Search results

These 2 blades have been replaced on my BX2680 that has 54 hours on it When they are laid flat, as in the pic, they will wobble when each end is pushed down. They seem to be bent symmetrically Also note there is not one chip out of the cutting edge of the blades which indicates they did not...

There is a Kelly Blue Book for tractors, but it is a pay site unlike the Kelly Blue Book for vehicles... Is there a site somewhere that I might get an approximation of the value of my BX2670/60" Deck/Loader on a trade-in?... Thanks...BCB

Is there a website similar to the Kelly Blue Book for vehicle, but for tractors? Particularly to attempt to find the value of a Kubota GR2020 gas engine model... Thanks...BCBSLICK

What might a fair price to charge, per hour, for the use of a 33 HP tractor with a brush hog... I have some fields that need brush hogged and I really don't know what to offer the guy who does it... Thanks... BCBSLICK

Will this tractor (BX2670--26HP) handle a Woods 48" rotary cutter? It weighs in a 400+ pounds... Any suggestions as to how much weight might need to be placed on the front end? Thanks...BCB

Don't know where to post this so I'll put it here... I am looking for suspenders, the kind that hold your pants up, that say "KUBOTA" on them... I've searched the Net and can't seem to find them. I find them with other manufactures, JD, International, etc, but NO Kubota... Any help...

I am looking to get a set of aluminum ramps for my BX2670. From the specs, I think the tractor, mower deck, loader, and operator would weigh about 2500 pounds I see ramps that handle 2000 pounds per axle. Does that mean those ramps could potentially handle a load of 4000 pounds--2000 pounds...

I'm lookin' at a 1025R I presently have a Kubota 2670 and I am a bit discouraged with it but not enough to go GREEN just for something to do and to spend more money I am concerned about the glow plug, or heating unit to help the tractor start in cold weather. It appears it stays on the same...

Does anyone have problems attaching these critters?... I can't get the valves on the quick coupler to release pressure on the loader side of the hydraulics... So, you can't get them to attach... I have tapped (hit) the nipple on the attachment coupler with at wooden dowel to help release the...

I have a 2670 and I was wondering if anyone uses a trickle charger on their tractor during the winter months?... Is it O.K. to let it on all winter?... Thanks--BCBSLICK...

Is there a trick to attaching and disconnecting the front end loader on a 2670?... I seem to have nothing but trouble I have the loader setting on fairly level ground. I line-up as near perfect as I can when I drive the tractor between the loader arms I do notice that the hoist cylinders are...

As with most of the dang tubeless tires on tractors, they get small thorns etc. and leak slowly... I am getting tired of putting air in the front tires of my Kubota 2670 so I want to put tubes in them... Checked at my local tire dealer (he is fairly big and I have purchased dozens and dozens...

Are there any type of heaters that can be used in the oil pan (hot dipstick) or something that can be put in the radiator to help the diesel on the 2670 start?... I really don't want to go the the expense of a block heater as there would really be few times I need it here in Western PA... I...

I'm looking for a sickle bar for my BX2670... I am wanting one that will cut at about a 45 degree angle, so I guess it has to be driven by a belt?... Is there a good place to look for one or to attempt to purchase one?... Brand names?... Do they run off of the rear or mid PTO...

Anyone know of a source of tail lights for Kubota or other tractors?... Thanks...BCBSLICK

Is there a site someplace that might give prices (tread-in values) of Kubota tractors?... Specifically, a 2350... Thanks...BCBSLICK