Search results

Surplus Center uses USA hose (NPR Jones), but the connectors are Asian. I've had good luck with their premade hoses as long as you can live with the lengths* and the choice of NPT or JIC connections. * Lengths typically to the nearest 6".

Aside from the size (horsepower rating), they are both updraft carbs. The first one looks like the old Zenith carbs with a remote air cleaner. The second one looks like the air cleaner sits on top. Perhaps an oil bath type. The choke orientation is different on each--One on the engine side...

Is there a neutral safety switch. That generally kills all power. On my Ford, it's on the H-N-L Range Selector.

Have you checked the hydraulic oil level? Has it ever been changed? Filter change? The pump may have eaten the big one.

M16x1.5x90 10.9 is pretty common. What's "special" about it and the nut? Have a photo? Here's an equivalent SAE size.

You need full and safe support to work on any mower. When I work on my flail mower, I have it attached to the tractor 3PH, raised to full height and have jack stands under the side panels. Tractor in 1st gear low range with parking brake set on both sides. (Brake pedals locked together--Hiway...

The listing shows a carriage door entry in the back that appears to be the under-house garage. I don't see a way to get to it though. The "lawn" is too steep to drive down to it. And there's a big tree in front of it. You could probably use it to keep lawnmowers in it. As long as you don't run...

If you can't get a vented cap, make your own. Cut a round piece of plastic to fit tight to the underside on that seal area. Then put your holes in.

I hope you're never lost in the woods. My compas has 360 degrees. If North is 0 then 180 is South. :cool:

That should work but don't just drill it straight through. Drill one hole on an edge of the underside then drill the top hole 180 degrees from that. A straight through hole might gush gasoline.

Yeah, looks like the poor guy had to put his $5.5M lakefront property on the market a couple of years ago. That will buy a lot of liquor. I wonder if he still has his 50-foot Marquis sports yacht.

To a company, that stuff has already been paid for, depreciated and charged off at a considerable gain to the company for tax relief. Selling it, in any manner, would subject the company to a host of accounting, legal and tax problems. It's not worth it so it goes into a bin.

Here in America, we already do. They're called Wix Filters. ;) I just hate the M+H heavy claim of saving the planet.

My Kenbota had a Dynamo with a regulator. I canned all that and went with a 1986 Subaru alternator. It's not much bigger than the dynamo but has about 4-times the output. Just what I needed to run my extra lights.

I had a 71 Mustang in the early 70s. I was in the outside lane of a 4-lane divided road (not a highway) going into a sharp right turn. It was near downtown and the speed limit was 25. The guy ahead of me about three car lengths was in the left lane. Wet road conditions after heavy rain. The guy...

Mom went to be with the Lord last Wednesday and joined my dad and oldest brother. She went in her sleep without pain or trauma. The healthcare worker tried her best to revive her but to no avail. She was 98 and had a pretty good run. She was the oldest of her siblings and only the youngest...

It sounds like you've already made up your mind. My 64" flail will load my 50hp on high weeds, so I generally use it as a finish mower. It has the spoon blades and does a fine job at leaving a finished look. Rough to look at now but I have a welder, paint and new decals for it. ;)

Nondetergent oil is/was made for machines that don't have an oil filter. Particles and carbon would sink to the bottom of the pan and be drained out with the next change. Switching to a detergent oil will keep the junk in suspension and most likely cause a faster wear rate. It can also loosen...

It sure would give Matt's Off-Road Recovery more business. 🤣

I have plenty of 1/2" sockets. I also have the 3/4 and 1" sockets to cover some large nut/bolt sizes on some equipment. I use adapters on my 1/2" impact. The sizes go up and down, but it would scare me to use a 1/4" socket with a 1/2" impact. :oops:

That's because they have larger anvils and produce higher torque. Beats the $900+ Mularkey. Besides, I already had the batteries. Hands down, better there too. ;) I'm not wrapping gifts with it. Vibration is secondary.

I'm pretty sure I'd need help holding that thing. My aged grip and wrists have trouble with my 1/2" DeWalt. It only comes out on special occasions now. Bought another 1/4" hex driver in the stubby format. That thing rocks! Three speed variable too. :cool: Anyway, I like talking tools. 🤣

The days of COD are long gone. Where have you been? Typically, a seller will run a $1 hold on a CC. That's to make sure the card is valid. I don't think they can charge the full amount to your card until it's shipped. At least that's how it's been working for my shipped purchases. Even Amazon...

Yeah, but it's green. :sick: 🤣

And.... They have a computer and sensors that MUST remain dry. ;) Use caution when cleaning or washing. Corrosion is the biggest enemy.

I agree with your posts but perhaps you are expecting more out of your machine than it's designed to deliver. 🫣

High winds coming back today. Supposed to get 3-5 inches of rain then drop into the low teens again. I'll probably park my truck under a tree to protect it from the hail that might come with the rain.

Americans are too stupid to deal with that kind of voltage. We still have 2-prong plugs everywhere. "In the United States, there are approximately 1000 deaths per year, as a result of electrical injuries. Of these, approximately 400 are due to high-voltage electrical injuries, and lightning...

My tractor is 38 years old and still running strong. I'm pretty sure you won't see any electric tractors that old even with a restoration. The batteries will just be too costly. And it's not like anyone will be able to restore the batteries at home. You won't be able to buy a battery pack from...

I lost the eucalyptus tree I planted back around 2005 last year. It was a fast grower. It was everything you say but I still miss the fragrance of it. Thought about planting more with better access to water.

I'll be 100 years old in 2050 so I don't think it will be a concern of mine unless I'm still driving. :cool: One thing for sure, I won't be driving an EV unless it was given to me. By then, an EV will most likely cost about $300,000 for the budget line.

Warmed up a little but still chilly for me. Supposed to hit 70 today so I'll be outside cleaning up the high wind mess around here and charging batteries. Looks like T-Shirt weather today but we're in for another drop this weekend. Stay warm and Hydrate! (y)

Spoke too soon. Electric went out this morning. Just came back on about half an hour ago. Quickly made coffee and enjoying "the crispness" of the morning. Not much change from yesterday--Still under a hard freeze warning. Heater is just catching up as I type this. I'm on coffee break. ☃️

Bitter cold here but at least the electric is staying on. And there's no snow. I had to shovel dust from in front of the barn man door to get in yesterday though. Pollen count is way up.

All find and dandy, but all this thread did is remind me I've got to work on the 1956 JD-420C this year. 🥹 It needs steering clutches and some undercarriage work. It runs great, but only makes left turns. Getting it back to the barn was a chore after a long day on the driveway. Had to stop and...

Once you plug any leaking and the area is dry, you can build back rubber with windshield urethane if a pit bothers you. The urethane comes in a caulking style canister. Once you open it, make use of it because you can store it after that. I've repaired lawn tractor tires with it (as well as...

Everything is dried up by August down here. :cry:

I don't think you can say "White Christmas" or "White New Year" anymore. Some might say it's racially motivated. :rolleyes: Winter came early down here. We hit a brutally cold 45 around the first part of December. It's now 37 and my heater is blasting! Looks like I'm staying in today. I might...

It's still early. :LOL:

I lived in Ohio during that period. Always seem to be a heartbreak. I quit following the Browns when they moved to Baltimore in the middle of the night. :rolleyes: Edit: Just as well. That was the same year I moved back to Texas--1995. :love:

My experience with battery tenders would be to NEVER turn them off unless you remove them from the battery. If you lose/cut power to them they will render a battery stone-cold dead in about a week. This is the type that tell you to connect the battery first then plug the tender into AC. Without...

I've been using a 30-gallon barrel. I bought it new, so it came with the plugs. I thought about a 50 but this is easier for me to move around on a dolly. I use a 12v battery powered pump and it's set up on the dolly. When it's empty, I strap it down in the truck and take it to the gas/diesel...

TPU (Thermoplastic Polyurethane) filament is flexible. It's generally available from 75-95 Shore A and some special types of TPU filaments with Shore hardness down to 40A. I just made an O-ring seal a couple of days ago with it.

After Sunday's game, I'm pretty sure the Cowboys won't be there. They got everybody rooting but dropped two games in a row. The play calling was terrible. That's not how they play at home games. The best they can do now is a wild card spot. I doubt they'll make it out of the first round. :rolleyes:

I would be sure to use hose clamps. Nothing more expensive than traveling down the road while leaving a trail of flames.

Merry Christmas to all!!! This would have been an even better day if Microsoft hadn't meddled with/in my PC. It's what, nearly 5pm, and I just regained control of it. It all started when I tried to do a Backup this morning. What a bunch of BS they put me through and it's not even their PC. 🥹

Do you have a picture of one? Dorman sells off the shelf boots for $6-$8 and found at most auto parts stores. Google "tie rod boots" and see if you can find one close. They come in many forms. Or find someone that can make a 3D file and print it out of TPU filament. I've got the printer and...

I have the same one I bought a year ago in November. Works great, still great. I had to partially assemble mine down front (delivered next to driveway) since I couldn't lift it with my Kenbota with forks. I had to hook it up to the Ford 3PH to get it to the barn. Everything was there but nuts...

Speaking of Hellcats; I see that many can outrun the Arkansas Highway Patrol cars--150mph+. Not all, but many. :LOL:

Thanks for clearing that up. 🫣

Small gas engines that sit a long time will most always have a clogged emulsion tube and high-speed jet in the carburetor. The only way to clean them is to remove the carburetor, disassemble it and clean. The reason is alcohol in the gas. It absorbs water and corrodes the brass and aluminum...

That only works on concrete. I use lacquer thinner. It's cheaper and works better. But, like I said, only on concrete. Pour it on, let sit for a minute then soak it up with paper towels. This method has always worked for me. That oil will bleed through any top coating unless you first seal it...

The price for regular gas here was $1.899 a gallon before the current administration. :rolleyes:

Well, if you guys run short of gophers, I can send you some. :LOL:

Yes, I have my address on a post next to my driveway. They're visible from both directions. I also have a back lighted number sign at the top. At least it used to be lighted. Solar panels don't do well in South Texas. But the numbers are still visible from the road during the day. And that post...

FedEx is the worst around here, but they seem to be improving. FedEx used to just throw the package over the fence next to my driveway. My driveway is off a state highway with high traffic. They once delivered an Express Envelope to the hillbillies across the highway. I had to call the Sheriff...

I never had a problem starting my Polan gas chainsaw until arthritis made it impossible to pull the starter rope. That's when I switched to electric. I'm not a logger. The 12" DeWalt does everything I need and most of the wood around here is Mesquite--One of the hardest woods known to man.

Yep, the VIOFO has it all. I just didn't list them. And the picture quality is unmatched within the price range. That's why I upgraded from the 119 to the 129 Duo. Dashcam Viewer has a huge list of compatible cameras/systems. You can view the videos with a lot of software including Windows Media...

Chilly and dry here if you consider 50% humidity dry. After all the light rain we've had, that's pretty dry. :unsure: Went out yesterday morning to grab a few things at the store and found a dead battery in the truck. Went back into the house and ordered a battery charger on Amazon. It was...

I have not had a problem with mine. The problem I see most is caused by poor/faulty installation. Can't help you or her with that. To retrieve the videos, you can also just remove the XD card. Put it in an adapter and view the video on a PC. There will be two videos (front and rear view) every...

Well, there's your problem. :cool:

That's why I invested in a VIOFO A129 Duo dash cam. A press of button on my dash will save and lock the current recorded files (front and rear). At least I can try and get a license plate or vehicle description. It can also aid your defense in fault questions. You can download the videos to your...

I was pretty deep into CB radios back in the 70s to early 90s. I traveled by car or camper a lot back then. My handle was "Captain Computer". I had a license but let it lapse as well. After I realized no one else was getting a license. I still have my tweaked base station. Talked to the World...

Reminds me of my first day in Cleveland, Ohio in 1976. Moved to Euclid, Ohio from San Antonio, Texas. Driving into work down Euclid Avenue was about the same as driving on Military Hiway. Folks were just a little darker. I was never treated bad. Perhaps it's the way you present yourself.

It doesn't say so but there's some very thick fog here right now. I did report it. I need to mow some grass but with the fog and humidity, it will be too wet. All summer it's been hot and dry. My last mow was back in February, I think. Could be another wet and cold winter this year. I'll be...

I have a leak detector in the tray under my water heater. However, I don't recall the last time I changed the batteries. :rolleyes:

You have to include the battery as factory power so I'd say ZERO will still be around in 40 years.

Probably separate motor for the PTO. And what's the joystick for? :oops:

Probably just Chinese rubber. Even the good blades only last a year down here in the heat. When I have the annual inspection done on the truck, I have them put new wiper blades on. Then I'm good for another year. :rolleyes:

If this is a real log cabin, I would use fasteners that went all the way to the logs. I watched the builders of my house in Ohio over a period of several months. My fireplace was brick from hearth to ceiling. They poured a concrete footer and had block support in the basement for mine. During...

A little dreary with fog this morning. But it still might make 78 today. I slept in and feel good about it. :LOL:

They have hills like that in NYC? :oops:

I don't know what my 2006 GMC 4x4 gets and don't care. I drive less than 5k miles a year and get a good discount on insurance. When I do buy gas, I get the premium. A full tank will last me over a month of trips to doctor appointments, grocery shopping and a trip to Tractor Supply now and then...

Nice going, but I don't do FB or any of the others.

Nice day today but the Cedar pollen is affecting South Texas. It comes down here from the Hill Country NW of the big city about this time of the year. Gotta try and get some chores done.

It's not worth messing with those things. If I have a fitting that won't take grease with my lock-on nozzle and electric grease gun, it gets 1-2 whacks with my unclogger. (A pen shaped tool with grease in front of a piston.) If that doesn't work, I replace the fitting. I got a box of like 100 in...

Is that all the info you're going to give? :unsure:

I'll follow along because I used to raise grapes and strawberries about 15 years ago. Shared more with the birds than I got to eat or sell. Had a 100-year freeze that wiped out everything here in South Texas. I don't do wine, so I never got back into it. That's good because we had another record...

I'd like a nice pair of adjustable aids. I tried the cheap amplifiers, and they sounded like the old tin-can and string communicators. Real tinny and couldn't adjust them except for sound level. There are better ones, but I hate the behind the ear versions. They look like deer hooves, and I...

Yes. The Allen screw keeps pressure against the two pins on the valve in the two channels in the knob. It shouldn't take much torque to keep the knob tight on the valve. Too much torque will break the channels off the knob. It's still a great design. I have some 1" aluminum round stock and the...

I guess I should have re-read the Amazon listing. :cry: It slides on over the release screw, turns 1/4 turn then secured in place with a set screw (included) from the end of the knob. You will need to use a 5/32 hex key (Allen wrench)

I was going to use a spring in the hole to keep it tight. It might already come with one, I don't know.

I just edited the post. (y)

I saw the all metal one on Amazon and was going to order one. Then figured I could make a couple of those for the shop. As yet, I haven't and the last time I looked, they were sold out on Amazon. :cry: Hey, they're back in stock.

I would have bought that back from the insurance company and do a body swap. That 355hp in a 4,000-pound car would have been fun to drive. (y) :LOL:

I don't know anything about the Dyna Lifts but perhaps the pump is still bad. :( The first question is how much pressure is it providing the system? In other words, did you do a pressure test? The "squirt test" is not only unreliable but also considerably dangerous--As in fatal or amputation...

It sure has changed for me. I used to build my own PCs. The latest and fastest processor, maximum ram, top tear video board and the best motherboard. All mounted in a full-size tower with a TV tuner front display. I spent thousands of dollars on those machines. Now my PC mounts on the back of...

Ha, ha, ha. My bank just started sending me dormant notices on a savings account. I pulled out money just before they paid some measly interest. I guess I should transfer it to a checking account before the state gets it. I'm 73. I have some set aside for an emergency, but I just decided to...

It could be that Branson is not SSQA compatible or not to spec. I have Titan forks in SSQA and they fit as well as a home-built bucket with a SSQA back panel. Here's the specs for the attachment panel.

Mostly cloudy with a chance of rain before lunch. It's 56 degrees and probably won't change for the rest of the day. I need to do a little grocery shopping, so I'll try to get out before the rains come. Otherwise, a slow day. Waiting on another AMS for the 3D printer and it's too humid to melt...

In my opinion, 1986 was the last good year for Ford tractors. They went downhill from there then New Holland tried. NH should have stayed making implements. They were good at that. I plan to be buried with my Ford 3910 which is a 1986 in pristine condition. (Restored from the picture in my avatar.)

You'll probably find a bunch of broken plastic in there and the dealer wants $700 to fix it by putting new plastic in there. :rolleyes: On my old stuff, I just squirt a little oil in there and it's good as new. :LOL:

Why would you want a speedometer anyway? Do you do that much road travel? :rolleyes:

Ditto on sprockets and track pins. The other wear points are the lower rollers and upper idler. Also check the front auto-tension wheel bushings. That lift looks homemade but if it works, it works. If it came with a lift cylinder, perhaps it has the PTO also. (???) The PTO lever is on the...

If that's a picture of one, it looks like it would be easy to make one with parts available from Tractor Supply.

I have a county road on my eastern side that tees into a state road on my southern side. That stop sign is a popular spot for dumping beer cans, bottles, fast food trash and even garbage. Every time I mowed the corner, I'd fill a big black trash bag. I quit mowing the corner a few years ago...

Sure, but what's the fun in that? If there's much left, it will come out in liquid form.

I have the Amazon version of those. The 3/8" refers to the size of the chain, not the bolts. The bolts that came with mine are 1/2". Mine would probably pull through the bucket material before failing. They will also outwork the lift on my Kenbota. :rolleyes:

Brass doesn't spark but the valve may contain a steel pin in the mechanics of the valve. That would (could) spark. I'd enjoy the 308 method of emptying. Take note, gas can remain in the tank even when it appears to be empty. Propane is heavier than air.

74 going to 87 with a chance of light showers today. Sunday night, we're supposed to drop to around 45 getting no higher than 48 on Monday. That's unusually cold down here at this time of the year. We typically don't see that until late December. Must be Global Warming! :eek:

Welcome to the Forum! (y) I had to refresh my memory too. Hadn't heard land referred to that way since my grandad farmed. Are you from the "old county"? One hectare is equal to 100 square meters or about 2.47ac. So 18Ha. is just under 47.5ac. My grandfather made a living on 40ac. so there's a...

Are you talking about the steering column valve? Is it a Parker valve? If so, those have a specific order of assembly with the notches in a specific position. Change one plate and you're out of luck. I hope you took a picture of the original. Otherwise, you'll need the manufacture's overhaul...

The builder may have broken a ring putting them in. Were the cylinders honed? In that photo, they look like crap. Oil in the exhaust can only come from a poor ring job.

What's the problem with your cable? Did the end just pull off or did the cable break? I'd be making my own before paying $750 for an assembly. You can buy cable stock and a handy farmer can make threaded ends from a grade-8 bolt.

Yes, it is. The photo after it (original post) shows the inside.

That photo of the Angata Camp reminded me of the John Wayne movie Hatari. :LOL:

My dad owned (leased) a gas station in 1967-70. I worked there during my junior and senior years in high school (1967-68). Gas was generally 19-20 cents a gallon and dropped to 17 cents during "gas wars". The price was set by the supplier most of the time. Starting around 1969-70 I saw gas move...

No, it is not normal to have misaligned pulleys. Something may be bent, or a bearing is worn allowing a pulley to shift on its axis. It's also extremely important to keep the correct tension on belts.

I see a what looks like a 39 Ford on the right side of that picture. It also looks like it's in the South. That price was good until about the late 60s when the then administration again locked down the oil and there was NO gas. Remember the gas lines of the 70s?

You know that's not going to happen with the current administration. He has already said, "No more oil". We'll have to go to war before he breaks that promise. Or folks are so poor, hungry and out of work because our life depends on China.

My mom will be 98 in January. I'm hoping she makes it. It's been a little rough on her lately with bad knees. Her aunt lived to 105 with the same ailment. Lost my dad in 2010 but he had a good run to 86.

73 going to 89 today with a 56% chance of rain. Added another candle to the cake today. Life is still good. (y)

My first guess would be a rusted-out muffler. The iron oxide that forms as well as the carbon can ignite and throw sparks. As already mentioned, running a test at night with a hot engine should show if there's any sparks generated. Fires don't start on their own.

It's one and same down here. Hay when it's new, straw when it's dried out. Not many green "lawns" down here this year. No rain and record heat all summer. Just set another record high yesterday. 97 F-ing degrees (as opposed to C degrees)! I only mowed once this year. I think it was back in...

Just like plowing, the tires that drop into the fresh cut ground on the next pass will tilt the tractor. Being capable of leveling the tiller when this happens keeps the cut/depth equal and covers the tracts. I'm sorry you've never used or understood TnT. :cry:

Same here. But I guess it depends on the quality of the straw. I ended up with a yard full of "weeds". It took a while to eliminate the weeds.

That's the beauty of having TnT hydraulics on the 3Ph. It doesn't matter how wide the tiller is--You can offset each pass to fully cover tractor tracks. The TnT allows you to raise (or drop) one side to compensate for "sink". It doesn't matter whether you're going up one side and down the other...

MUTF is what it calls for. Couldn't find any specs on it to be more precise. Best to use what's already in it and not mix oils.

This is my old Case drag. I'd say you're missing a lot of yours.

It looks like it must have a rotating sleeve that unscrews then the connector is pulled off--Similar to the old speedometer connections. I don't own a Mahindra so I could be dead wrong but, I just looked at the sensor. (shown below)

Starting on the date of the purchase, I'd be wanting the per day rental amount since it was now my tractor.

Thats how my 3910 is plumbed. But the thermostart element is also a valve. It opens when heated. There's also a separate point on the ignition switch too. It's just before the Start so you have to release the start and turn it back one position. I've wired the air cleaner light to also indicate...

That's a mighty fine-looking tank. (y) I would make sure it doesn't vibrate or it may not last 9 months.

All my flat face couplers have a notch on the release ring. Is that what you're talking about? It needs to line up with the pin/ball to release the coupler. The release ring will rotate so you can lock a coupler together if necessary.

Good luck! Many of those steering column units are not repairable. When they leak, you have to replace the whole unit and typically in the $1500 range. :oops:

Those were the original "quick connect" fittings. The lube kit I got for my electric grease gun has a lock-on attachment similar to that but for standard grease fittings. It slides on and locks onto the fitting from the side. Its handy for hard-to-reach fittings or fittings where you can't get a...

The image shown by BCP is looking down from above the plow.

You beat me to it. I've seen that rub but couldn't figure out what it was made of. It's treated with something but didn't catch that either. It seems to work, and the cattle don't seem to mind. They just stroll under it when he moves them from pasture to pasture.

I'd buy one of those tomorrow for that price if I could find one close.

This is what Tractor Data has to say. (3000lb. lift to full height.)

Yeah, but it my money. I don't like others spending it for me. The water company knew there was a main at the front of the property. Their job was to get it to the property line with a meter and valve. They would have had to put the meter at the top of an 8-foot bank of the county road. It made...

Nice place! (y) I remember my building days back in Ohio. The wife and I were there every day after work and on days off. It was an exciting time filled with good and bad memories. We had a 40-pound chandler going in the dining room. The electrician had a e-box mounted on piece a of tin...

Big money is right. When I put city water in about 14 years ago, the water company wanted to put my meter on the other side of an adjoining county road. They wanted $5k to drill under the road. I said put it off the main at the front of the property. The main was already on my side of the State...

It's apparent by that link that there may be a lot of dealers struggling to survive. Seems to be quite a bit of mergers and acquisitions going on. Yet prices keep going up. :rolleyes:

Being made by someone else may be a good thing. ;) If BB were making them, I would pass. BB doesn't know how to powder coat parts. I say this because every edge of every panel and part has shed its powder coat or is about to. Something went wrong on the edges--Its flaking off. My two-year-old...

You can order concrete with the color already in it. I think there's 20-30 colors available. As far as staining concrete, you have to seal it after staining. And the stain pretty much stays near the surface so chipping or heavy traffic will wear it off. They make special sealers too.

I wouldn't use oil, new or used. The smell would be around forever. I have a few spills on my barn floor from rebuilding an engine 10 years ago and I still smell it when I go in there. The only thing that smells better is the cutting oil I use for my mill and lathe. :oops:

I tried to sell my auction cache of mostly B&S parts (NIB) to a local dealer. He wanted an itemized list of part numbers. I said make one yourself and walked away. It would take me months to list individual part numbers. The volume equates to two long bed truck's worth of parts. I used a few...

Can't "float" an original top link either. Not sure what you're saying. :oops: I have a stirrup link on my top cylinder to the QH. It allows for float as does the 3PH. I typically use the top cylinder to make it easier to grab different implements with the QH and to adjust the cut of my back...

I see three broken teeth on the input gear. And the breaks look old. That's how it starts. A piece of hardened tooth will wipe out other teeth and bearings in short order. (You can see pieces in the bottom.) That's most likely what caused the seal to start leaking too when the bearing let the...

The old dry-cleaning fluid would get just about anything out--Grease, ink, glue, baby "stuff" and everything else. Not sure what they use now but I know it's not as strong. All the readily available strong solvents went away in the 80s. I still have about a case of some old AC system cleaner...

Hard to believe a broken leg is OK but at least you survived. That's a good thing. We pray for your quick recovery. :eek: Probably all you lost was a little diesel. Any oil that leaked into the valve cover and combustion chambers will leak back to the oil pan if it's been sitting up right for a...

Nope Cut and weld. You'll need the loader side with the levers and the bucket side.

It can't possibly be that tight. Use a 6-point socket and rachet. Are you sure you're trying to turn the right way. It is upside down you know.

Same here. Heard on the radio this morning that Central Texas lakes are in trouble. We had a little sprinkle a few weeks ago but dry as bone here. Everything is dying including the cactus. In really hard times, the ranchers down here will feed cleaned cactus to the cattle. Don't know what...

You need more information than the ISO number. You need the specs for the Mahindra oil before trying to match it to something else. I checked the fluids at TSC and none of them mentioned Mahindra in the specs. If you can't get the specs, you're better off getting the Mahindra oil from a dealer...

I didn't mean to sound like I was putting the machine down. I meant that type of valve is the cheaper of all the different types of steering valves. I robbed one off a Commercial Jacobs Reel Mower to use in my Kenbota. It's an open center valve so it needs its own source of pressure or a divider...

Sounds like a non-load orbital valve style steering. The non-load means there's no feedback felt in the steering wheel. This type also doesn't return to center if you let go of the steering wheel. There isn't a center. The valve sends the preasure in the direction you turn. Not the best but they...

I'm just glad I don't have to buy all that stuff again. :ROFLMAO:

Just a side note; Tesla is building a new Lithium production facility in Texas--On the Gulf Coast. Close to the water. I guess in case it goes up in flames. :LOL:

That's to keep them from burning down houses. :oops:

Still, never talk about a budget up front. Look at the tractor you need for what you want to get done. If it's 25hp then so be it. Let the dealer talk money. Do your research before you get there. 20% off for a 2023 would just start me thinking since they've already been marked up at least 10%...

Must be a common problem. Everybody sells replacement assemblies, including Amazon, but can't seem to find parts. Not even from a dealer. Good luck.

I don't know much about the Mitsubishi, but it sounds like the transmission may be low on oil. I think those might use a torque converter and oil is absolutely necessary for it to work. Not sure how your name got by the Moderators, but I'd see a doctor about it. o_O

Oh man. Never go to a dealer flashing your down payment and want for a specific monthly payment. You probably overpaid. It's the same as buying a car. Look for the product then discuss financials. Let them convince you with the deal--Not the other way around. Kioti is offering a lot of incentive...

Smelling diesel and not seeing smoke is a sure sign you may have a diesel leak. Depending on where it is, that would cause loss of power. Check your engine for obvious fuel leaks. Especially the injector lines and supply to the injector pump. Check the oil level. If it's over full, you may have...

I dated a girl from Oklahoma. That was spot on. :ROFLMAO:

It could be a number of things causing low power. In your case, I'd tool up to check compression. If you're smelling diesel or seeing white smoke from the exhaust when it's losing power, the injector pump/governor may be trying to feed more fuel. Were the valves adjusted during break-in? Are you...

Ok, but I was talking about the sewing machine. :LOL: My old Singer came with a twisted pair cord. Your recorder would be using wire instead of tape if it was as old as the sewing machine. ;)

Around here, charges are Tier based. The less you use, the more it costs. The more you use, the less it costs. I use what I have to. My house is all electric. I don't have much choice. They even charge for a meter whether you use electricity or not. It's like $9 a month for the meter I used for...

Except my browser is flashing a big red warning--"Not Secure" on that site. There are others. Even Amazon has it.

As Ryan the concrete guy would say, "Good Work"! (y)

I bet that cord was the old cloth covered twisted pair type cord. You can still buy that but it's not cheap. It's sold by the foot.

77 here going to 100+ with heat index approaching 107+. Overcast but they're saying no rain. It's so humid right now, it looks a little foggy out. I'll go out and affix the new registration sticker on the windshield but after that, I'm staying indoors with the AC.

I guess you don't have a tripod then. :cry:

Well great, where's the leak then? I'm hard of hearing. :cool:

I take it you didn't buy the kit with the locks. :( While you're buying everything piece by piece, throw in some braided hose cover too. The sun will eat up bare rubber hose and look scrappy and cracked after a year or two. ORB fittings use O-rings to seal. JIC fittings don't use anything--They...

Just what I want to see when diagnosing an engine noise--A video of the dash. o_O

I have 1/4" hoses on my TnT. They operate too fast for my liking. I plan on getting some restrictors to slow them down. :oops:

Those belts look worn out. :rolleyes: The original probably broke off. May be a new spring too. Most spring tensioners have an adjustment as well. Check a parts book for the spring setup and get the correct belts.

Well now you're just showing off. :ROFLMAO:

Good point but I just got through paying $77 for registration renewal on my truck that gets driven less than 5,000 miles a year. I certainly wouldn't want to pay more. I'm paying the (state and Fed) gas tax on top of that.

This being your second post in two years is not likely to carry much weight. I have 36" forks from Titan, and they lift the maximum my tractor will handle. They show no signs of the wear you note nor aged any more than my other attachments. I suspect you are a vendor from another company...

While we're on the subject; Texas just enacted a new law taxing EVs. They can no longer get away with using the roads for free while the rest of us pay the tax on gas. Effective September 1st: Electric Vehicle tax: Because electric vehicles do not pay tax on gas, SB 505 will require owners of...

Nice Work! Looks professional and neat. Great pictures too. (y)

No radio but I use noise canceling headphones that are Bluetooth linked to the phone in my pocket. I use the PI Music Player on my phone and listen to "oldies but goodies" I've been accumulating over the years. I've managed to acquire songs from the 50s on and have them grouped to play depending...

Yep, they don't stop on their own. I have the same engine in my Kenbota. It started life as a G3200 lawnmower with 1300+ hours. It's still running strong. The only thing I did was clean it, paint it and changed to a "real" alternator. It's no longer a lawnmower. ;)

Open the radiator cap and see if its drinking coolant. Could be a blown head gasket.

The question would be if your 8.2 gal/min implement pump is enough to run one. Couldn't find the specs on the drill.

I have one in my little town. They're worthless. They couldn't patch my tractor tube. It went flat the next day. I took the tube out and apparently, they just put a patch over the top of mine. I got a tubeless valve, juiced the tire with a little Slime and it's been holding air since.

So, you're looking to get one for free? You can have mine. I'm in Texas.

Yeah, cylinders are capable of bending and tearing metal to reach full stroke. Don't ask how I know that. I had to change some geometry when I was building the loader for the Kenbota. Make sure the cylinder(s) stop first. (And hopefully you have a release valve in your design.)

The idiots will make gasoline so expensive only the government and millionaires will be able to buy it. The rest of us peons will be forced to walk, ride a bicycle or pay for public transportation. :rolleyes:

Nodar is more accurate. I was tempted to buy a 3D printer that has Lidar on the print head. It's supposed to stop the printing if it recognizes spaghetti or detects a bad first layer. It should save a lot of wasted material. I'm still thinking about it, but I hate to spend that much unless I can...

I've done all that and more. Now I watch movies on TV while it's 104+ degrees outside. It was just after 7:30pm and it was still 98. It cooled down to 77 after that because a storm went by. So tomorrow looks like it will over 100 with high humidity. I'm checking tomorrows TV schedule now. :LOL:

Great work! I've been lazy since temps hitting 100+ daily set in since about June. We beat the longest streak over 100 set back in 2009. Doesn't look like we're getting a reprieve any time soon. :(

You should use a cleaner like CCleaner. It's free and allows you to clean unwanted cookies and hidden history from your PC. You can select which cookies to keep so you don't have to sign-in each visit to a favorite website. There's also a phone version. The Pro version even does more. (y)

I saw the same when I tried to order from them. I canceled out. I looked up the address for "Nova Tractors" and it's a residence just North of Houston. Apparently, he drop ships and doesn't actually have anything in stock. So, I wonder what his delivery schedule is like. I didn't see anything on...

If you are a cop, there are places in the brotherhood that have special terms for police officers. Check with your department. Code 7.

It was worth it to me for a back-blade. Also why I got locks on my cylinders. When set at a normal position, the hoses can be pulled from the couplers and the remote used on another implement. Perhaps like a side-shift flail mower. The locks take the pressure, not a disconnected hose. ;)

Thanks, but I have a reader and it's not the speed sensor. ;) I found some taped wires under the driver's seat so I'm sure someone else was chasing this too. I haven't had a chance to look deeper. A common problem with the GM vehicles is the front crash sensors. The bolt corrodes and splits...

I'm a cheapskate and don't like to wait months for something I paid for, so I made my own. I had to modify the lower connection since the cylinder wouldn't clear the rearend when down. I don't remember where I got the cylinders, but they came with the locks and hoses for less than a single...

Only if they're candied. :sick: I don't have one, but I'd be trying French fries. But I don't know what they're called in the UK. o_O Chips, maybe.

Could be a frozen cable from lack of maintenance. You should probably take your tractor to someone who knows how to work on them. Looks like someone already broke the cap getting that off. :cool:

Will those mount on the side of a trailer? My GMC came with a bed-mount box when I bought it. It didn't really fit well so I took it out. Besides, it took up too much space. o_O

The metal bracing looks too thick to be Countyline. :ROFLMAO: At least compared to the new ones. I have one of those. :rolleyes:

Congratulations! (y) The thought of buying a new or newer truck has been in my mind. Especially since I've been spending time on my GMC tracking down an air bag light. I'm certain the problem is wiring. It's like chasing a cat. The codes keep changing. It all started when I hit a pothole last...

Ever since I picked up a used Ford 782A Back Blade, it's been my go-to implement for maintaining my clay-dirt driveway. And having TnT makes it quick and easy. I can make it dig-in or float just by changing the angle of attack (3PH Top cylinder). I've been thinking about adding a cylinder to it...

For sure. Those bags seem to be made out of plastic. Some have a layer of fiberglass, but none guaranteed more than 2200F coverage. I did notice one would refund or replace the bag if it failed. Great, what if it didn't save my barn or house? :rolleyes:

I was just looking for a new Flowmaster, 2-in, 2-out to replace the old leaky one in the truck. Imagine my guffaw when I see them for going for about $200. :oops: I seem to remember "glass-packs" going for less than $20 when I was in High School.