Search results

Hi Folks, My steering connector rod is bent upward and wearing against a cover on the front differential casing. It has a jam nut holding the adjustment at each end. I think the jam nut on the left side is a left hand thread. What is the best way to break the jam nut loose at each end? I have...

Mangled seal #12 around bearing #11 tied the upper case to the lower one. Took about an 2 hours with a brass drift pin, and some surgical work with a small hardened steel chisel. Cases ok, new seal and bearing on the way. Everything else checked out good.

Good morning Randy, thanks again!

WM75Guy, Thank you so much for this! I think I will have to work backwards with this a bit and reinstall the vertical shaft, gear, bearing and bottom plate (#25, 26, 27, 28). Pulling those things out before before pulling the upper and lower case may have misaligned the bearing and seal...

Question about taking the right hand final drive/drive train housing apart. I removed the cover #4, unbolted tie rod, power steering cylinder. Removed lower cover #28, along with the shaft #25, gear #26, and bearing #27. I removed 21/22 arm. Removed case #13 upper drive train housing from axle...

Great! Thank you kindly JasperFrank! That is all the info I needed, and you are much appreciated! Hope you have a great day. Kind Regards, Steve

Thank you very much JF for your reply! So how do you release the stuff bearing, etc. that is to the other side of the ring. Thanks.

Hi Jasper Frank, Quick question for you on the diagram part #5 split ring retaining ring, how do you get the bevel gear to release from that ring? I know the bevel gear snaps in with pressure, does it work the opposite way? Thanks in advance! Kind Regards, Steve

bmaverick, Where do you get the ti-pars? Thanks, Steve

Folks, Quality tires for Land Pride Finish Mower? I saw the finish mower tire thread in the tire section, having a hard time finding a quality replacement tire set in size 4.10/3.50-4" All the ones I've seen are low quality tires with very poor ratings. Can someone steer me in the right...

Dear Folks, Need a comfortable replacement seat for a 2000 TC series NH, mine is a tc35. I have lower back problems, any thoughts would be much appreciated. Kind Regards, Steve

How do I locate the engine # on a 2001 TC 35 S tractor please? Many thanks in advance. Kind Regards, Steve

Dear Folks, TC35 tachometer not working, possible causes? Possible solutions? Thanks in advance! Kind Regards, Steve

2001 TC 35 does not have the hydrostatic transmission, it is the synchronized 12 x12. I have no dealer near me, the manual calls for NH 134D, is there something else that can be used? Thanks in advance! Kind Regards, Steve

Thank you very much THClimer, I have contacted Messick's in hopes of obtaining the seal and o-ring kit for this. See image of pump id numbers below. Kind Regards, Steve

I have a major problem. Was working today with my tc-35 and there is a drain tube that comes from the top of the engine on the right side, it is black vinyl, about 1" in diameter, it originates below the air cleaner, then drops down past the oil dip stick and fuel filter and is just open to the...

Hello Folks, My RPM gauge stopped working about 50 hours ago. What to look for for a fix? Thanks in advance. Kind Regards, Steve

Hi Folks, What is the best way to clean, de-oxidize and wax(?) my tc 35? The blue is starting to look like my grey hair! The black too! Thank you in advance! Kind Regards, Steve

Hello, I have looked at electric fence testers, $40 and up. Can a fence be tested with a cheaper multimeter? If so how do I do it? This is a battery 12 volt battery powered fence and I need to know when to recharge the deep cell battery. I have an extra battery for changing out but I don't...

Hello, What is the best way to go to convert from pins to quick attache on my tc-35 loader. Best regards, Steve

Hello, What size box blade can a tc 35 handle with out problems? Thanks again, Best Regards, Steve

Hello, I keep having problems with the safety switch on the left side of the transmission that is actuated by the forward reverse linkage. I have pulled it out, cleaned it and it works fine for a few days and then back to the old tricks. I tried to find it on a parts list with no luck. Has...

Ted, I would order today but you have not started a Peanut Fan Club with a free poster yet. A poster should be sent along with each implement. Hey Peanut! Keep smiling you done good! Best Regards, Steve

Hello Folks, I am looking for a small pto driven grain/corn grinder. Let me know what you may have. I am in the Pacific North West, Puget sound region. Can travel to pick up. Kind Regards, Steve Gill

Hello, I have a tc35, in the morning it starts right up. If I shut it down it will not start for 3 or 4 hours. But then it starts right up no problem? I can hear a slight click which seems to becoming from the right hand side of the tractor when I engae the ignition to the start position. Any...

Hello, I have a tc35 with the shuttle transmission. The clutch rusted up. I followed the "famous" rusted clutch thread. I tried breaking it loose by getting it in low gear and braking and brake steering. After that exercise I pulled the starter and sprayed the innards down with the "Blaster"...

Hello TBNers, Are there any other non NH alternatives to the various filter on my tc35a? The cost of these things are astronomical here. Each item has a shipping surcharge added to it as if the dealer had to order each one separately from the warehouse. Is there a Wix filter that will fit the...

Hello looking at the injection pump on my tc35a I see the pump is bolted on with 4 bolts. The top right bolt looks as though it has a screw tapped into the head of the bolt. Is that the bleeder screw? What type of driver does it take? I can't get close enough to it with reading glasses. Or...

Hello, Here is how this thing came about. 1 I was at work. 2 Temperature dropped, snow fell. 3 Wife got on tractor which was in the barn, it started she made it out of the barn 10 feet. 4 Tractor died 5 She discovered that the fuel filter was iced up. 6 she took it off the bowl and filter and...

Hello, How do I adjust the parking brake on an 2001 tc35. My wife left it on and ran it ,for a couple of weeks when I was gone. Now there is no holding no holding power. Best Regards, Steve

Hello, Does anyone have any experience with the Kipor brand of AC generators? Are they decent or? We have intermittant power outages here and we are looking to replace an old generator. Best regards, Steve

Hello, I noted that there is a discusssion in the "Attachement" area of this site and a persom with a kabota lost his loader bucket while backdragging. The pins could not take this type of usage. Has this happend with quick attache on any of the blue loaders? I was on the verge of buying the...

Hello, After reading the "tractor broke in half" thread I have a question. Am I putting my tractor in the position for this type of problem by having an 850 pound counter weight hooked to the three point? It is made with a barrel and has a top link. I used it when using the loader to do dirt...

Hello, I am wondering if a loader should drop when it is sitting with the bucket at full altitude with the tractor off? Last night I had about 20 sheets of OSB plywood on the forks at maximum altitude. The bucket dropped a foot in about 5 or 6 minutes. I had removed half the sheets in that time...

Hello, I have a tc35 with 16la loader. The tires are filled. What size counter weight should I make for the back? I plan on using concrete to make the weight. Does any one know the cubic foot weight of concrete cured? Much gratitude in advance. Best Regards, Steve

Hello, The bucket on my front-end loader has a three quarter inch bend up in the middle of the cutting edge. How would one go about straightening the bent portion of the bucket. It is messing up my grading efforts. It has been that way since I bought the tractor used. The bend is gradual along...

Hello, Does any one have any thoughts on the way to go for front forks on a tc35 with a 16la loader. The 16la does not have the quick release bucket. I will be using them to move pallets as well as lumber. Any thoughts will be much appreciated! Best Regards, Steve Gill tc35 45 acres

Hello Group, What degree of tilt is considered safe when on a hilllside with a tractor? I own a TC35 with filled tires. Best Regards, Steve Gill 45 acres NH TC35 Fel Rm PHD RR

Hello, What is the west way to adjust the clutch on the drive shaft of a rotaty type firld mower. It is on a Howse. Thank you in advance. Best Regards, Steve

Hello Folks, I have a quick question born out of ignorance of course! In my owners manual it says to check the tag on the transmission for the model number. The tag reads TC35S. The book says TC35, the decals on the tractor read TC35A? Are they all one and the same, or? Which do I use when...

72\" brush hog-rotary cutter TC35A Hello, Can I run a 72" rotary mower/brush hog on TC35A or is that over kill? I will be cutting blackberries and other heavier brush. Best Regards, Steve

Hello, I have a New Holland tc-35-a. Being ignorant of backhoe needs, here is my question. How many remotes need to be installed on the back for a backhoe? Can I run off the front loader lines? Is there a better hoe to get then the NH hoe? Thanks a bunch, Steve

Hello, I would like to thank this forum. I am relatively new to it but it really helped me to find the right tractor deal. I acquired a TC35 with NH 16la Fel for $12,500 it had 470 hours on it and was used on a small horse ranch for feeding. I will take delivery next Monday or Tuesday. To think...

Hello, does anyone have the specs for a JD 440 fel, its mounted on a 1070? Thanks, Steve

Hello, What is a fair price for a new 3520 Hydro with a 300cx loader? Thanks, SG

Hello, Can anyone tell me what the best quality fel for the price is for a tc40da? Best Regards, Steve

Hello, Has anyone had any experience with the TYM et 350? Who makes the engine? Is it a throw away tractor? Is it really 35hp? Best Regards, Steve

Hello, Is 19,000 to much to pay for a 2003 TC40D,Diesel,MFD with a NH loader? It has 1,000 hours on it. Best Regards, Steve