belt

Hello guys. Got a friend with a John Deere 320 skid steer. We've been trying to figure out how to work around having to put on the seat belt. Same for the seat requiring weight in it. So far I figured out I can run the seat belt behind the seat and latch it. However if I get out and back...

I am looking for a conversation kit to make one side of my bench grinder into a belt sander. I saw one on amazon that was pushing $300. At the price, I would jsut buy a specific belt sander. Or, any other less expesive options please.

Anyone run a Steiner accessory that requires a belt on a Ventrac? If so what belt size? I have a 4200 vxd and want to try and run a Steiner SC101 stump grinder.

Anyone know a cross for a air filter??? Anyone know the belt sizes?? Thanks

I need to change the fan belt on my John Deere 6400 tractor. Couldn't find any info online about how to properly do it. Was wondering if anyone might provide some directions or perhaps a web link on how to change the fan belt? I don't want to mess things up so I like to have some info before I...

I have a 64 2000 that's converted to a 12V system with an alternator. I need a new belt, and I'm pretty sure when I replaced it the last time I chose the wrong one. So I don't want to use that one as a guide to find a new one. Steiner is calling for an 17/32" x 41-1/4". I'm not finding that belt...

Or should I say "detachments"? As a kid, on the farm we had a flat belt feed grinder. Corn in, chicken feed out. I was young, but it took me all morning to position the farm all, get the belt twisted right, and get corn from the nearby crib enough to hill the dumper to please my...

I need to replace the belt on my 60 inch finish mower. Does the hydraulic motor have to be removed to get the belt around the center pulley? It looks the motor and coupler have to be removed to get the belt off and on or is there some trick to it? Thanks, Bill

I have a 2009 sltx 1050 deck. The belt falls off right away from the idler pulley. The idler pulley bracket and both pulleys doesn’t run parallel to the deck and points down towards the front . Should that be slanted down or run parallel to the other pulleys.

I was wondering if anyone would have any info or manual, for a Vogel & Noot Heublitz belt rake. My father had one and I'd like to resurrect it. I remember using it a little when I was younger and it's been junked for 20 years. Are parts available ? Belts, tines, bushings, etc. Thanks

The belt part No: 754-0461Idler pulley No: 756-0116A Quite easy to replace the drive belt and pulley.

Hello, new here. Does anyone know the trick to replacing the top belt that drives the transmissions on a Cub cadet M54 Tank? I have thought about dropping the rear axle just enough to clear the fans on top of the trans pulleys but don't know if that would cause other problems. Hoping someone has...

I have a 48” Taylor Way finish mower. Lately the belt keeps falling off. I’ve tightened the belt. The pulleys seem to be ok. I am wondering if the v of the belt has to be inward on the pulleys or is it something else? I would appreciate any advice👍

Hello All I'm just wanting to confirm this arm that holds the double groove PTO pulley is bent or not. See picture of arm that has a slight angle to it. I noticed this when I was reattaching the deck mower and I'm even afraid to engage the PTO thinking the belt will just slip off or bust.

I have 2001 JD LT155 lawn tractor with 42" mulching deck. I replaced the drive belt routing atound all guides & pulleys. When I fully depress the brake pedal the drive belt slips off the rear pulley. If I slightly depress the brake I can successfully engage the drive. Any suggestions as to...

I just bought this Kubota T2290 (used) at the end of last year. It had less than 50 hours on it when i got it. Over the Winter my grandson took off the deck for me and put on a snow blower attachment (that I also bought, although I wish I hadn't now). He has since taken off the snow blower and...

My fan belt broked on my Yanmar 2420. I found a belt that fits but I am not sure I have re-installed it correctly. I never really looked at the belt when it was on the tractor. From what I could tell the belt needs to be on outside of the lower raidator hose..meaning I had to take the lower...

I'm trying to run a Ventrac KA160 Blower with a 430 Max power unit. The 430 has the air-cooled Kohler. The Ventrac manual specifies a B52 belt however, that belt is too loose even with the adjuster turned all the way for max tension. Is there another belt beside the B52 that I should try here...

Hello, new member here. I've got a Kioti K9 2400 bought new in Spring of 2022 that has 35 hours on it. When I start it up cold and back it out of the barn, the CVT belt often squeals loudly. Once underway, it stops making noise after a moment. If I stop and shut down for a minute, upon starting...

Wondering if anyone has insight to this. 2017 tractor only 40 hours on it. Whenever the tractor goes to initiate the DPF cleaning the air pump seizes and melts the belt. First time thought the belt was just bad and broke. Caught it the second time, air pump wheel turns fine until it switches...

I have an 1835MHC that I bought this past spring. It is used 80% of the time for mowing. I generally leave the loader off for easier trimming next to objects and only attach it when I need it. I have noticed that with the loader installed that my power steering loses quite a bit of power...