Search results

The tires are temporary, I will install tractor tires later

Shortening of the semi-axis. I didn't want to weld "butt to butt", I think this method is not reliable and the axis will break near the welding seam. I cut the axle to length, drilled the hole and pressed it in. Then drilled a hole, pressed a roller from the bearings into it as a key, and...

Additional reduction gear and PTO drive shaft. Used gears from a car.

Yes, this is a new project.

This way I got 8 forwards and 4 reverses

I used the gearbox from the car, dismantle 3-4 gears, they are now not necessary

Greetings. At the beginning of the summer I started building a garden tractor. His task was to mow the lawn, the result exceeded all my expectations, so I decided to do 4x4.

Hello. Two years ago I built this two-wheeled tractor. For all the time no changes on the two-wheeled tractor, the design turned out reliable. But on the rotator i modified the reducer, installed a smaller gear to reduce the speed of the knives.

Very soon there will be a combination of two parts of the transmission.

Continuation of the project

Hi. I start all over again. The transmission will be 100% new. I gave up the differential, I use two clutches for onboard turning.

Plow from the old propane balloon

Keyway and clamp

I set the reverse switch

Reverse gear

You did not understand correctly. First I do welding, and then I cut the hole for the bearing.

I like to work with gears.

The box is ready. The next step is to fill it with gears

Diameter of shaft 47mm, gears from the car. The next step is to install the seals on the shaft.

I worked very well today. Began to make a transmission. Gears from a car and a motorcycle. Sheet metal case with a thickness of 15 mm.

Photo report of the work performed

Hello. Began to build a two-wheeled tractor for work in the garden. 5.5-horsepower engine, gearbox and clutch from the Dniepr motorcycle. The axle and the lowering gearbox with a reverse and a shaft of power take-off will be homemade. The two wheel tractor will have 4 speeds forward and 4 backwards.

Fixing bearings. The next step will be the manufacture of brake support

Upgrade gearbox. Production PTO shaft

Transmission repaired

Transmission repair. Replacement of all bearings, synchronizers, switching plugs and clamps, secondary and primary shafts. Also repairs locking rear differential

Made Crane for my tractor

Installing the engine. Two stroke gasoline engine, 100cc 5 horsepower. I know it's a bad idea, but I do not have another engine. The engine made in 1982, but I set a new piston with the cylinder seals and bearings. After I'll change the compression ratio, set a petal valve and a new carburetor.

Homemade gearbox has 2 speeds, would be 2 speeds forward and 2 back.

I will be able to go near dumpers, or ride it standing. For this made footrest, if desired it can hide.

I began to collect all the parts into a whole

Wheels Manufacturing

I will use differential turn, that will be installed on each disc brake tracks. Stopping the left, the right will spin and thus will run turn dumpers. Tracks are made of old tires from the truck. I cut out the treadmill and cut a new tread.

As used gear rear axle of a motorcycle. It has a built-in differential and reverse. The structure of gear

Hello. I want to share my new project, it will be tracked mini dumper.

Hi. For my homemade tractor daily is work . I graduated from my new project built homemade walk-behind tractor. Chinese Engine 5.5 horsepower, transmission of the motorcycle. Walk-behind tractor has this description: speed 1 - 5.4 km/h;* 2 - 8.6 km/h;* 3 - 11.5 km/h;* 4 - 15.1 km/h;*...

Also during this time I built a new mower with hydraulic cylinder.

Now I'm building gear box. It will actuate an independent drive shaft. It will have two speeds, 500 and 1000 rpm. It remains to establish the clutch. This shaft will drive a mower, pump on the tank, and other devices.

Finished work on building homemade mower. Result satisfied, mower mows quickly and efficiently. I also decided to install the tractor hydraulics. Use a gear pumps НШ 10Б-3 with three section and distributor P80-3/1-222. The pump can be switched off at will, using spare parts from gears...

I Built a electric device for lifting. Maximum weight lifting was 110 kg, but I changed the transmission ratio thus increasing velocity but decreased weight. Now it is 80-90 kg.

If I'm not mistaken, the Haflinher is a small and lightweight car that is shown in the picture. Your Haflinger similar to our LuAZ-967. I used parts from LuAZ for building tractors because they are very reliable.

Camdigger, You must have 2 bearings. If you put less than 2 bearings, the transmission over time break down. I decided this problem so as shown in the picture

Camdigger I have no picture of the clutch. Engine combined with transmission via V-pulleys, slowed down against 4:1. System-disk clutch, V-belt pulley screwed bolted to the flywheel.

Thank you! Diesel engine Sadko DE300, 300cc and 6 horsepower

Snow removal. Device lifting shovels not installed so it does not rise. Snow was the rain, he chilled and tractors were hard to clean. I put to the test on the rear axle additional cargo weighing about 100 kg, the result was much better and less skating wheels. A little pictures at the end...

I also built a trailer and a shovel for his tractor

As donor parts I chose LuAZ 969m. Axles and gearbox , rear and front axle, side gear. Rear differential can be locked by desires. The frame is made of profile tractor 40x40. Wheels of motoblock, size 6x12

My tractor now looks like this. He is in me is not ready to be done on the brakes and electric attachments.

Sorry for Syntactic errors in the text, I speak English badly. I live in Ukraine which is located in Europe. *Long I read this forum, there are a lot of interesting information. Seeing homemade tractors on the forum, I decided to show his homemade mini garden tractor 4x4. *I used diesel Sadko...