Search results

My bad, your first response was right, my man found another Bobcat 331 and traced hoses and found I had two crossed. I feel like an idiot, but an idiot with a working Bobcat. thanks for all your help!

waiting couple days for my man to contact Bobcat to try to find out where power is coming from

the guy came over today and said pretty much the same thing. there is actually 5 solenoids on manifold at least one isn't getting power. He's not sure where it's getting power from, nothing in fuse panel refers to solenoids and all fuses good and relays good. He's going to find where they get...

that's same thing mechanic told me to check. He says all of these solenoid's should be energized when key is turned on, and to check with screwdriver to see if its nagnetized. But many years ago my high speed travel worked some time, I didn't know much about it. The switch that kicks into high...

when I loosened P3, my wife was watching and couldn't see the bottom of hose to see if it leaked so late yesterday I disconnected P3 completely and cranked over engine and it pissed like a big dog, so I was mistaken about flow. I have a retired mechanic coming Sunday. I will keep you informed...

didn't replace any joystick hoses,but heres food for thought. here is my pump, outlet one- I have right hand travel, boom works, pump outlet two- I have left hand travel, arm and bucket work, pump outlet three no swing or blade. then it says pump outlet two and three are combined for auxilary...

let me know if you get this and if it helps

I'm an old man, ain't very computer savy but here goes

I don't know if I know how to send schematic but I'll do some research on that. I took off hose on manifold end from port that supplies oil to functions I'm missing and no oil coming out isn't that telling me pump isn't pumping?

first thanks for any help. I know very little of Hydraulics but I'm a ok mechanic. I have parts manual and service manual, it is a two pump system, a gear pump and a piston pump. the port on pump controlling swing, blade and boost valve is on gear pump. I have no test equipment to test flow...

I did one at a time, took it off went to town got it put it on, then found another possible leaker, same with third. I'm wondering if I over heated pump, it bus bucking and barely moving for maybe 10-15 feet

lots went on road, oil dry cleaned up pretty good and I own land it's sitting on. some on neighbor's sand gravel drive he's ok with that

I was working my Bobcat 331D excavator for a neighbor. When finished I had to back down a gravel drive about 60-70 feet cross the road to my property. when I got to center of road I discovered I blew a hose, lots of oil on road. I had to get off road barely made it. After removing belly pan I...

makes sense, thats probable what happened. thanks for info!

added fluid when installed but obviously not enough, added more and working better thanks much

cycled about 30 times over two or three days. Don't understand why there's pressure in cylinder after engine off

my log splitter worked fine except cylinder was leaking a little,and I hate leaks, so I took cylinder in and they built me a new one. all I did was remove the two lines and put two lines on new cylinder.when I tried it out and extended the ram it extended but shakey, I figured there was air in...

mine did same thing replaced ignition switch problem solved

my 331D had no hydraulics at all,no blade nothing. pulled pump, gear fine. turned out to be magnet sensor in left console. I think part # is 6675665. I think it was about 50-60 bucks. if I remember right the sensor cracked and you could visibly see it after looking closely good luck

front electric clutch went out can't find one and shaft that clutch rides on bearing journals are worn. Clutch part # is 1685118-0 don't know what to do. tractor runs and looks fine but can't use mower deck any help?

my 331 bobcat lost all hydraulics. I've checked pump connector, fuses and now I'm looking for the solenoid that is operated by the console safety switch. It is so tight by the solenoids it's hard to unplug and check, but if I know which one exactly I will work at it I'm a new member and need...