hub

Last week, my cousin called me about his JD mower having a loose right rear wheel. I went over and looked at it, and it looked like the bearing had failed. He brought it over to my shop, and on closer inspection, the hub was loose in the wheel bearing. I'd never seen a all wheel steering mower...

Hi all If anyone happens to have or know where I might find a clutch bearing hub for my MT250D part number 1021 1115 002 new or used then can you please let me know, or evan have a drawing with the dimensions so I can get one made Regards George

I have a JD 4720, noticed the left front wheel was leaking real bad. Found the hub was moving up and down, which destroyed the seal before any other damage could occur. After pulling off the hubs I found Left side hardened washed in pieces sitting in the gear area, Right side hardened washer is...

My little tractor is due for some regular service, in particular repacking the front hubs. These are a little different than I'm used to, they aren't tapered roller bearings, but open cartridge bearings with ball bearings. (they also have a castle nut with cotter pin) Do I still tighten things...

I just replaced both seals on the front wheel hubs on my SA424 after 7 years and only 200 hrs. I use the tractor mostly for the hydraulics lifting stuff that I can't otherwise, the biggest job has been shifting dead Ash trees around my property for disposal (neighbor's outdoor furnace). I also...

Good afternoon, I am currently looking for the hub assembly for my 1984 Massey Ferguson 1030 4wd. I have kinda ran into a road block on finding one to replace the one I just recently broke. is there anybody that could give me any advice on a place that may have this so I...

Just writing about a friends experience with his 2009ish L3540. 1900 hours. It has the LA724 FEL... He has had issues with front axle bearing disintergrating. He is way up on maintenance, he uses all Kubota fluids yet he has had 3 failures with front axle bearings falling apart. Twice, a little...

I have a 2017 Branson 3625 tractor , I believe its 3620 in US. Only 108 hr on it and the front hubs started to leak. I bought it last year with 46 hours on it and have used it for FEL work mainly. First owner bought it new but almost didnt use it because of health issues. I changed all oils and...

Hi All, I have to replace the bearings in the pictured 4-hole hub. Although it may be simpler to buy the whole new hub. A couple questions: Can anyone tell me if these bearings simply press in and out of the hub? I assume that's the case, but I've gotten myself into trouble many times before by...

I need help identifying a John Deere wheel hub. I am running out of ideas, and despite my pride, I think it's time to take my wife's advice and just ask someone. A wheel hub on a custom trailer, which has large sentimental value having been built by my late father, broke due to a freak...

Looking for axle front hub for a 5000 series, 6000 series or 7284 should all be able to make work. anyone with a junk tractor with the parts E-mail me and we can work something out. my tactor is 6284D cub cadet

I have a Satoh Buck S470. It has been owned by my family since mid 1980's and some of the maintenance has been neglected. Noticing the front hub has been leaking. Do I need to replace some parts or seals on the front king pins? Haven't found much info on the front diff, besides thatvit uses...

Need a front hub for ford 3910 fwd. please respond if you have one or know where I might find one. Old part number is CAR119872, newer is 83949437. Thanks

Newbie here. What is the correct hub oil for the front wheel hub. Need to replace the O ring, but cannot find the oil type in my manual. Thanks!

I need some help diagnosing a recurrent issue with my front final end drive on my MFWD T4.75. The sun (part # 5191412) & planetary gears (5165273) housed in the hub locked up somehow resulting in the planetaries loosing some teeth and the sun gear ground completely smooth. The Hub (87542225) was...

I decided to do this myself. I couldn't find any videos on it but I found it really wasn't that difficult. Here is the video I posted. If anyone has leaks or needs info on how to do it check out the video or ask here and I'll see if I can give some good info:

Hello tractorbynet, I have the front axle hub apart on my L3130 (4x4). I want to replace the seal that goes between the hub (part with lug nuts) and gear/knuckle housing. The part # is 34070-13370...I attached a diagram, it is 060 or 180 on it. It is basically two parts...an outer rubber seal...