Search results

My 08 5530 Mahindra battery was showing 12v and had lights etc;. Took out the battery and had it load tested at our local NAPA. Showed that it had no amps to crank over the starter. Installed new batery and started right off. Batteries are not like they used to be. idaho2

Year of the 5530 and is it a 4wd. Also what Tier is it. Mine is a 2008 Tier 3 (T3) engine. You'll be looking for 30 Series, which covers 5530, 6030 and 6530 if it's a 4wd. Mine came with a CD and Manual. The web site I use is: NEW ENGLAND TRACTOR a division of Johnson Automotive Inc.. Enjoy...

All of our neighbors are 20 acres or more with one exception of 10 acres. Town is 1.4 mi away. Idaho2

Cardan is what came with my 10' Kodiak/Mahindra mower.

I have 35 acres and my son has 60 acres. Combined we have 12 land neighbors for the 95 acres. One of my sons 6 neighbors has a high tension wire, tree blow downs took care of that expensive wire last year and not sure this winter damage yet. Four other neighbors have dilapidated fencing if any...

I have a 10' Kodiak pull behind mower and make frequent sharp turns with no issues with the CV pto that came with it. Idaho2

We have a similar trailer with also a right front side ramp.. I had my neighbor weld 8 or 10 3" eye bolt "loops only" to the top rail. No need for D rings on the floor. Our 835i is secured by straps to these loops. These also work nicely for the ATV's during the hunting season.

Plowing is an art form.

Have a friend with a (used) 35 hrs. 2014 6110 cab. Is wondering if he can upgrade to a ML266 to replace the 161 loader. Found out the 161 loader does not reach like the ML266 does 128". idaho2

VOL54, Measure from the furrow side of the landside to the "Wing of Share" point straight across this will be 12", 14" 16". This is your width. See attached doc. Hope this helps. Idaho2

Bansil, Measure from the outside edge of the "landside" to the outer tip edge of the "Wing of Share". See attached photo, please disregard any spelling error on "landside" this was draw by mouse freehand. This is the width of the furrow for your tractor tire. Hope this helps. Idaho2

Bansil, With those tires on that Ford 5000 look for 16" bottoms. If you have not purchased a plow that would be a consideration. Two bottoms a minimum and three wood be better. The furrow that your plow will make with 16" will be wide enough for the right rear tire and less soil packing...

This a 10-209 Ford Dearborn 3 16's paid $495.00 back in Nov of 2010. Everything was painted blue and in 3hrs of plowing it scoured to a mirror finish. Quite pleased with it. Hope you can find what you want. You can easily remove the third bottom and use two until you need a third. as...

rbtj, Attached photo shows my stabilizer bars with my 3x16's plow. In my opinion, each implement requires it's own three point hook up "settings". IE; top link distance for plows, back blades, box blades and so forth. The lower arms on some tractors have adjustments for each lower arm or...

The mast is the "A" frame and the feet of the A are attached to the Horizontal draw bar (cross member) held together by the two U bolts. Forget anything about the left side of the plow. For clarification the Right lift pin (Cat 1 or 2) is the Large bolt thru the flange that is tapered and this...

Any 5530 owners have this issue of an erratic tachometer on start up. It moves after a short warm up then it bounces high and low before settling down. :confused2: Idaho2

Looking at a 34' x 72' fabric (White roof) storage building with 14'x14' door at one end to include 36" x 80" man door. Level ground, no concrete just rock inside and raised about 4 to 6" above grade and rock aprons at both ends sloped away from the building. Winds mostly from the southwest...

RMOMN, Draft control holds nicely at 8". Just be careful when lifting the 3pt that you do not accidentally move the draft control handle. Regarding your measurements on the rears, I get 48" plow width. Getting a 3pt plow setup takes time and if I plow this spring I will tweak it a little so...

RMOMN I have a 5530 Turbo 4wd and I pull 3x16's @ 8" deep. No weights except a 266ML loader with the bucket for plowing. My plow is Ford/Dearborn 10-209 with coulters. A 6530 should have no problems with 3 16's. RMOMN, idaho2

Skyfish, Here is a photo of my plow and it was all painted blue when I bought it. A plow will scour it's self without you manually laboring to get it to shine. idaho2

Brandi, My plow is similar and my tractor is a 5530. I noticed from your images a few things that I can assist you with. Is your plow leveled right to left and fore and aft. If not adjust the following: Lt. lift arm should be totally collapsed and not changed for plowing. The top link used...

I have a Ford Dearborn 10-209, 3 x 16's with coulters. Yours should scour just like mine after a few hours. Looks like yours has trip bottoms when striking a solid object. Once you have it setup to your tractor the art form of plowing begins. Idaho2

Any 08' 5530 owners, have you had a leak at the hydraulic suction strainer housing flange at the transmission connection. I replaced the O ring but continues to drip although less than before. Question I pose is would a fatter O ring solve this annoying drip. Idaho2

Here's a few pictures of my Ford 10-209 3x16's. idaho2

I'm pulling 3 16" and at 8" depth with my Mahindra 5530 4wd Turbo, AG1 tires, no ballast. The plow is a Ford/Dearborn 10-209 with coulters. Paid $495 from a dealer. idaho2

Here is a photo of my plow the day I brought it home. As you can see I have a three bottom with coulters and mine are adjustable/removable. They are useful in cutting the trash, some folks use them and some remove them. Hope this helps. Idaho2

For any of you 5530 operators what is the max number of bottoms you plow with? Last weekend I got my Ford- Dearborn 10-209 with 3x16's setup. The land had not been tilled in 15 years and was not sure what to expect. What an easy pull that has been for the Mahindra, 3rd gear low range and at...

Jesse11, Is this tree on the south shore in Kennewick? idaho2

I'd bet Lewis & Clark and crew saw this majestic tree and it probably was big then. idaho2

But the day would get intersting very quickly. I saw in the local newspaper the day before about how the city rejected bids on two surplused items. Ok, just local news no skin off my nose. Didn't pay attention to the entire article, but our maintenance man did. He told me he bought a...

TBN'rs, Has anyone notice that on some forum titles, the second response link is an obtrusive ad that has nothing to do with the subject. It claims to be a sponsor link.:confused: Well if it's a legitimate advertiser - join the rest of the advertisers in their column. Maybe the TBN admins...

To all who have had to contend with the white stuff. I have a 5530 4wd turbo diesel, PTO 44hp and looking for your pros and cons on snow blowers 78" or wider that are in use.