Search results

the smaller the tire the faster it spins

bought a barreto log splitter used from home depot tool rental for $1000.00 to replace a 30y/o that needed everything. It is actually way overbuilt for me but for the price its a bargin, theres plenty of others i see for sale at the rental places.

i fluid film my autos fluid film

By me all the refill companys do exchanges only, id rather do that, buying a new tank only to turn it in to the gas co and you get whatever they give you in exchange, you are also guaranteed that the tank you get is hydro tested certified so just get a couple of used cylinders off facebook...

or a bad injector stuck open

while the engine is running and engine cover off spray carb cleaner around the intake gaskets and se if you notice a change in rpm. they were known to leak.same with the carb to engine gasket

moog es2171r might do the trick cut end off end reweld

i did my the stabilizers on my backhoe. watched a few youtube vids and was confident enough to give it a go. Its super simple, i did buy the seal bending tool kit off ebay, it did make installing the inner seals super simple. hardest part was betting the piston nut off, on super tight. also get...

😀 $1000 is a joke, find somethimg else that will work like a tranny cooler

i use rustoleum on my truck body and trailer frame, I thin it with acetone and use hvlp sprayer, best paint for your money and stay away from latex paints

i have 6 mowers with pto clutchs and have never had to replace one, oldest one has 5500 hrs i would only stick to oem parts and that pulley is toasted, i have adjusted the air gap once on that 5500 hr scag most clutches have ajustable air gaps when they wear some are sealed on older toro z...

it wont harm anything to add the anti gel but its not needed. If its in a heated garage and has no problems starting and getting up to temp, then the fuel being returned to the tank is being heated by the cylinder head as its being returned.

Mine is still working the way it should so i never followed up on it but always thought i would use old school springs and small turnbuckles if mine stopped working some trial and error to keep it from creeping.

my gas inverter gen 2000w will run for 10hrs on 1 gal of gas, i use it at night time to power a light,fridges and gas heat ala you let the gas run dry at end of use it has always started for me after 8 years. have 3 of them at different houses.they are very quiet.

just curious as to how that happened

i asked about that when my skid steer trailer was being built, it all has to deal with proper tongue weight so you dont get the trailer fish tailing going down the highway. there are many youtube vids of that happening

Get them both

Last 2 digits of serial number is the year it was made

I use the orange spray bottles from home depot

It's control lessens over time. It doesn't last as long as it promises but it does buy u a lot of time.

https://www.zoro.com/astro-pneumatic-tool-co-undercoating-gun-economy-air-ao4538/i/G102671891/?gclid=CjwKCAiA0cyfBhBREiwAAtStHPXfFBT9kV4PLK4jWkx32pEYAY4DUGV0S-99Kq8j6bFEFVXE5WzacRoCT44QAvD_BwE&gclsrc=aw.ds using this for 3 years now with fluid film, sometimes have to warm up the fluid film to...

If you do use the lovejoy setup get Xtra spiders. They tend to fall apart at the worst times.

U could also cut the current bad splined section off and weld a new 13 spline section on. Or have a hydraulics shop do it. Once you remove the current coupler off. Try heating it

The engine has 1" shaft the pump is 7/8. If you can separate the current worn out one maybe you can use a lovejoy coupler with spider

Checkout hep02a

T looks like the additive package has separated out I've had that happen to me before with 5gall buckets of delvac that sat for a long time b4 I used it.

I idle my skidsteer and tlb for many hours and the thermostat cycles like it's supposed to.

The left side of the loose chain

I have a scag tiger cat with original clutch and prob ar o under 5000hrs. I have adjusted the air gap once. Sometimes the pto switch goes bad. Look to see if yours is an adjustable clutch but it shouldn't need adjustment with such low hours.

Weld a nut on to it

Your prob not going to get it out in one piece so I would order new ones instead of trying to reuse them. There's plenty of u tube vids on removing bearings. Those bearings are like one thousandth of an inch larger then the bore they sit in and are kept cold before installing.

Change all your pulleys

Checkout liftmatic self centering dampers

I went from an 8x12 to an 8.5x14 like it much better but eats tires much faster

Happens to me with the forks on my skidsteer

Google it. The walker mower is an awesome machine but the placement of the motor is detrimental to its longevity. The air intake sucks in so much debris inherent in the walker design with its suction blower it can't help itself from self destruction. I do have a few friends that have replaced...

Those walker engines get dusted a known issue with them.usually they just get replaced. Not worth the time effort or expense to repair them when it happens

Added new bushings to my friends skid steer a few years ago. Pretty simple if u can weld

I bought one of those Chinese junky ones that cuts 3/8. Please save your money and buy a name brand quality unit.

Buy a fuel tank grommet and brass push in fitting

I had to hammer drum brakes on a customer's Honda civic and it was only parked over the weekend.

Osgr means offset gear reduction. They are super easy to rebuild

If it's an osgr starter sometimes the solenoid contacts or the plunger are to blame.

Bought mine on ebay 4 yrs ago. It best viewed for me on the drivers side. I havent used it in a while. No real need. I justvwanted to know the highest rpm it would go and it was 3k just like the manual said so it was accurate enough for me. There are alternator based tachs also. The pickup is...

I used the tape and laser meter on my 535tlb works fine think I paid $10 put the tape on the crank pully 4 yrs later its still there

Try avm directly or allmand tractor parts

Ive had that happen on my scag.

Might need to adjust the clutch air gap

No corrosion protection with just water. Does that engine have cylinder liners

You can almost buy a new gas engine for just the cost of an injection pump on the diesel.

Ive seen them selling as high as 20k but sat. For a long time. If i try to sell mine i would want to walk away with 12k min. Mine works 100% with no issues. I wanted a mini ex also but its so nice only having to bring 1 machine to a small job. I can plant trees and move soil wirh the hoe.

I got mine pretty much the same way. The thick plate that the backhoe swing cylinders attach to was broken. I paid $8000 for my 535. Made it back the first yr I owned it.

Thank you.

Congrats. Who makes tge pump and the parts number please

The echos usually have a high speed adjustment only. It's a small hole with a white or black plastic plug covering it and u use a 2mm flat screwdriver to turn it after u remove the plug. It's hit or miss with the aftermarket carbs. Sometimes they are better then the factory ones.

Alfaggoma is that the Italian co who makes the gear pump

I just paid $4600 for a scag 36” walkbehind gear drive 😂

That sux. Its the small pump on the back of the eaton 72400 right.

Sorry to hear that hope you get it working again.

Thank you

Please post the part number for the seal kit. I might do mine

When u pull that out is there any check balls or springs that come out with it.

Keep me posted please

check that the relief valve isnt stuck. I dont know how to do that but it is one of the troubleshooting steps in the operaters manual

Theres mesh screens that at the tank bottom that might have debris

Cant really get in there for better shots

It was frozen solid today ill try tmrw

I'll check my 535 tomrw I think it's an Eaton 72400

I think they just put diff. Temp guages in. There is a site call allmandtractorparts.com they might have the original gauges. Theres a hst temp guage and a water temp guage. Afaik only my temp guage works.

The deckovers loading height is a real problem if you plan on using it for a skidsteer.

I have 2 gennys, i hate to waste resources so i operate them load dependently one is a 5500 watt gas honda the other is a 1600 watt inverter chinese made throwaway that runs great. the inverter genny will run 8-10 hrs on 1 gal. just a few lights and power the fridge all day/night long, i rarely...

Ever think the starter is weak

I like keeping factory oem crap the way it is also but if the factory gives u free KY jelly for $6000. Then have at it. Like the $20 relay and diode option

Joke all you want. It works. For $5.00 test it out u will see. There's plenty of info to back it up just Google it.

The baking soda makes the super glue form a super hard resin. I've repaired many plastic parts with it. I've read it has been used to repair helicopter blades.

Sandpaper and clean the area in need of repair. Apply super glue and quickly sprinkle baking soda into it.

Super glue and baking soda

It's a round plastic vacuum operated rubber diaphragm

The fuel pump only pumps fuel when the engine is cranking and or running. The fuel filter never fills up. To get it started after sitting so long pull the feed line to the filter and pre fill it.

Try shock bushings or track bar bushings

It's a def. No

There is a reason I've never ever seen those hooks with the pins being used. They are practically impractical. You could hook everything up correctly but still have everything move on you

Those hooks are nice for initial setup of the chains being bound but once you start tightening the binders you should release the pins. If you are worried about the hooks falling off during transit then you haven't attached them properly.

My scag tiger cat has recently started to eat them once a month. Can change it out in 10min. Now I had a toro z master a long time ago that would go thru them every 2 months but it took a long time to change that one. Had to remove clutch brackets on it. Got rid of it

I usually get around 3000 hours before they are bald. Always get 4ply

I have 3 new honda engines. The fist thing that gets done to them is new old style tank caps. Zero problems

If you can find older cap from older engines they fit and avoid this problem

When u have a run away engine Sounds like stuck open injectors.

Jumper wire BTW the 2 contacts.

Sometimes those cheap fuel pumps will run and fill the fuel filter then stop pumping enough. My tlb with yanmar 3tnv84 did the same thing till I changed the fuel pump

I have turf front tires and r1 rears. My tlb isn't 4wd a d I've never got stuck and they don't tear the grass up

I went through this a few years ago. Spent 3hrs oxygen acetylene torching my old ones off. With the large amount of material you Have I would weld some x156 teeth directly to those stumps and be done with it

Check motor to pump coupler

Buy a used one and sell it when your done.

https://www.amazon.com/Tool-Aid-25100-Short-Tester/dp/B000RFLR0U/ref=asc_df_B000RFLR0U/?tag=hyprod-20&linkCode=df0&hvadid=312177448019&hvpos=&hvnetw=g&hvrand=16042389085114942156&hvpone=&hvptwo=&hvqmt=&hvdev=t&hvdvcmdl=&hvlocint=&hvlocphy=1023022&hvtargid=pla-570889946543&psc=1&tag=&ref=&adgrpid=...

Checkout abom on youtube

😄😄😄

Yes. I called the warranty dept. They sent me a new plunger assembly. Problem solved till it happens again

You don't want a front or rear main leak so don't run it without fixing the issue

They are usually x156 teeth on smaller equipment like skid steers.

Those plunger safety switches stick shut

Safety switch. Those gray or black plunger switches

I've moved quite a few for landscape jobs. I put them on pallets and use stretch wrap. Use the skid steer to unload

I'd get a 14k lb. 2 5/16

Sounds like retarded timing

Tubes suk

The only ones I know of made in Italy are stucchi

Running on full choke indicates a blockage in the main jet

No drain it's a square plastic tank

Thank for the update

If you replace the lines like to use marine fuel line. Its thicker. Has a heat resistant outer jacket

Lock and stitch method might help Cast Iron Repair Engine Applications - Turlock, CA - LOCK-N-STITCH Inc.

Why do you even need one

i have a 10 year old fx691v with 4500hrs still runs great, a little smoke on startup. You are supposed to pull heads decarbon and lap valves every so often, i never have.

https://www.tractorbynet.com/forums/threads/bobcat-b200-hydrostatic-pump.169120/

it gets air locked because the rubber plunger head gets stuck in the tube. have had it happen to all my guns even the dewalt cordless gun, they sent me a new plunger. If the grease sits in there too long it seperates and hardens.

it kinda boils down to what type of injection system you have, and what type of emissions system.

when my father died 10 years ago he had a huge stockpile of cases of oil. i am still using it up, i just shake the jug up before i open them.

does anyone know the lift capacity of the backhoe at the bucket at full boom out. need to lift a 440 boat engine out of a boat. Thanx

I bought the machine used and instead of replacing worn teeth the other owner added newer ones, so, on an 18" bucket there were 7 mangled teeth almost like having a solid edge. I torched everything off and installed the x156 teeth. Ive purchased many broken generators, fixed and resold them...

I recently purchased a mini tlb an allmand 535. It has an 18" bucket on the backhoe. I need to change out the adapters and teeth, I removed what was there and now only have the bare cutting edge. I purchased cat j200 series theeth and adapters. I was wondering if they are too large for my...

I recently purchased a mini tlb an allmand 535. It has an 18" bucket on the backhoe. I need to change out the adapters and teeth, I removed what was there and now only have the bare cutting edge. I purchased cat j200 series theeth and adapters. I was wondering if they are too large for my...