove an old slab footer combo. There was some steel, but not what you think of. I found old wrenches and other steel iron junk. None of it helped build strength. Did you put steel in it?, yup" One time I found a 30+ year old...

Thanks all. Riptides, Removing a slab?

We live 1 mi back on a private road I was waiting for a passport, Fed-X delivered to an unoccupied neighbor's lake house. That took a few day to figure out Fed-X never delivers boxes, claims no one was home. I work from home.... UPS, great service and used to call ahead so we could get our...

Carver, Not sure I saw a question. But I would no skimp on your poured wall height. Our walls are 12 ft poured, 2 ft bar joist that makes for 10 ft ceilings. We did have to remove 4 ft of sand stone to get it.

Civilian, The handrail around the upstairs hallway blocks off the "cat walk". But I know once kids get a bit bolder, they can climb over the handrail. That ledge serves two purposes, one is a scary place to get to window washing! It's 2 feet wide but feels like 1 foot when your on it. I have...

All, Sorry for the late reply. Installed the last vents yesterday. But all done without issues. Yes, our house is made from ICF blocks. walkout Basement and two floors above. Flat roof with a staircase to it. Future roof top patio over looking a large Indiana lake. All but some interior...

I glad to say, I got the vent in. I used a 1 inch drill to make the perimeter and a 1-1/2 drill for rows in the field. With large holes, my drill on chisel mode fit in the holes and busted the webbing. All was going good until I hit a 1/2 inch re-bar. But I exposed it and cut it off.

I have to thank my wife for choosing the the extra quite bath fan with a 6 inch vent pipe.

ponytug, I'm with you, I don't like cutting holes in my flat roof. That is why I have put this off for 10 years! Amazing we have managed with out vents. I did cut a pc of drywall in my ceiling so I can tweek the pipes. As a side note, removing the webbing between holes using a smaller bit...

If the roof was just bare concrete and not finished inside, core drilling might be considered. But as I have said, there is 4 inches of foam on top and living space below. So no water and no way I know of core drilling free hand. Like most flat roofs there is no attic, just 24 inch tall steel...

Eddie, My drill is a Hitachi, DH 38 YE. It's a monster drill, speed to drill is not a problem The hole through the roof is for a 6 inch dia bath vent fan. Our roof was poured and that vent hole was missed. It's a rubber roof so I will be using a Firestone "peal and stick" primer activated...

I'm drilling through a concrete roof with 4 in of foam/OSB/roof rubber on top. So back to my question, what drill pattern works best?

I have a concrete house and had to drill quite a few holes over time. I have a commercial grade splined shaft hammer drill. Bits from 1/2 in to 1 in I can drill holes quite fast, so that's not the issue. In the past I would drill the circumference and then the long process of drilling...

How deep is the top of the pipe? I would think a pen light on a cord and this number could be had. Then, is it soil or rock down to that level? Soil, Dig a hole, cut the casing to expose the pipe. Pull well pipe, weld new casing, fill hole? replace pump

I used green spray paint when a worker claimed my speed square was their speed square.

retire now, 5 years early. No other changes

To get peaches, the stars need to be perfectly aligned! Here in the mid west we fight everything. First year we planted 3 trees no bigger trunk than your little finger, some how picked two nice peaches. They grew to 6 feet tall and shaped to an open center Year two 1000's a blooms but OFM...

What type of peach tree? Some peaches are prone to pit split. I have not noticed any issues with over watering during pit hardening, during that time the fruit does not get bigger. Lack of fruit is more likely caused by a heavy set last year. The tree works so hard to make all that fruit, it...

Hobby peach tree grower here. We have 3 peach trees, if I didn't spray 8 times, I wouldn't get eatable peaches. If I didn't apply the first 3 sprays, I wouldn't get a single peach. They just drop after the bugs move in. Peach trees are heavy feeders, so I have to fertilize twice a year. Some...

after 40 years I final had to retire my first one. Always had it on my belt. Even took it on business trips around the world. the pliers got a bit too wanky. The new one has a lot more tools and locks the tools in position, so a major upgrade from basic model. I used to carry a Buck 110 but it...

I suggested using all thread as a simple gear puller near the beginning of this thread these two balls would have been removed a long time ago. But we would have missed out on all the Darwin award methods

very cool cannon. You could have a machine shop get it out or DIY Drill a hole in the ball, looks like a 24 to 30 inch drill bit would do it. To drill the center, you could cut a 12 inch long 4 x 4 to a square that just fits in side. Drill hole down the center. Or just use a flash light try to...

Ponytug, First, I'll tell you what I have and the critters we had aimed to keep out at the time of building. Our first issue was with the deer. We live on a lake surrounded by deep forests. We had 6 ft dia cages, 5 ft tall. The wire is welded 2 x 4 in openings. That reduced the browsing...

OP here, I'm embarrass to say it was a faulty tester! The new one was arcing the same at the charger. Both had about an 1/8 spark jump. The tester was erratic. I took the tester and the chargers, new and old to a dark room. The tester lights were very dim, but I could see them in the dark. All 5...

I see a charger at Tractor supply that is a bit higher energy, I get it and zap the 'coons"

Peaches are coming on and I'm having electric fence issues. last night I was testing the fence and found I was not getting a pulse every second, maybe every 4 seconds. The charger is clicking/light flashing every second. I used the tester on the fence and "sometimes" I would get a full reading...

I'm a mechanical engineer so I should be able to fix things. I like the challenge. Last year, I had a leaking injector pump. Everyone said "just replace the pump, they are nearly impossible to fix". But $10 in O-rings and careful cleaning and it stopped leaking.

that is what I hoped! I now have a replacement starter. Thanks for letting me know

I had an old starter and decided to take it apart and "fix it" to be a spare. I saw the problem was a broken insulator bushing that secures the contact. I made a new bushing out of fiberglass sheet stock. I thought I had learned a lot about solenoids having it a part. The solenoid has two...

I have done it many times. The trick is to use an accurate amount of water from the start. You will find out quickly if the next batch need more/less water. Guessing or keep adding water is a lot of work.

they come in different sizes, use ones that are relatively tight fit to your hose.

man wakes up on Father's day and says to his wife, "we could make sweet love or I could go fishing" Wife says, "I'll pack you a nice lunch"

OP, Plastic nut or brass? Garden stores sell washers, as well as any big box store

Not sure why this is so hard to diagnose. Because the OP won't share where it's leaking. let's start with eliminating the components. also, anyone suggesting teflon tape does not know how water hose connection work. The threads only pull the sealing surfaces together against the rubber gasket...

I like it, but they have so many exists you might get hit from behind! My trick requires a helper, my 10 year old jack Russell. I have a few 4 inch pipes under my deck. When I let my dog out, he checks to see if there are any critters in the pipe. If yes, he barks. I then go down to do my part...

Looks like I could go with either. The DOT tank would have a limited life due to the number of recertification's allowed. I thought I read 3 recert's allowed. I assume the ASME tanks cost more. The DOT tank was just $711.

Hi all, Amerigas is making the minimum propane purchase difficult. We need to buy 2 x water capacity to avoid the $177 yearly rental. If you dip below 20%, they can charge for a leak test. We use it for a gas fireplace only I thinking about just buying my own tank and let them have their tank...

I'll add folks build on a private gravel road and then want everyone to drive 5 mph past their house!

even if I thought I would die at 68, I would not draw at 62. Why? Because my wife could live to her late 80's on 70% of what it could have been. Drawing early has big penalties long term Even if my wife started drawing her S.S. early, when she chose to take "half" mine, it is reduced. 70% of...

oldsnio, Thank you. I'll plant the grass shortly and keep an eye on it. It's only 2000 sq-ft If it looks like the rye is crowding the grass, I'll weed-wack it down as soon as I see the rye flowers

I planted Winter Rye, not rye grass but the cereal grain, to stop erosion on a steep hillside. This was last Fall and it did a great job sprouting fast and holding the soil. Once spring arrives the Rye will grow again to make grain and will die off once it gets hot. Now the issue. I now want to...

I have 2 buck 110 knifes with broken blades. I'm sure they were not defective. Should I feel bad to get new blades put on?

Unless you mouse proof a building, catching mice is an endless job. I had two places that I finally found where they were getting in our house. First was they chewed through the rubber garage door gasket at the corners. To solve this one, I ripped oak sticks and screwed them just in front of...

we live in southern IN and it missed us. But I do wonder how our concrete house would fair. The main structure is poured concrete, floors/walls and roof with 8 tons of re-bar. The garage/porches and some overhangs are wood construction and would assume they would have been stripped off.

OP, depending on how long your lines are and just how accurate you want to be is the question. We marked our lines by this method. our land was 330 ft by 1300 ft. First, we found the corner stakes by walking with a compass. We knew where one was when we started, at the road. Walked off the 330...

Bob, From RonMar I found on Tractorbynet; "Because of the space limitations on the lower radiator hose this might be easier to install. It looks like it could be connected between the block drain on the left rear of the engine block and a "T" placed in the small recirc hose line that runs...

If I go for the circulating type, would I add a barb fitting where the block drain is and Tee in to short hose that feeds below the thermostat? Or block drain to lower Rad hose, they are about the same height. Where are you located? here in IN, we get plenty of single digits. My oil pan is...

I posted this question many years ago, but maybe someone out there has installed a freeze plug block heater on a KAMA 454. I'd just go for a lower radiator hose heater but the hose is very short. The engine is listed as a 395, not sure if the Shandong engine is used on other tractors. The...

I got the pump on and works great. And easy to prime!

we have a small garden to enjoy some fresh vegies. We don't till, just dig a hole in the lawn and plant a tomato, we might have 6 plants. Same with cucumbers but along a fence. For a few months we have all the tomatoes and cukes we want. Only a few hours to plant. No need to weed. The real...

Bob, I have a Wix 33528 fuel filter just before the lift pump. Thanks again for all your help

Bob, Thanks again for all your input. I have read reviews of many of the lift pumps, most have pretty bad reviews. Like worked for 3 months, or even worked for 30 min. Then I thought a pump made for OEM might be designed for long life might be better. First look was ACDelco, but they had...

I tried the 6 x 6, 5 ft tall reinforcement wire making a 6 ft dia circle around each tree. It did keep the deer out but, made it nearly impossible to prune and spray the trees. Also, making a tree grow tall to be above the deer makes it a pain to prune/spray/pick fruit. I keep my peach trees 8...

makes sense to take it off.

Bob, Thank you so much. I suppose I could just leave the old lift pump on and plug the holes.

Bob, Thanks again for all your help. Your bottom most note; that line comes from my spin on fuel filter. So it looks like I connect the yellow hose to the intake of the electric pump then goes to secondary filter. Then connect the outlet of the 2nd filter to red line. Green line gets moved to...

Thank you Bob and Jacques, good suggestions. Is the return line shown by the Red arrow? Is the lift pump where the primer pump is? Or on the left side? what line would the electric pump be added? Regards to bleeding, there is a hex nut on top that works fine with the hand primer.

Bob, The KAMA has a fuel return to the tank off the injectors. The lines on the injectors were replaced early on but are just the way it came. I did add a spin on fuel filter many years ago I will put a pan under the pump and pull the drain with the tank shut off. My gut feel is a lot of fuel...

Hello all, I have been getting my KAMA 454 ready for winter. I changed the gear oil in the axels and tranny, Changed the engine oil. Filled the fuel tank. Then the bad news came when I pulled the dip stick for the injector pump! Diesel shot out of the dipstick hole. I mean it just flows out...

HawkinsHollow, Comments about efficiency is either a truth or not. opinions do not come into play in physics. You made a comment regarding saving money by using such a device. Your friends here just informed you that there are no cost savings. One point I did not see yet was, the Heat pump is...

I was 21 years old, no longer interested in the university degree I was working on. So a rainy fall day I stopped in a realtors office, they had no interest in me. One block later I stopped at another one. Older friendly guy had me sit in his office and he read off a list of 5 to 10 ac lots for...

My dog was hit many years ago. It was not the drivers fault. A family friend was staying the night and walked the 1000 ft to our mail box to get the newspaper. My dog followed and got hit. Both were nearly deaf. It happens.....

I ride the metro in China when I travel there. Everyone is glued to their phones. I see couples eating dinner together, and both are glued to their phones.

Newbury, What costs dropped? I read an blog that listed the top 10 items where your retired cost drop, no one applied to me.

Doug, We feel the same. The only thing I see is we will not be contributing 15% of the paycheck to the 401k Down sizing is the only way we can reduce expenses. Big house = high utility, high taxes and high insurance.

same here, last year I got a load of #53 on my hill, almost no fines. They delivered a load of dust and chips at no cost. I had to "work in". Big pain

On our Southern Indiana hills, we need the fines. Otherwise it's like spinning on marbles. The flat areas near the house we use just 3/4 inch rock with almost no fines.

See link from AARP. 10 myths about Social Security. Also, there is no income threshold if you are FRA https://www.aarp.org/retirement/social-security/info-2020/10-myths-explained.html

Ultrarunner, A key point often overlooked is thinking about spouses. For example; a few years back your spouse could start collecting the reduced payment at 62 while you keep working, then switch to "half" of yours when you retire. But now if the spouse retires early, their payment when they...

Hello all, I have a 1967 John Deer 112 garden tractor, round fender. I have contacted our local Monroe County, Indiana 4H to see if any young 4H'er was wanting a project. No reply's.. My grand father bought it new and he used it until he was 105 years old, died at 108. Stored inside until 2008...

well it looks like I'll need to replant in a month. Lows have been 70 degrees

Good day, I had some earth work done and it created a slope that needed erosion control. Winter Rye, not annual rye grass, was highly recommended for it's aggressive roots and fast germination. I dampened the soil, spread the seed, raked it in and covered with straw. Due to the heat and lack...

Steppenwolfe, Yes, in many cases we can be born in "less than ideal" conditions and by true grit make a prosperous great life. So many people also have made a bad decision and got caught, served their country and came back damaged or grew up in an abused family and so on. Only to image how...

Retirement planning is well documented. Sure, save early. Easier said than done for some. I grew up in a nice neighborhood in the 60's and 70's. Dad was an engineer, so I became one too. Go figure. Life has been great, big house and bigger 401K As I skated through life, doing somethings...

Mat4644, We have 16 of these and 3 failed after 10 years.

Wow, all good suggestions.

Hello, I have 3 large triple pane window glass panels that need to be replaced. The insulated glass panels are manufactured in Denver, 1000 miles from me. And before you ask about getting made local, they are special heat mirror film as the inner "3rd" pane. The life time warranty was lost when...

Last week my wife was cleaning some of our casement windows and noticed one would not open. It was sagging a bit and I first thought it was stuck. My wife, smarter than me many times noticed the latch handle was not going to the full open position. No I didn't force it and break the handle! I...

RSKY, Wow, what a story. We have a few sets of those knives. Even gave them to all our kids, but with clear warnings, those bad boys are the sharpest knife. I've trimmed a few finger tips, but near as bad. Funny though; when my wife read the knife reviews, one review was very bad because they...

I think a lot of the problems people have using wire nuts could be eliminated by good planning. I like to run a circuit to each room. The ceiling light has a large box for junctions. I don't like to have the light fixture wires in the junctions. I pig tail makes just the final connection easy to...

As others have said, the first sprays are often the most important. In the Fall and early spring before bloom, Dormant Oils are useful. Some fruit trees benefit fungicide sprays at bud first pink. Avoid most sprays during flowering stage to let your pollinators do their work. For insects, fist...

I did contact thepumpguysc, he does not sell parts

They sell pumps, but not parts for them. I found a O-ring calculator at; https://dsportmag.com/the-tech/education/engine-tech-o-ring-measuring-and-material/ The top O-ring cross section measures small compared to the formula, this likely where it's leaking

Hello all, I have a leak on my Chinese tractor injection pump, KAMA 454. The leak is on the top side at the delivery valves. There are 3 sizes and a crush washer. I can't get parts for this, just a replacement pump. Do you trust NAPA O-rings? Do you think just taking measurements will net the...

Is the floor stained? if not, sand the surface to hit the dirt. you might need to use a real light yell stain to get the aged color. Then match the gloss level. You will likely need to refinish in the future but this can delay the need.

Pettrix, check codes first. But The point of a footer is to spread out the load. So increasing the width is also a big driver. Use well placed rebar on chairs with minimum overlaps. And make sure concrete is not poured on lose/soft soil. A poured wall will act like a beam vs. CMU wall, and can...

hello, I have a Stihl FS 55 weed trimmer and it's 12+ years old. I have had good performance from this beast. At the end of this season, I planned to run the tank dry to store it for the winter. It was easy to start all season. But it it sat for 2 months before I got around to getting it ready...

I posted this topic on the Chain saw site, but didn't get any interest. I had 10-15 trees get closer to our house : ) They looked small when I decided not to to clear that far back, had really grown and leaned towards the house. These are oak, cherry and beach that were 50+ feet tall. Two were...

just got my chain back from being sharpened, and the teeth are nearly ground to the limit! This was a new chain and was just starting to show signs it needed sharpening. normally, I just pull out the dremal and touch it up. Because I'm dropping trees, I didn't want it to cut in a curve. I took...

Hello all. I've got an electrical issue with my old G5200. After resting all winter, I charged the battery ready to cut a bit of grass. Turned the key and nothing. I noticed the fusible link was burned through. With the key off, I jumped the fuse link, but it sparked a bit, so I assumed I had...

Anyone cancel travel to China? I was booked to fly to China Fed 15th but will delay until summer. I'm pretty impressed the lockdown of most of Hubei province has kept most of the infected and death to one region. John Hopkins has a good website for tracking. Operations Dashboard for ArcGIS

Around here, southern Indiana, we use what is called 53's for driveways stone with chip and dust. Or # 5's and #7's with about 30% chip and dust. Others call it "crusher run", I recall. In the hills of Southern Indiana, you must use a crushed stone that can be compacted. Last Monday I had a...

Anyone know where to get an after market PTO double pulley for the G5200? I can't find a good parts diagram to even get the OEM part number. Or if anyone knows the OEM part number.

Good day First I must say peach trees grow so fast and you can see results of your work so quickly. The first growing season we bought 3 trees 2-3 ft tall Red Havens from our local grocery store. The sticks were about 1/2 inch dia. Read up on open center shaping and the fun began. First year...

good day, I have a deck with steel "painted" posts. The raccoons climb up and cause all sorts of trouble. Yes, I have killed them by traps. But they are getting smarter. I want to place a "hot loop" like a halo at the top of each post. I would run the hot under the deck on insulators. Then I...

I think we know most of the important items, Like don't forget to have plenty of the essentials, like beer. Joking aide, I hate to have my car/truck door gaskets freeze and get ripped off as I try to open the door. So I simple oil them with; 3 in 1, Vaseline, even olive oil! No matter how cold...

I have a KAMA 454, 45 hp with a 3 cylinder diesel. I have noticed where the lines come out of the top of the injector pump, they are leaking. It's not the nut where the line tightens but under the hex just below. see photo. With tractor off, you can see the leak by using the priming pump. When...

Local story where a guy is getting a bill for $9000 for his half of a line fence. It's already gone through the Township trustee and will be levied on his taxes. He has only 9 ac. His neighbor wants to start raising cattle and is using Indiana fencing laws to force him to pay half. Some of the...

Hello all. New to the concept so I thought I'd ask here. I'm looking for an alarm system that requires no monthly plan. I want it to send us a "notification" if; 1 One of the doors is opened. I have wires run to each of the doors now. Due to long distances, I don't think wireless would work. 2...

I have a 2013 Chevy Tahoe, former police car, with 160k miles. 99% of the time, when I drive it I'm off to the airport or on a business trip. So any break down would cause me to either miss a flight or miss meetings/and have to have it towed/wait days to get it fixed. The Tahoe is in excellent...

We were recently in the Tetons and Yellowstone areas and saw a lot of fly fishers along the small rivers. We staoped as a guy was catching a fish. Turned out to be a white fish. I have played with a fly rig, but I roll cast. That is where you get the end of the line out there by whipping the...

I have bought two diamond 4 in dia cup wheels in the last two years. Both have been so out of balance they were not safe to operate. The first one vibrated the screws out of my angle grinder, not to mention my hand felt numb. I took it back The second one was today. I was mounting on a 5/8-11...

I have been recently been re-united with my grand father's JD 112. It looks to be from 1969. He died in 2008 at 108 years old. My BIL had it for the last 10 years. But mostly sat under a tarp. Mower deck is real solid and mainly rust free Known issues are engine blows out oil through the...

I'm guilty of not spraying my peach trees yet, between raining and travel, I missed it. Now I see oozing peaches all over. I'd say most of them. The trees were planted last spring and this year the trees were covered with blooms and soon after the peaches. What should I do? Pick off all the...

I just planted a Nectarine tree and trimmed it up. I have seen where you CAN start new trees from cuttings. The little branches I cut have started to leaf out. I removed the 2 leaf buds on the lower part. Am I too early, too late? There may be a down side to all this even if they grow. Often...

I'm looking to mount a face plate where the drill chuck would go. The thread is 1/2-20

I don't ever remember having ticks as early as March 20th. Then today, 3 in of snow. just not right.

With our 6 peach and Cherry trees looking good, we are thinking deer fencing. Currently, we have 6 ft dia, 5 ft tall cages around each tree. The deer eat anything hanging out the fence. This year, the trees will out grow the cages. And if lucky get a small crop of peaches. Points to consider...

To all the peach tree owners. We planted 3 peach trees last spring, they were sold in a 1 gal container and had a trunk the size of a broom stick. They were a bit over 3 ft tall. We trimmed a bit to get the desired open center. With good watering and twice fertilizing, we had good growth. All...

I've had a raccoon arrive "uninvited". I caught it drove it a few miles away. It came back in in 2 days. Turned out the 3 mile drive was only 6000 ft as the crow flies. Today I caught it again and drove it 3.5 miles, "as the crow flies". I hear 5 miles is the minimum but can't think of a place...

We did a test in our basement a while back and had high readings. I can't recall what our reading was at the time. But my wife is pushing to do something about it. We ordered a tester; InspectUSA.com Electronic Radon Gas Detector and Alarm (HS71512) EPA Approved I figured I want to retest in...

Hello all, I'm having air compressor issues. I have good tank pressure but I can't regulate the pressure down. When I turn the regulator knob counter clockwise it leaks out the bottom of the regulator. Model, Campbell Hausfeld HJ300101 In the photo, the regulator is a part of a manifold. No...

On Friday, my wife and I were enjoying a 5:00 bourbon on the covered back porch. Our Jack Russel, Henry, chased off what we thought was a dove. A few minuets later a pigeon landed on the table and started walking towards us. Our first reaction was to chase it off. But we saw the bright red bands...

I needed to grind some concrete slab edges so I bought a 4" diamond cup wheel. I have one for my 7" angle grinder and they are great. When I first started it, I noticed some vibration. I figured after a bit of use it would settle down. After 5 min of use I stopped to give my hands a rest due to...

I'm have a truck load of 53's/crusher runs, laid today. I filled in the holes and ruts first so I start with a reasonably flat drive. But normally it's nice to "touch it up" before it's all packed in. If you do to much grading, the bigger rock ends up on top. Racking is the worst. I'm planning...

I have a Stihl FS 55 R weed trimmer. Great machine for the last 10 years or so. But every 5 years or so, the beast slows down, or gets difficult to start. The first time it did this, I bought the rebuild kit and cleaned it. No improvement at all. Tore it down again thinking I must have missed...

I'm in charge in providing the Groom dinner the night before the wedding. It's a destination wedding at a ski resort in Colorado. We are renting a large house very near the venue hosting the wedding. So we plan to have the dinner catered at the rental house. This is just immediate family and...