Search results

Cool. I bought another set of tires & wheels. I'll have to try the Tireject. Thanks!

Just replaced one of the deck wheels tubes. Made it one mowing. All the tires that show up on a search have a 5/8" bore. Not sure if I can swap the oem wheels to the aftermarket to make it all work. Anyone have suggestions. They're not cheap.

Yes its been awhile.

Factory wight. I'll try to get a pic

I purchased a 2" receiver hitch from Harbor Freight for $25. Bolted right on my F3680 several years ago.

Waiting on metal.

Finally got started on this. Seems its trained for 3 days every week. That and my fire dept schedule havent helped. So bored 15" holes 3' deep and built 15" square forms. Used pea gravel aggregate in concrete. My trailer guy cut some 3"x5" angle for me. Did a mock up of roof so customer could...

I have to build a gazebo/judging stand at an equestrian facility. Very good customer. I was wanting to pour concrete piers and attach the base to the piers. Basically it would be a deck attached to the piers with a roof. The piers at the front will only be about 8" out of the ground and maybe...

I've used the residential and commercial versions on my buildings. Only way to go. And do a high lift door for extra clearance

Anyone know the part # for the remote hydraulic kit? And a price? Thanks Greg

Kids Trick or Treat outfits. My Trick or Treat outfit.

Anyone here dealt with it? I'm having surgery the 29th.

My Husqvarna 365 is 21 years old. Always been good till now. Cutting some trees for a customer when it ran out of fuel. Filled it went to finish and saw would only run wide open, if it tries to idle it dies. Have to choke to start and same thing. Tried different gas no change. Obviously it gets...

My wife brought this to the firestation yesterday for me. I think she dun good.

Nice trailer Gatorguy. AZTim Sweet setup! Ive thought of getting an F450 and going with super singles. Also been looking at Midsota Trailers for a couple years. Didn't kow you could get 10k axles with singles. I have a 20k gooseneck flat with duals and it beats me to death empty. It doesn't look...

Here's mine. 500 gallons and 2000gpm

Anyone have any long term experience with it? I built a deck for a customer about 7 years ago and the 5/4 deck boards are deteriorating. I have another customer with a deck that has Trex on it and looks like crap. I can get Ipe' out of Atlanta for about the same price as Trex but I have no prior...

Stopped by the Deere dealership to see what they offer. They can get a Danuser with tilt for $8200. I'm tired of boring and packing posts.

Well we're adding 20'. Now if the rain would stay away.

She got her ceiling fans and decorations up so I think its complete.

Well Finally finished this except for electrical. Now they want to add on 16'.

Anyone know how to get rid of them. I got some free mulch from tree guy last year and these things are taking over. The cooler weather hasn't helped.

Only issue I have with spray foam, if you have to remove the building material or have a leak you're screwed. It will have a ridge vent. I think I might add the roll insulation in shop roof area to be safe. I stopped using the bubble wrap because it deteriorates over time. I was at a customers...

I know there have been several threads on condensation with metal skinned buildings. I just framed a 42x72. Should start roof end of week. The first 24' is an insulated shop. R19 walls and R30 in ceiling. Metal ceiling, bottom 8' of walls will be 3/4" plywood and upper 5' metal. Exterior of...

Finally finished. Just waiting on the windmill ceiling fans to come in. Purchased new louvers for the cupola fans. Just need painting and then install.

This has been a slow process. The heat hasn't helped. New LED can lights are awesome.

Thanks guys. Metal is screwed. It has a full apt over the tackroom where the caretaker lives. This is what I use now. Not a good picture but its foil one side white on the other. The white has string in it like shipping tape. Insulation is fiberglass, about 3/8" thick.

Need some of your thoughts. I built a barn for a customer almost 14 years ago and used that bubble wrap insulation under roof. Well its deteriorating and she is tired of looking at it. I have a product that is better but my concern is stapling it to the bottom of the 2"x4" stripping. Won't...

I've been using Maze nails for years. They are hot dipped galvanized and the largest collated nails I've found. If its not hot dipped it isn't going to last. Also have spiral shank and stainless steel. I use them on fences with 2"x6" and 2"x8" boards. About $75/1000. Ring Shank P.T.L. Nails |...

I had a buddy weld some that I designed not hard to do. I used Classic Equine on a project. Not very cheap and not the most expensive. Also installed some from Barnware. Most reasonable were the ones from TSC but nowhere near as nice. Can't remember who made these.

I built one for my wife. Hardly gets used. Hot in the summer even with two ceiling fans. Most of the lumber came from the sawmill. Mortise and tenon joints. Not as nice as Eddie's.

The impact wasn't bad. It was raining and the truck fishtailed. Thought it was going to roll over on the third time. Got it stopped and asked if everyone was ok. Nothing but silence

Brought it home today.

Mine showed up yesterday.

Have a friend that wants me to put up some fence for a pregnant cow he purchased for is daughter. I've put up fence for horses for a long time but not a cow. I was going to use the 2"x4" woven no climb wire like the rest of the fence I built for him. 5" round posts to support it. I've seen...

If an F series and the aux hook ups would I be able to use them for a dump trailer to pull behind it?

Looked like a nice machine. Its owned by a grading company and they use to mow the property. Paint was a little worn, few dents. Tires looked good. Seat needs to be replaced. My biggest question was this. When using the hydrostat pedal there was not a smooth transition from forward to stop or...

Anyone know how to adjust the deck height on a rider 155? I kept telling my wife to raise the deck on the mower because it was too low. I tried mowing and she had the deck all the up. I found a threaded rod by the right front tire that I adjusted but it still seems its cutting too low.

I was at a piece of property today that was owned by a customer. Saw this sitting there. What do you think its worth?

My Dad asked me to build him a wood shed a couple years ago. Well I haven't made the time to do it. I thought I would ask for some ideas from you guys. I was thinking something around 24'x24', metal roof, wood or metal sides. I would like to be able to lock it up so he could leave his log...

Found a 3060 with 290 hrs. Serial # is 20431. Anyone have a clue on mfg date? Or do you know where the date is on the machine so I can email the guy to look for it.

Make it like a sawdust bin I built.

It was this one http://www.tractorhouse.com/listingsdetail/detail.aspx?OHID=9679051 Said I could have it for $12,100. He would service it. Put a new canopy on it, rear rollers on the deck and two new rear tires. The wife drove it around and of course fell in love with it. Big jump over the...

I have a 99 and a 15 F350. I have an enclosed gooseneck that I just put new brakes on. And I have a new 10 ton gooseneck. Neither of these trailers seem to stop well with either truck. I was checking voltage and at the junction box on the trailers I was getting 9 volts and at the axles 8 volts...

Its 42'x96' with a two story living area in it.

I purchased a new hourmeter from JCB which was almost $700. I thought it would be easy to replace with the factory replacement. But when I plugged it in the hour and tachometer didn't work. I recieved some help from another gentleman on heavyequipmentforums.com. He found that Sumiit Racing...

I have to keep pulling the fuel line loose at the bulb and blow back into the tank to clear the line. Is there a strainer on the end? Anyone have experience on this?

Anyone added a block heater to their JCB? Mine won't start when its cold. The guy I purchased the hoe from had bought the heater but not installed it. Do I just need to locate a freeze plug and put it there?

I purchased a new battery for my 212 yesterday because it wouldn't start. Put the new battery in and it would barel turn over. Took it back to NAPA for a load test and they say its good. So should I take the stater off and have it load tested? I know its a Perkins 1000 engine. Are the starters...