Search results

Hello, I've stripped down my Iseki TX2140 about a week ago to change the clutch. Mostly all back together, however I'm clearly going senile as I can't remember what linkage goes where on the throttle, doh. I was unable to get the whole rods and levers as one photo as the FEL bits are in the...

I'm looking for links to someone in the UK who can supply a replacement hydraulic pump for my TX2140 please? I'll get the fixing PCD and what is written on the back later. Thanks in advance of any help :)

I've seen somewhere in the past, where someone had identified equivalents for the three separate items (clutch plate, thrust bearing and pressure plate). I think Vauxhall was mentioned. Can anyone help me out with information please? Yes I could use an Iseki dealer, however their prices are a...

What's the easiest way to change the clutch please? I'm thinking the easiest is probably pull the radiator and move the engine forward. Or is there an easier way? The tractor has a sub frame assembly for the front end loader and rear back actor. Also... Whats the part numbers for the following...

I thought Iseki and Kubota engines were the same, but they're not, however I'm wondering if the flywheels are the same? Would someone who has their 3 cylinder diesel engine out, be able to take some dimensions for me please? Can I have the following dimensions please?; Outside...

A friend has bought a TL2100 and now trying to find her way around it. I've not seen this tractor myself, so difficult for me to answer, sorry. First, what is the right angled lever on the right hand side of the steering column below the key switch please? Second, does this model have a...

Does anyone know what make the valve chests are on the Beaver FEL and back actor please? Or where I can get replacement rubber gaiters please? Thanks

Can anyone supply order codes/part numbers for... Fan/Alternator belt Engine oil filter Engine air filter Fuel filter (the one in the bowl) Thanks in advance Steve

I have an Iseki 2140 with a Polymark front end loader with a self levelling bucket. Has anyone engineered any sort of indicator to give the position of the bucket without having to lean over to look at the side of the bucket? Thanks for any useful ideas :)

I saw an advert somewhere in the UK for someone who made replacement ride on garden mower decks with choice of outlets (side or back) and galvanised. Can anyone point me in the right direction please? Thanks Photo is of the OEM deck

You may have seen my other post wanting a rear halfshaft or two and one has snapped, so the other may be on its way out. I suspect I'll work it out one I start getting my fingers dirty, but a heads up will be helpful please. Most halfshafts I've worked on, are held in place with a collar behind...

WANTED: Rear Halfshaft or two for Iseki tractor model TX2140 Can anyone help please? I'm in the UK

Hi Guy's Anyone know what max pressure I should be getting on the hydraulics please? My FEL and rear arms are not the strongest, so have fitted a gauge to see what pressure I'm getting (can't remember at present, so update later). As far as I'm aware, I think my hours meter has already...

I'm slowly getting around to registering my Iseki TX2140 for road legal use, so the Driving Licensing Authority are going to want numbers to create a registration document. I have found the frame/chassis number on the silver label by the gear stick (shifter), so to avoid taking all the guards...

I've seen a number of bucket designs by fellow members, many seem to be of an angular design. This has got me thinking, as I've always made mine with a rounded back and flat top as shown in the image below My reasoning for the flat top is that its then easy to see the bucket is flat and ready...

I'm wondering what other owners experiences are with starting their Iseki. Mine has the three cylinder Mitsi engine. I have to pre-heat for around 20 seconds before turning the engine over (ambient temperature is usually around 10 degrees centigrade). Anything shorter, it doesn't really want to...

tractor terror

These tractors were clearly designed for little people! Having slipped off the step, grabbing the first thing handy (gear lever) and almost getting squashed by my own tractor lurching forward (thankfully in low box), I thought it was time to sort the inadequate steps out, so here's the result...

Checking out the users handbook, it doesn't say to use any particular type of antifreeze, what's other owners opinion on what to use please? Thanks

I started a thread in the wrong place by mistake, so this is a redirect to it http://www.tractorbynet.com/forums/hydraulics/248248-pressure-releif-valve-front-loader-2.html Basically I think my hydraulics are under pressuure, but I'm struggling getting suitable informaion as my workshop manual...

On the back of my back of my Iseki I have a back actor/hoe that was made by Polymark (sussex) ltd, in the UK. The tractor has only just achieved 200 hours, so the back actor will be less and the tractor came with a rotavator. Anyway, looking around it over the weekend as I was doing some...

Hi Guy's, Clearly these lovely tractors are designed for little people! Yesterday I fitted a new 'sprung' seat to my TX2140 which is about 6-8" higher than the original. Having the seat higher than original was done on purpose as (being a tall guy) my knees were up by my ears (just kidding)...

In a different thread, some guys have been asking about my dual wheel adaptors, so I thought I'd post some photos showing the actual design. The following is a basic 3D image of the adaptor View end on View side on The adaptors have been made from 70mm (2.75") A/F hex bar, chopped off...

Can sks tell me where the machine data plate is on my Iseki tx2140 please? I've had a quick look around (its pouring with rain, so didn't hang around), but could not see anything obvious and there's no indication in the owners hand book. Hopefully it will give the machine serial number etc. so...

Okay, this may seem a stupid question to ask, so let me explain first. Its a new machine to me, its currently fitted with a back actor (rear end digger) with a hydraulic pump fitted to the rear PTO shaft so I can't see the actual PTO shaft as the pump drive coupling is push home. Also its...

Hi Guy's, Without spending a fortune, is there any TX2140 workshop manuals available, preferably on CD? At present I'm wishing to identify the parts (PRV etc.) in the hydraulics feeding the front loader. Thanks in advance

Hi guy's, I'm the new owner of an Iseki 2140, so trying to workout where everything is. I'm looking for the locations of the pressure relief valves on the hydraulics for my front loader. I've found the PRV on the control spool valve, however there must be another on the tractor somewhere, can...