injector pump

Hi all, I am in the process of rebuilding the CAV injector pump on my 1974 Ford 2000. All seems to be going well, but I just want to double check on one thing: After disassembling the endplate, cleaning, replacing the screen and gasket, then reassembling it, I can shake it and hear what I assume...

I'm looking for any input on setting injector pump timing on a 2006 Kioti ck 25 . its getting harder to start and runs rough for the first couple minutes after starting. Also a lot of black smoke. Any suggestions would be appreciated. Thanks, Len

I have a Northern Lights generator 843n with a Shibaura 3-cylinder motor. Getting the motor to start after it's been sitting for more than 8 hours requires a lot of cranking or opening the bleed screw at the fuel intake hose and priming. 1) Could this be a faulty injector pump, or should I be...

Hello! I have a Ford 3-cylinder diesel tractor with a CAV injector pump and have been having issues it to run consistently. It starts up strong, runs for about 10-20 seconds, and then slows to a stop. It can start back up immediately and repeat the same performance over and over. I have...

Hello. Would anyone know if the slot for the Woodruff Key on a given Injector Pump (in my case a 2011 Branson 3120R A1500; made by Doowan) is always in the same "clock position" on the shaft so that when a new or rebuilt pump is installed the internal timing of the pump is correct as long as...

Greetings, Not having a Repair Manual for subject tractor (do they even have them available yet?) was wondering if anyone has a link to a good site, forum.youtube vid., etc. that gives the proper procedures for removing and replacing the Injector Pump to include setting up the engine ("#1 Cyl...

My neighbor recently gave me a YM1500. He said when he parked it in the fall, it was running.it would not start when he tried to get it started this spring. He put on a new fuel filter and tried to bleed the system, but there is no fuel coming out of the injector pump to the fuel lines. I...

I have a Iseki TX1500 with KE75 Mitsubishi 2cyl. I have had one heck of a time getting it started after having set for year. New diesel filter, bleeding at filter & inj. Pump. Cracked lines at injectors. As engine turned over, closed off each bleed point when air bubbles stopped. Noticed 1st...

I have a 2021 Branson 4820h with a Kukje engine Ser number TX3K00116 With 290 hours it's a hobby machine kept in an enclosed garage, serviced regularly, fuel is clean, fuel bowl clean. Here is what happened: Recently while doing some light work it start smoking and the engine began running...

This will be a long one, Apologies!!! Afternoon, as the title states I am having issues with my 5310. It started around a month ago. Ran fine then would turnover but not start 2 weeks later. Trouble shot the whole fuel system and fuses etc. After doing some more research, I found the Temp...

I have a ford 1700, 1987. How do you remove the injector pump?

Recently i cleaned my CAV injection pump because everything was stuck. After this starting was difficult and the throttle at idle speed was no longer in its original position. What did i do wrong? Used govenor spring code number 3, is this correct? The older pump has the following numbers: CAV...

How do you adjust the timing on the injector pump. I notice there is some adjustment that can be made by rotating the pump possibly. Any info would be appreciated. Thanks

I have a issue with what I believe is a fuel problem. It seems to be getting to much fuel in the cylinder. It starts right up and runs great but there is a black soot mixed with diesel coming out of the exhaust that gets all over the tractor. I am a new owner of tractor so don't know the past...

I bought this Massey 245 with the ad3.152 Perkins diesel in it. Not running Injector pump was not delivering fuel to injectors, plenty of diesel was comming out of supply line to injector pump. I disassembled pump and found that the stop bar inside the top cover was frozen in the off...

The tractor has been sitting unused for a few years. I have fuel going in and coming out of the return on the injector pump. The fuel shut off solenoid clicks hard like it's working, but no fuel comes out of the injector line ports. Something is obviously stuck, frozen up with the fuel shut...

I have a leak in my Lucas CAV injector pump on my Perkins 4.236T engine. Its leaking from that long extension from the bleed screw hole. I have tightened the 7/16 bolt head to sensible level but i still have a weep. Anyone have a part number for what I need to repair that, i would like to...

Hi all. First Post and a bit of a hail Mary. Have an injector off of a fiat 780, and upon taking it apart it seems I've broken the shaft between the head and rotor. I've scoured the Internet and can't find anywhere that has that specific head and rotor. Can anyone point me in the right...

Attached is a photo of the timing gear box for the fuel injection pump on my Branson 4220 tractor. As you can see, there's an orange filler cap marked "oil". I looked through the owner's manual and the engine manual, but I see no reference to this oil fill hole. I stuck a finger down the hole...

Need help with governor spring code on a CavLucas Injector Pump DPA R3448F040, Model 30280 EDG. Type RE 11803. The spring came off the throttle shaft during reseal.

Hello everyone, I rebuilt a 95 New Holland 268 engine I now have 50 hours and it's still hazing at idle with unburnt fuel. The book was very vague on timing the pump. What I did was used a dial indicator got the #1 on top dead center lined up all my gears and installed the injector pump with the...

Hi all, I have a Cub 7234 with about 700 hours on it. We love the tractor, it is used to brush hog our pastures and drag our arena and gravel drives. My kids were running it last week and the engine ran away. It over-revved (my son-in-law said the tachometer was pegged at 3000 rpm) and...

i need to replace gaskets on the back of the fuel injector pump. Is there a special tool that I need to use to remove it.

Im tring to find a place to buy some parts this engine it’s a K3B I believe . I live in ontario canada . Any leads in which this engine was in so i can find a dealer and give them a part number would be great . Im missing a couple parts from within this pump. There is a spring a small what...

Hello, I have a Shibaura SD 1800 that has an injector pump that is bad. Where can I find a rebuild kit or replacement pump and the diagram for it? Thanks and God bless!

Hello. I have a 254 Chinese tractor with 3 cyl. LaiDong engine. The crank case keeps getting filled with diesel fuel somehow. I'm guessing the fuel is getting through from the injector pump maybe? Are there perhaps some kind of seals in the pump that I could change? Or a leaking gasket maybe? If...

The temperamental and very expensive Lucas pump ($3850 ) was unrebuildable so saw some guys we’re replacing with the old mechanical Bosch pump. I installed a new Bosch pump. Had the injectors recalibrated. Replaced the drive gear and rerouted the hard lines. Installed new lift ( supply ) pump...

Evening all--new here, and have what I think is an injector pump issue. Bought a Yanmar 1700 in pieces a bit ago, put new head, rings/piston and injectors in. Starts easy with the decomp valve and runs, but has a lot of White smoke--thinking it's not burning all the fuel it's dumping through...

My 2004 Case DX35 was running just fine, but I had a little fuel leak in the injector pump. So I pulled the pump and injectors. I am waiting for the return of my injectors and a new injection pump from the shop, Precision Fuel Injection in Honolulu. My old pump they say had a bent part, so...

My 2004 Case DX35 was running just fine, but I had a little fuel leak in the injector pump. So I pulled the pump and injectors. I am waiting for the return of my injectors and a new injection pump from the shop, Precision Fuel Injection in Honolulu. My old pump they say had a bent part, so...