Search results

The lights are on the headache rack of my truck, I volunteer my time/gas to escort farmers for safety The lower part shows the handles of the tiller, I said they were crappy but the best I have at the moment

I picked up a dinosaur Wards rear tine with a Briggs 8hp, Model #190402. Long story short it's been sitting in a garage for many years, lucky me there is no spark, I cleaned the points, flywheel and coil, still nothing, so my questions are 1, What are my affordable options? it's in decent shape...

A long reach excavator with a thumb or log clam would be the best. In my area you need permits to do any work on anything from ditches to rivers

The tracked machine we got rides like crap, I prefer the old LS170 open cab over the new 327 with cab

The over the tire set we had on the farm was hard on wheel bearings

Hauled 60 bales, two 30 bale loads, all strapped.

Bent a 480CK loader rod many years ago and a Case mechanic straightened it the same way, 3 months later it bent again and took out the other rod as well with a full bucket of granite

Any chance there is a low oil pressure shut down sensor that's going but not indicating on the dash

apparently you didn't either "when they tried fixing it last time they used an aftermarket hose, it was twisted and the outer rubber had cracked, but that wasn’t where it was leaking"

Late to the converstion but I'd just drain the tank, flush with some good fuel and go, couple hours removing the tank and flushing it is far cheaper than plugged filters and or pump damage

kind of hard to do if working from a dock, even if using a pallet puller I wouldn't move the truck, the receiver needs to have the right equipment or order the load palletized by your equipment's max capacity.

it's all about $$$ and speed of completion

https://www.tractorbynet.com/forums/threads/three-children-one-adult-dead-in-farm-tractor-crash-in-york-county-pa.455065/

I was told to never run E10or any ethanol blend in older equipment, I only run Premium in my power equipment including a 1970 rototiller.

BMW's subscription

Not a lie but a silly idea, think of one of those shake mixer cups with the ball inside doing the mixing as you slosh the mix around :)

When I was on the farm, when ever we went to use a piece of equipment with a slip clutch we would loosened the clutch, engaged the pto to make sure it was slipping properly and then readjusted it, several times equipment that sat for a year or so the clutch would rust/seize together and be a...

Thanks, that makes sense

Once in a while I'll make corn on the cob with mayo and chili powder sprinkled on it then wrapped in tin foil and throw them on the grill or in the oven. Tastes better than it sounds

Only markings are H-10 Spreader tool for?

Not sure of the buying part but the entering part is because of safety concerns, to many idiots showing up and letting their kids run around and adults not staying in their truck. Also most quarry loaders are large and can do damage loading pickups/trailers. PPG's are a must here and drivers...

Maybe it's set up that way so if it's hooked to a 80hp tractor it won't be over powered. Some desk jockey thought it up and figured it was a safety thing to cover their azz's warranty and liability wise.

Not exactly brand specific to your post but don't make the same mistake I did and buy a roll around that I regret now because it takes up to much space. I bought a wide body and now wish I would have went with a narrow tall set up. Must haves are ball bearing drawers and wheels the bigger the...

Sold them 2 Farmall H's, 1 Farmall A and a Farmall Cub

Don't touch anything(it'll void warranty) and contact a lawyer. A friend of mine had the same issue with a Massey Ferguson with 3 hrs on it. Took a couple weeks but a new tractor one size bigger was swapped at no cost

Drag a log behind the front wheels to knock down the weeds/grass while you plow. My Grandpa and Uncles done it that way for years

https://standartpark-usa.com/products/easypave-grid-grass-gravel-paving-system?variant=31148039307353&cmp_id=13481123407&adg_id=129190527571&kwd=&device=m&gclid=Cj0KCQjw0emHBhC1ARIsAL1QGNdpVJiLRelEFcU-r24Divxo81bucjkpKDCT2g1aZqRVwLUB0EQ1NnIaAl6JEALw_wcB

I had a cylinder straightened on a 480 Case and the first time it was used to lift a new bucket for a 330 Cat excavator the straightened rod bent in the same place and the other cylinder gave out about 10 seconds later.

How did anyone get anything done before 4x4 or FWA? To me people with one or another just get themselves dug deeper into trouble no pun intended.

I had it happen to the 3406B Cat engine in my Freightliner. It'll get your attention Inca hurt when black smoke comes out the intake

With the price of lumber a used 48ft flat bed would probably be cheaper

Bit off more than I can chew with my current health issues when I picked up this Yazoo Master Mower. Deck is completely rotted away but I do have a unfinished replacement top. Haven't had running yet. Rear tire leaks. Best offer or trade

I'm new here and this is my first post after spending several hours reading and researching for answers and opinions on the issues a friend of mine is having with his 1533 and hopefully I'm not beating a dead horse. 2006 1533 4x4 with FEL with industrial tires, issues as follows currently at...