kubota b7510

My kubota b7510 will not start. In the fuse box the middle fuse 10 amp. Will blow when i try to start it. Have check all the wires that are expoesd now unsure what to do next?

I went out to start my B7510 and there was no power. Turned the switch on and heard a slight buzzing sound sort of what it makes when your battery has gone bad. After that nothing. No lights on the dash nothing. So I put on a battery charger and the same thing. The date on the battery was...

I need to cut off and weld on new ball joints on the drag link for my 2004 Kubota B7510HSD. The drag link is the rod that goes from the steering gear box to the knuckle arm. Does anyone know where I can buy the correct ball joint ends or does anyone know the specs of them (taper, etc.) so that...

Hey there, hoping someone can help me out. I bought and downloaded the workshop service manual for the B7510 online but it doesn稚 have the wiring diagram with colors. Looking if someone has or knows how to get that wiring diagram. Thank you!

New to the forum. I'm looking at a used 2007 B7510 and trying to get an idea of what is a fair price to pay for it. It is in very good condition. It does not have a loader and has about 600 hours on it. Tires are good also. They are asking $6500 firm for it. Thanks for any help.

so I've just joined this website in an effort to get the right info so I can properly change the transmission oil in my B7510. I've done a ton of reading online. My manual and website info says that the capacity is 15.3 litres. After carefully following instructions on Messicks (best i could...

We have a B7510 that suddenly stopped moving during use. It will not go forwards or backwards. It makes no noise whatsoever when depressing the HST pedal. All linkages are intact and operational. This tractor is used by teenagers so someone cut off the PTO and H-N-L levers to make it more simple...

I replaced the lift pump but still do not get fuel from the output side of the new pump. I am getting fuel to the input side of pump. Any help would be appreciated. Richard

Coming up to 600 hours on my Kubota B7510 which runs a 5' belly mower and a 4' bush hog. When I changed the oil and filters at 300 hours there was no evidence whatever of anything but pristine oil and clean drain plugs. Have all of those old HST Kubotas really had their oil changed every 300...

Can anyone tell me where I can find how much my tractor is worth? It's a B7510 with a LA302 front loader and a 4672B backhoe, it has 188 hrs on it. 2007 stored inside most of it's life.

Just brought home a new (to me) Kubota B7510. Realizing now that mine does not have a foldable ROP loop and also that it will not fit in the shed I want to keep it in. I'm not able to find much used out there specifically for this model and wondering how many other series tractors this ROP will...

I am wondering if anyone has used a B2781A 51inch front mount blower on a B7510HSD machine. I have had the Bx2750 blower for the past 8 years and it needs to be retired. I clear a driveway about 1400 ft long and 2 cars wide with a fan out to a 3 bay garage. The driveway is partially paved...

I recently put a couple of tanks through the Kubota B7510 trimming around 15,000 tree seedlings with the 48" Braber rotary cutter. As long as the grass wasn't too long it did a good job. When I tackled a one-acre hay plot, however, it did a lousy job. The tractor's wide turf tires flattened...

I just finished changing the hydraulic oil in the Kubota B7510. It's quite a job. I'm told HST machines live or die on the condition of their oil, so it needs doing every 300 hours. The previous owner told me he had done it just before I bought the tractor at 210 hours, but he apparently went...

I've noticed a few older posts on L series Kubotas with front axle leaks but nothing on a B7510. I'm looking for advice on changing the seals. The front axle seems to be leaking from the top of the housing (see arrow in attached photo) on both sides. I found a couple exploded parts diagram...

Does anyone have experience matching a snowblower to a Kubota b7510? I may buy a used blower or cut a bigger one (72 inches) I have down to an appropriate size. The manual isn't really clear on what is appropriate. It says a maximum "digging depth" of 60 inches and 400 pounds. I assume they...

I bought a one bottom plow from TSC and cannot get it to work. I cannot convince it to roll the sod over. It rises up, leans over and falls back in the furrow. I have adjusted my lifting bar up and down, I set the tractor rear wheel in the furrow, after I got off and hand turned the sod by...

Can't start this thing it is a great tractor but have been having trouble starting it with key. I turn the key to glow plug, it sets, turn to start position and nothing. Battery is up but no start. It's like the transmission is not returning to neutral position or a bad neutral safety switch. I...

I like to know if anyone has any instructions or diagrams on replacing a water pump on a Kubota B7510HSD. What do you have to remove and how and any torque on bolts required.

After 15 hours of mowing our rather rocky green space, the blades on the mid-mount mower of the Kubota B7510 I recently brought home need service. The centre blade came loose yesterday and I was able to find a 30 mm socket and breaker bar to reach in and tighten it. I also touched up the ends...

Hello All, I'm a proud new owner of a Kubota B7510. I purchased this tractor second hand. It's the first Tractor, first diesel, first hydraulic piece of equipment i have ever owned. So i will have lots of questions over the next year or so. For quick introduction. I am no mechanically...

I have had my backhoe for a couple of years. This thing is hard to store and even harder to move around the shop. I finally decided to build myself a dolly, with a few requirements in mind. The first being it had to be the perfect height to install on and remove from my tractor. Second, it...

WHERE CAN I GET A SHOP REPAIR MANUAL OR A WIRING SCHMATIC FOR THIS MODEL KUBOTA

I am in the market for a tiller for my Kubota B7510 and was looking for suggestions and or advice. I was hoping someone has the same tractor and can give some first hand experience on a tiller that has worked well for them. I was looking at the KK XB series as well as a Phoenix tiller. Thanks in...

I need more down pressure on the Land Pride PD10. They make a down pressure kit for it. Anybody know if I have to also install an additional valve to actuate the down pressure cylinder on a Kubota B7510?

Looking for wiring how to for additional lights on my Kubota B7510 ! Any diagrams ,etc would be helpful!

looking for free download of owners manual for Kubota B7510 , also service manual. Knothole29@hotmail.com

When I bought this tractor, I never thought I'd need more than a bucket. How I can now see the error of my ways. I would love to have a set of pallet forks, bucket and something I can use to move trailers around the yard. Is there any way to add the ability to drop the bucket easily to this...

Bought my first tractor, B7510 two mos ago, Wylie, TX (near Dallas) still looking for backhoe....any help locating one or advice will be greatly appreciated.. tractor still at dealer (Roberts Tractor, Wylie, TX..........I need it to help build house, dig septic and cisterna, dig trenches for...

Just bought a 2008 B7510 and this original factory set leaves much to be desired.It slants forward and is just basically uncomfortable. Does anyone know where to get a replacement besides paying $ 200+ from the dealer ? Did Kubota offer a free replacement due to their terrible idea of using this...

I have looked and looked but I cannot find the exact location of the rear drain plug or oil strainer for the hydraulic UDT fluid (I have searched the web and my tractor). I have found all kinds of pictures of B-Series tractors. I have also been to Messicks website and looked at those pictures...

My B7510 does real well around the yard with the R4 tires, but I need R1s for disc and other field work (I can't even pull a medium heavy trailer uphill if there is any green or moisture). I tried to find R1s that fit the R4 rims, but no cigar. Where can I find the best price and what size...

Can anyone tell me where to get a free parts manual or if you have one can you send it to me. Can not stand paying $$ for a pdf manual. Someone must have one already. Thanks.

I went to look at two used tractors today. Both 4wd with loader. I liked the MF but am concerned with the ground clearance. It seems kinda low. It has turf tires on it, I am trying to find out if I put tractor tires on it will it raise it some? He's asking 9500.00 it has 190hrs., any pricing...

I am looking at used RCB54-24B Mid Mount Mower decks for my B7510HST tractor. I've never seen one and would like to know how it mounts so that I'm sure it has the right brackets. Does anyone have a manual or could email photos of the way it mounts. It would help me out greatly. Thanks in...

I am in the market for a FEL for my 2004 B7510 and have checked Craigslist for about a 500 mile radius and have found nothing! :( so I called some dealers and got prices on a new loader, Help me out I now nothing about them and there are several manufacturers of fells out there. I got a quote...

What are the pros/cons between these 2 tractors. Both have similar power & hst and 60" mowers. What are the noticeable differences? Tires are bigger on 7510.

I have a 7510 that had the same noise as described on your forum. Transmission noise under no load. Noise leaves when tractor is pulling. The fix is very simple. The dust cover surrounding the drive line going to the front axle has a nylon bushing in the end next to the transmission. The...

Purchased a used RCK60-24b to mount on my B7510HSD and I'm having trouble with the mid hanger on the left hand side rubbing a hose. Please see the picture, I'm not sure what that hose is for but it appears to come off the transmission and run to the back. Thanks Mark

After two years of owning my B7510 I was finally forced to leave it outside my garage. A small tear in the seat got larger in the cold weather and now I have to replace (Yup, I forgot to fold the seat forward). I find the stock seat a bit basic...anyone have recommendations for a replacement...

Price check for a kabota b 7510 hst?

I have a new (to me) Kubota B7510 with a FEL and am using mostly to haul firewood, rocks and moving some dirt. I live in the mountains of NC and, while I have established tractor paths with safe inclines, I have been going slow and easy learning what I can safely carry up and down the grades...

Admittedly, I am a novice..... I want to make sure I know where the engine oil drain plug is. The Owners manual is not clear to me. One post I read made it seem like it was inside the oil filter. Any pointers for me? Thanks, Jeff

Looking at used. I don't see alot of difference other than BX2200 newer model. Equiped with FEL and brush hog or box blade around $10,000--little less. Would kindof like to have mmm but don't seem to be on many of the models. Which is best and why? Am I missing something? Thanks

Tractor wouldn't start, let it set a day and it started. Started fine for 3 weeks. Now, for the last two weeks I can't get it to start. Crossed selanoid, and checked all 5 safety switches. Haven't checked the starter or key switch. Any suggestions. The dealer said that it might be a dirty...

Just want to let folks know a situation I ran into with my tractor. Nothing bad just a heads up if you have a B7510. Ever sine I had my B7510 I noticed that the power was not that great when moving materail a brush hoging but I just chaulked it up to the 21 HP motor. Well I took it into the...

I just saw this Kubota tread - Anyone have a recommendation for a tiller to fit the PTO on a B7510? Place to purchase and price?

Anyone have a recommendation for a tiller to fit the PTO on a Kubota B7510? Any idea on price and place to purchase?

For sometime, my 5 yr old B7510 HST would continue to move slowly forward when pressure was taken off of the pedal, and often would have to tap the reverse pedal to stop it. Sometimes, the tractor would not start until the pedal was re-centered. This happened yesterday and again I tried to exam...

Hi all, I have been surfing the site for over a year now and have owned my B7510 for about a year. New to tractors, but I feel with all the information I have received from this site that I have been around tractors for years. My question, curious to know if I stand-up out of the seat when...

Anyone know the bolt size for the Kubota B7510 seat? After my first seat got replaced in 2006 with one from Tracotrrs Supply, I recently ordered the new upgraded seat from Messicks and I dont have the bolts for the OE seat. Anyone know the length and pitch I need so I dont have to haul the...

I'm trying to decide between these tractors. I have a little under 2 acres about half of which I will mow and the other half is wooded with large trees (some of which I may try to establish and maintain as a shaded park/lawn). I have some pretty good slopes on the property so the higher center...

This morning I started my tractor and it was making a whinning noise. The sound goes away as soon as I push in the clutch pedal. It sounds like a bad throw-out bearing??? Is there one on a HST? I was wondering if there something else I could do to troubleshoot this problem, is there a clutch...

Hello everybody, first post. I found this site while looking at ar15.com asking about this tractor. Anyway, my wife and I just purchased our first house in the country. We are looking to move in in a couple weeks and our push mower won't work out so well because the house is on four...

Just came across this Bend, Oregon Craigslist post and it doesn't sound like too bad a deal if you happen to be located within reasonable distance of Bend. Anyway, here is the ad. 2006 KUBOTA B7510 WBACKHOE - $17500 (BEND)...

Looking for a tiller for general use. The B7510 has 16 pto hp...looking at CCM CR50 or the MR130, like the fact the MR130 is much heavier...but it requires 15 hp the drive, Both are the same price. Which is the best for my B7510? or other options?

I started looking for a set of chains for my 7510 rear tires (TURF TIRES). I have been looking for an excuse to get chains and now it came up. I will do some logging pretty soon and want chains on for that, because of some soft spots on the logging road. I want to get the work done before...

Hi all, I just purchased a Kubota B7510 with R4 tires and a rear-mount field mower. I purchased the mower for my field, but my backyard had a growth spurt and had to be mowed with the tractor. To my pleasant surprise, the tractor didn't tear up the lawn. I was considering buying a Snapper...

I thought it would be nice to plow with my B7510 HST Kubota so I built a subframe and plow last month. I started with an old meyer 7 foot blade. I cut it down to 5 foot and re-skinned the bottom 6inches. The subframe was made out of lots of bits and pieces I had around. The tubing is 2x4x1/4...

I am looking for a plow attachment for the FEL of my Kubota. I have heard of a company called Guest Industries out of CT, but I was hoping to find used, as I want to save $$. Anyone know of anywhere I can look in MA / NH? Thanks.

I'm wanting to sell a 2004 B7510hsd 4x4 with fel with 430 hrs. and don't know what to ask for it, so maybe you guys could help me with a figure. I also have ten implements: Taylor-Way tiller 48", Woods finish mower 60", Bush hog pulverizer 60", box blade 60", Taylor way grader blade 60"...

Was wondering what I would expect to pay for a B7510HSD w/foldable rops, kubota fel and bh? Just a ballpark figure. I live in northeast PA and have access to 3 quality dealers. Looking at the B series versuses the bx series. Any help would be greatly appreciated. Linedog

I have a kubota 21 hp B7510HST and have questions about putting a 3pt backhoe on it. Will it work without a subframe or will it twist everything? If it needs a subframe, about how much is it's cost installed? Will the hoses used for the hydraulic top link tilt be sufficient? Harris

I am wanting to do my own 50 hr service. I know that the oil and oil filter and the hydrolic oil and filter need to be changed and grease points, but not sure about any other stuff. Also what kind of oil should I use. I see 10w30 and know that it has to be diesel rated...but what about synthetic...

I have a 7510HSD (love the tractor) but it causes severe radio interference to AM radio stations if the radio is in close proximity to the tractor. The interference does not occur at idle, but at any RPM greater than 1200 it is severe. It does it no matter if the tractor is hot or cold. Is...

Just traded in the BX2200 for a B7510 HST and was looking for the site that will give you a copy of the tractor parts listing and numbers in PDF a format. I got the PDF for my BX2200 a while back and can not remember URL. Thanks for your help in advance.

sadly, i have put my b7510 up for sale. it is in the classifieds.

My father-in-law borrowed my B7610 to move a huge pile of dirt he had left from geting his drive paved. Now he wants one. He has a couple of old Cub Cadet garden tractors, an old Dixie Chopper and an old Oliver that doesn't run most of the time. He said he was thinking about getting rid of all...

I am considering trading my BX1800 for either a B7510 or B7610. I need a machine with a little more ground clearance and capability. The difference between the B7510 and B7610 is about 3 Hp and approximately $900. I run a 48 in tiller, 4 foot bruch hog, rear blade, stone rack and 60 in mower...

I got my new 7510 yesterday, along with the FEL, 48" Rotary Cutter, Box Blade and Landscape Rake! Dealer even threw in some Ball Caps! I spent a couple of hours playing..errr....working last night before we got pounded with hail and heavy rain. Very pleased with the tractor and the great...

1) I have read that some implement attachments operate better using the float position on the 3point. However it seems that the B7510HST does not have one. Can anyone with this tractor tell me if I am missing something or is there another way to make an attachment float when using a bush hog...

I have a friend who has offered me the use of a PTO driven post hole digger. My tractor is a 21HP B7510HST with a PTO of 16HP. Is there anything special about phd's that would limit my use of this. Is the 16HP PTO sufficient to use a 6" auger? Harris

Things do happen fast. I thought I was going up hill but the hill has a compound slant. My front wheel went into a hole I couldn't see and before I could react, over I went. It actually wasn't a frightening as I thought it would be. It was easy to get it back up on the tires using a strap...

I've been looking hard at tractors for the past few months. The <CEO> may/may not finally let me pull the trigger in the next couple of months based mostly on the prices I can come up with versus the financial state of the household. My land is 5 acres, mostly covered with a not-too-dense...

Hello all - I am a new owner of a B7510. I had a local guy over to do the 50 hr service and I noticed the Super UDT fluid level as indicated by the yellow dipstick seems to be way over the high level (although it is difficult to see very well). The interesting thing is that the spec chart in the...

What if anything are you doing to carry tools? There's no room behind the seat and the little one under the seat is good for about a screwdriver and a adjustable wrench. I was thinking that I might attach a bracket to the bracket that holds the safety triangle, attach the toolbox to that and...

\'04 Kubota B7510 Considering up grading to a bigger tractor and need to sell mine first. 2004 B7510HST with 302 fel (316 hrs) also have a box & grader blade, Taylorway Pittsburg tiller, and bushog brand pulvierzer all 5'. Could I get some ideas on what its worth or where i could find out...

My B7510 Turf Special and it\'s property... 16 hours on her so far!

I am looking to upgrade my BX2200, so I am wondering if you folks have any thoughts on pricing on the B7510HST w/loader? I have not tried talked to the dealer yet. Here is what I am thinking. They have both of these on the lot. B7510hst with 302 loader. or B7510 turf special with 302 loader...

Both have FEL and 60" MMM, HST. My local dealer quoted $13900 on the BX2350 and $15850 on the B7510. I went in with the idea of the BX but he steered me toward the B. Any thoughts on the price and the choice would be helpful. In the end I will use the tractor for small jobs on a 6 acre site...

Just droppin in to say hey. Picked up a "last on the lot" B7510 Turf Special today. Cut 3+/- acres in about 2.25 hours without a glitch at all. Nice to know there is a message board for tractor owners. See you guys around! Chris

I’ve read a few posts on TBN that said the limiting factor on the larger B2710/2910 and MMM was the deck belt...they said it would squeal before the engine lugged down in tall wet grass implying the engine had more power than the deck could use. I’ll assume these belts and spindles were in good...

Guys, My B7510 HST turned over 50 hours this evening while I was grading an area around our new pool. I would like to perform the 50 hour service myself and was hoping that I could get a parts list of what I need to buy to complete the service. Any and all help is appreciated as always...

I've reached the 50-hour service point and changed the oil in my B7510HST which I've had since last June. Filled up with Rotella 15W40 oil rated for diesel use. Couldn't find any diesel-rated 10W30 or 10W40 oil that's recommended in the Kubota user's manual. TSC, NAPA, WallyWorld all sell the...

Hi, I am new to this forum, but have read some of your discussions so I decided to join. I have a Kubota B7510HSD. And this is the first real tractor I have owned. I am wondering if anyone can tell me where to tap into the hydraulics to add a rear hydraulic remote. My tractor already has a FEL...

buykubota-ML-797914-ML- Brand specific. Moved to Kubota Buying/Pricing forum.

I have the opportunity to buy a Kubota B7510 with a 60 inch mowing deck and a front end loader. With 135 hours on it. Not sure of the year, or how the tires are, but they are asking $13,000 for it. Its from a private party, and in good conditions. Is this a good Tractor, Price and Hours? I...

Okay, I have been driving myself nuts with this for a month now. So far, bought an L2800 gear and cancelled as a single stage clutch and pretty bad for mowing. Emailed Kubota and they are convinced no problem, but I don't think so. Decided to go with an L2800 HST and when I saw this beast...

Normangee Tractor in Normangee, TX has quoted me $11,200 for a B7510 4WD gear shift tractor with FEL. Is this in line with the market? I want a PHD (post hole digger) to go with it and the quote for that was $695. That seems high to me, and the explanation was that it is shorter than the...

I am a newbie to the world of tractors and am in need of some advise. From what I have read, this is the right place to be! I have 10 acres, 4 of which I have been mowing with a cub cadet riding mower with a 50" deck that I will be using the tractor for. Just takes too long with the cub cadet. I...

I'm a relative newbie to the tractor world, other than toying with the idea of getting one for a couple years, and having a little experience operating FELs and BHs. It's time to make the move. I have 5+ acres, 3 or 4 horses, need to regrade and expand the riding ring, dig some trenches (a...

I'm having a devil of a time getting Kubota dealers to give me a price, but the one I have gotten for B7510HST with 60" MMM is $10,575. That's an up-front number , so I assume it could go lower. How does that sound? This is in Georgia.

Anyone out there have any experience, opinions, recommendations, etc. about using a hydraulic post hole digger, like the Land Pride HD25, bucket-mounted on my tractor for downforce in pretty hard clay soil. Need to drill up to 12" dia holes 3 feet deep. The 7510 only pumps 7 GPM hydraulic while...

My wife and I are in the process of buying an 8 acre farmette in West Virginia. Half of the property is grass and half woods. I have been reading through this forum for a few weeks and between the advice here and my research, I have narrowed my choices to the Kubota B7510 Turf Special and the...

Thanks to the members here I finally decided on a Kubota B7510 (after taking a couple years to convince my better half) and had one delivered on friday with a 302 loader and Bush Hog SQ480 rotary cutter. So far I've only got about 6 hours of seat time but I've gotten a lot done around here (at...

Hello, New to TBN, i live in upstate NY, 1 hour north of Albany. Looking to purchase a b7510, with a fel, and a mmm. I visited Salem Farm Supply, and was given a price of $14,200. Does this seem fair? I have heard a lot of good feedback from people who purchased equipment from Salem, and i...

Anybody bought one? Or seen one? I went from a B7500 last year to a B7510, and at that time considered going from the 60 MMM (ground contact) to the 54" MMM (suspended). The dealer talked me out of it. I always wished I had the suspended style MMM like the BX runs just because of how bumpy...

Hi all, just received a new 7510 on Friday. After 3 hours backhoe & loader mixed operation the main boom on backhow started to "stutter" a little and I found I had a hydraulic fluid leak where the line exits the pump -- right where the fitting enters the pump body. (probably had about 2.5 hours...

I am have been reading TBN for about 6 months and have gotten a lot of good info. I was looking at buying a tractor in the next 3 months. I started shopping on the net and was looking at all brands for a CUT with a FEL and a 60" finishing mower. I went shopping last weekend to look and in up...

Please help me with my choice between these two tractors? The JD has 2 horsepower more, but cost C$4000 more with the same size tiller,mmm and FEL. Will be used for mowing, some ground work. The size of land will vary in future, likely bigger, therefor the bigger tractor. It's for a...

I was looking to buy a small Kubota BX 23 or a B7510 and THEN... I saw the Kioti web site and now I am interested in a Kioti. Did any of you look into either Kubota the buy a Kioti, and if so which one did you purchase. I am in need of a FEL and BH only (no mowing). I hope you can help me...

Very new to the site and the tractor world, I have been looking at few the last couple of months and have a few questions.. I will be mowing about 6 acres of grass in VA and have been looking at the above tractors. I can get a used B7510 with 50 hours or go new with the BX model after setup...

I was set on getting a B7510, but I was speaking to a dealer and he recommended geting an L series tractor. He said they are bigger tractors and true category 1. I was under the impression the B7510 was a cat 1 tractor. Also looking at the spec I don't see that much difference between the...

Hi All, I grew up with tractors and currently own several with regular manual transmissions. Am now looking at the B7510 or B7610 for light utility work including some linear mowing (along roadsides, etc.) and road grading. I drove the HST models and didn't like the foot pedal arrangement for...

Question 1: B7510HAD 5 months old, 175 hours. LA302 Loader, Bradco Backhoe, R4 Tires. $14k. OK? Question 2: Best source for B7510 parts? Question 3: Best manual? Source? <font color="blue"> </font>

I was about to purchase the B 7510 and the JD dealer called. Here is the deal. B7510 with 302 FEL, 60in mmm and 48in box blade for 15422 including taxes at around 735 dollars. JD offered the 4110 with 410 loader 60in MMM and 48in box blade for 15650 before taxes 782.50=16432.50 For the one...

5\' King Kutter Box Blade for Kubota B7510? I am in the market for a box blade for my B7510 and need to know if a 5' would be to large. Kubota recommends the 4' box blade, but I want to get enough width to go around corners and do not think I could accomplish this with a 4'. From what I...

Please give me some guidance for purchasing a CUT. My options are Kubota B7510HSD vs. Kioti CK20HST. I have only test drove the Kioti and it seemed to fit my needs and the looks are pretty impressive. Although the Kioti seemed to lag up a small incline in high gear with pedal fully pressed...

Does anyone know where i can get wheel weights for the 7510. I checked a website called ezweights but think they are no longer in buisness(Never reponded to my email). I would like wheel weights instead of filling the tires. I do alot of brushhogging in wet swampy areas and less weight means...

Just got a quote: B7510 w/ -FEL -BH-13" bucket (Bushhog brand) -4' bush hog (not sure what brand) -4' box blade (not sure what brand) -5' RMM (Land Pride) -16' trailer (tandem axle,bulldog hitch,trailer brakes) $19870 plus tax. Backhoe is still up...

implement-ML-551108-ML- Moved to the Attachments forum.

Looking for opinons & advice on 3 PT. tillers that you own/ have used for this tractor Kubota B7510 All opinons welcome!! (but would really like to see testimonials good/bad from your personal experience)! Thanking you in advance for your reples!!

What is the biggest brush cutter I can operate with this tractor?

Hi, I've been reading and learning all about the kubota compacts on this forum for the past several months. As a newbie I knew nothing. I've learned enough to be dangerous and now I'm ready to buy and am wondering if there is $1000 dollars worth of difference between the 7610 and the 7510...

Any one have info/experience with log splitters mounted on A B7510 tractor? (or any other) 1. Kind 2. Make etc. 3. Recommendations! Thank you, Dean

I just wanted to thank all of you who have contributed your experience and expertise to my purchase today of the following: B7510HST 302FEL 4672ABH W/sub frame 12"Bucket Folding ROPS R4 tires Ballast Bucket Two grab hooks welded on loader bucket 50 hour service provided PU/Del included...

Hello. I have been reading on this site for a while now. Been looking at many tractors trying to properly "size" my new toy for my needs. The local dealer had many BXs in stock but no B series at the moment. Anyway. I was wondering if anyone knew the tire size for turfs on this tractor. All the...

I sat on a B7510 seat yesterday and it sure beats the pants off the one I have... well my B7500 seat beats my pants compared to the new seat! The B7510, or what appears to be all of the new "B-Line" seats, seem to be more comfortable, more erect, and just nicer in general. Anybody retro a...

trying to make the decision between both of these tractors. The kubota was quoted at $12400 with loader while the 4110 was quoted at 14300 with loader. Am i missing something. Whats the difference it seams that they are pretty much the same tractor. Please help.

I am thinking about buying a new tractor I have narrowed my choice down to a Kubota B7510 or B7610 I have priced them with my local dealer. Both tractors would come with a 60" mmm and a 302 fel. The price is about $800 more for the 7610. Is three more horses worth it? I will be mowing about...

Came in on Friday. Unfortunately, I'm also building a house up there, so only got to put two hours on the beast. Great machine, easy to operate, and very fun, too.

Yup, it's being delivered in the morning. Just so happens that I also scheduled delivery of 12 yards of road gravel to play around with this weekend. The tractor, FEL, 60MMM and 5' rear blade is setting me back just over 15K. Pictures to follow early next week. ACTION pictures; dirty...

\'57 Ford died, NEW B7510 coming soon Nice board, lots of great info. About a week ago my Ford 600 threw a rod bearing, so I was left with the choice of rebuilding it, possible $2500, or cutting my losses and getting a new tractor. The BX2230 was my first choice, but based on what I've read...

Hi, I have been lurking here for months learning as much as possible and I finally bought a B7510 (pic attached). She arrived last Thursday and came equiped with filled tires, chains on the rear and a block heater. It was -20 F the day she arrived so I didn't get much seat time in! Attachments...