kubota bx1800

What the thead size on the steering cylinder or the Tie Rod for the BX1800. I damage the threads and need to clean it up with a Tap/Die. Are they 14MM? TIA, Don

Mine is a 2003 BX1800, and I "thought" I ran it out of diesel....but its not firing when I try to restart. I think ive isolated it down to the fuel pump (ie:its dead) but wanted to ask the brains trust if there was any other way to bleed the fuel line? I loosened the screw on the point where...

My dad owns an older Kubota BX1800 with a Diesel engine and has been having some issues with it. It starts and runs fine but after about 30 - 45 mins of mowing it starts to sputter and then dies like it's out of fuel (which it's not). If he lets it sit for a good while it will crank back up...

I have a 10 yr old BX1800 that I love…except…I can’t get the starter be fix to engage. When you hit the starter, the be six tries to pop out but isn’t aligned correctly and doesn’t engage the larger gear. I’ve replaced the starter with twice now, thinking it was the be six not pushing hard...

The cylinder on my snowblower is stuck. $359 for a new one. Is there a way to get one the same size cheaper or should I try a rebuild?

My old man just picked up an older BX. Pretty light in the rear. Anyone fill their rear turf tires? I know they are pretty small so not sure if it is worth it. Thanks for any info.

I purchased my new to me BX1800. I believe That this tractor sat in the south west sun for 10 years after the owner destroyed the transmission by stomping on the differential lock when the right rear tire was spinning. The result was the final drive, brakes and Main transmission case were...

Greetings, Recently bought a Kubota BX1800 with loader. When I picked it up it was in pieces. The transmission main case was destroyed and I just finished rebuilding it. It runs great and have used it for a total of 8 hours. I didn't like how the tractor beat my back up so I put on a...

Love this little tank, it's like the energizer bunny. It just keeps going and going. Now, the bad news. The steering is starting to act funny. I'm constantly have to turn my steering wheel, just to keep tractor straight. Sometimes, not all the times, I will have to turn it 360 just to keep...

I have a BX1800 which I have owned since 2002, has 984 hours on the clock and has been pretty bullit proof however, recently while using the tractor I felt something let go in the PTO selector lever when shifting. Now the only position the PTO will work is the rearward position, Mid/rear. If I...

just mounted my 54" mower cut the lawn, noticed when mower is in up position it rubs on the back wheels. Need a solution. Thanks

My husband's Kubota BX1800 will make the clicking for the glow plug when you turn key to first station, but when you turn it further there is no sound whatsoever and it doesn't start.Any ideas why? What should we try? Thanks in advance for any help-we are on a fixed income (SS) so it really is...

I'm replacing the hoses from the steering controller to the steering cylinder on an older BX1800. I expect the system will need to be bled, but I'm not sure how to do that. I've looked in a service manual, and searched online, but haven't found detailed step by step instructions. Does anyone...

My Bx1800 has a weird problem the dealer has put 40 hours of wrenching time into it and has no idea what is wrong. When the pto is off the tractor does not have any hydraulic pressure causing the hst to make a grinding sound in forward and reverse. It does not matter if it is in high or low...

Looking at upgrading to the 2670. Looks to be built a little cheaper. Front axle seems smaller and mowing deck appears to be thinner metal. Anyone have any thoughts in comparing these two models?

I'm looking for a decent used BX with mowing deck for under $6000. In that range I've found 1800/2200's and a few 2350's. I know the 2350's had some dislikes and this one has some plastic body damage, but it does seem to be a stronger tractor with a higher rated rear hitch and a newer deck. The...

Ok here's what's I have going on. I have a BX1800, had since new. It will not shut off when the key is placed in the off position. I discovered I had a frozen stop solenoid. Plunger was just "welded" closed. Got a new solenoid but key off will still not shutdown the tractor. The BX1800, at...

I have a BX1800 that I've owned for about 6 years now (bought used, but clean). I've started having an issue where the starter bendix (pinion maybe?)/sprocket that pops out to engage the flywheel isn't lining up properly. So, when I hit the starter, it clicks as the small gear is just hitting...

I've got Kubota BX1800 that I am helping sell for a friend, but not really sure on the pricing. The tractor only has 42.9 hours on it and was wondering how big a role that played in the pricing. Thanks.

I am getting one that was on a bx1800 with a 54" deck. What changes will have to be made to it to fit my 60" deck?

I am asking this for my 80 year old, computer illiterate dad. I am a tractor illiterate daughter, so pardon me if this is totally ignorant. I googled this question, but found nothing close to answering. He has a BX 1800 and wants to know if there is a way to get "down force" on the three...

I got a 600-hour BX2200 this weekend and used it today for the first time. It is very cute - everything is just sooooo teeny - and how I lived this long without a 60" mowing deck is beyond me - BUT, it's REALLY different than my good 'ol L4200GST, so I do have a few questions (some for those...

On my BX1800, the labels on the fuses have worn off. I'm trying to troubleshoot why I have no lights. Can someone tell me what's printed on the fuse block, I can make out some of them, like the stop solenoid. Jim

I was trying to find oil leak took off flywheel without marking any ideas to get back on right

Today the meter showed 1000 hours! It is a 2001 BX 1800 bought new in 2001 with loader (la211) and 54" mid mower. Most hours have been from mowing 3 acres over the years, but has done some amazing rock landscapes in its time. No doubt is the most useful fun tool in the shed. Engine/hst...

Good Afternoon All, Is $7,500 a fair price for a BX1800 with 200 hours and a rotary cutter? Are there any other offers I should consider making given we don't need the rotary cutter and would rather have a front loader and mower? Thanks!

I am looking at 2 used tractors. I would love to buy new, but the cost is prohibiting me. I am looking at a 2003 Kubota BX 1800 with a Loader and 54" MMM for $7800. I took a look at it already and it looks good. Its got about 700 hours on it. I have also seen a 2004 Cub Cadet 5234D with a...

I have a weird problem starting my BX1800. The gist of it is that it will not start while cranking, but as soon as I release the key it will usually start after a few tries. Does anyone have any clue what might be wrong? Mike

I just placed a order for a Frontend loader for my BX1800. Does anyone have any tips. Never had a loader before.

Just got a usd bx1800 and have a couple of questions. The hydro pedal is a little sticky whic I guess I could fix with wd40. The hydro is what I really have questions on. When in 2wd and the lever is on the rabbit, the tractor does not sem to realy go that much faster in forward than in...

Just picked up a BX1800 with 311hrs this past weekend. I used to have a BX1500 a few years ago and should have never gotten rid of it. Glad to be back in the club though. It came with a toothbar on the loader and 5ft Kodiak rear blade. Appears to be in pretty good shape. Couple of things I...

My Kubota BX1800 got too hot at one point, burning a hole in the top of the radiator and melting part of the oil fill cap. Now that I have replaced the radiator ($515) and changed the oil and filters, it runs but burns a lot of blue smoke and almost stalls when operating the belly mower. Anyone...

Looks to me from the kubota parts book that you can fix the fuel sender leak by just taking the left fender an roll bar off, an not the whole floor pan. If so, it doesn't look to be that big of a job. Anybody know if this is the case or not?

A couple generations of recopy but clear enough.

1.Don't know if its the sender or it's a broken spot, but it must be on top because it only leaks when its about full an I am on a hill running crossways in my back property. 2.Now, can you take the roll bar off and unbolt enough stuff to be able to raise/tip the rear of the sheet metal...

I need to restore the pain to the rubber cowling around the front of the kubota what is the best way to do that. Also what is the best paint for the metal body.

I was wondering are there any wheels and tire options for a kubota bx 1800

I need to take this off to sand an repaint it. I can't feel any bolt heads from below. Heck, it seems like theres something under there where you can't get to the bolt heads anyway. The nuts are on the top side out in the open. I was hoping the bolts we're welded on from the bottom side I just...

I just change out my battery and fuses but my headlights and turn signals are not working. I have power to my fuse block and the switches are connected but still no lights they were working.

Hello, I purchase my Kubota BX 1800 with 300hrs about a year ago today. I bought the Kubota because of the color. No its not because it would match my jacket and hat. It was the color for Leukemia and my 11 daughter had just passed away from. My Kubota has been awesome its my second sub...

Where I have moved the oak leaves are abut to overwhelm me So I talked to my dealer and it seems that I can no loner get Kubota bagger. So now what? Anyone know anything about the DR type pull behinds?

Ended up that I gave them 6k tax included for it with the 60 in mmm an 5 ft back blade. But for the extra $250 they went from frt to back an changed, ckd, repaired anything that was wore or broke and sharpened the blades an cleaned it until it looked like new. All filters an oil are now new. 367...

Hello, I obtained a BX2200 parts manual in .pdf and was wondering if it could be used for the BX1800? Does the BX2200 just have a bigger engine? Would there be any differences in the parts manual? Thanks in advance!

I have searched a good bit on this forum and on the web and can't seem to find any information on the BX1800 engine other than it is a 44ci 3 cylinder diesel engine with 18 gross hp. I was hoping to find out engine model name, torque/rpm curves and anything else. I am new to this tractor and I...

Hey everyone...first post! Well I committed to buying a 2000 BX1800 with 900 hours on it today for $4200 with a rear scraper blade. I don't have it yet but I was curious what yall thought about that price. I just bought a house on 8 acres (4 acres grassed) and this tractor is what the...

I am new owner of a used BX1800 and live in N. VT. I wanted to snowblow my drive this morn but couldn't it started. I suspected that I wouldn't since it was -5 out. I am looking to get a block heater. I found the part number and am looking for any advice on the install. Looks like the...

I have a 10 year old bx1800 and the transmission is slipping or bucking going forward when climbing a hill. It doesn't seem to be a problem in reverse. Does anyone have any idea what might be causing the problem. The fluid levels are fine.

I received part #75538-68110 block, with two tapped holes. I installed a single spool valve with power beyond, and now my 3 pth arms will not lift unless i pull handle on remote valve to turn the orbit motor on tiller i have attached to it.

I own the 1999 BX1800, FEL, 54" MMM, 800hrs. Down the street is a 2001 B2910, 60" MMM, FEL, 180hrs for $12,500. I drove the B2910, its certainly bigger, heavier. I like the mobility of the BX, but like the HP and clearance of the B2910. Is a 2910 OK for a lawn or too heavy? About 2 Acres to...

I want to add a hydraulic spool to my BX1800. Does anyone no or have pictures of where to get the pressure from, and also where to return the oil?

I just received my bx1800. it is an older model all metal. it came with a 60 inch MMM a FEL and I purchased a delmorino tiller. I have a question, there are some brush on my property ( 10 ac) and really not much at all, would a rear finish mower be able to take down the brush...

I am receiving a bx 1800 later this week it has a FEL, MMM, and tiller. under 600 hours. I have not come across many threads about the 1800. Is there any reason for lack of threads? also as this is my first tractor does any one have any suggestions at to its dependability. thanks Al...

Hello I just purchase a BX1800 and need a loader does anyone have any leads or tips

Trying to poll the audience... Couldn't find a review about the BX1800 with respect to a backhoe. Is the 18HP sufficient to run the backhoe... I'm not planning on moving he earth but some digging an if I find a big rock I'll dig a hole next to it and pull/push it in. I also plan remove snow...

I have a choice to purchase either of the above, the 1700 comes with a BH while the bx does not I am planning to use it mostly for tilling fields, which one would be better at that, al

I purchased a new to me BX1800 late last year, and now I'm in the process of equiping it with a hydraulic valve and snow blade. The dealer ordered me a BX2015A kit, however the valve included with that kit has all of the connections made at the valve body itself , and it does not have a plastic...

I received delivery of a new to me BX1800 a few weeks ago. I have noticed that it has an issue with creeping forward when left in gear unless light pressure is put on the rear of the hst pedal. I have replaced the neutral return spring and the return damper, but the problem still seams to be...

Mods please delete, posted to wrong forum

hey guys, love these forums. they are so full of info, it's amazing. i was having trouble starting my bx, and almost bought a new starter. But found a sugestion by "KUBMECH"(buying/installing a $30.00 J.D. relay switch), and it starts better than new. saved me LOTS of $$$. i've been having a...

Probably a stupid question, but does anyone know if a Kubota 2650 snowblower will fit on a bx1800? From what I've seen so far, it seems that it may be better suited for a "b" series tractor... I'd like to come up with a snowblower before winter and have been leaning towards a rear mounted one...

where can i buy ag tires for bx1800? iwas just wonder how much they are and if there are any good online sites to find these tires?

Hello, I'm new to this forum and just purchased a '01 BX1800 last weekend. It only has 250 hours and I'm looking forward to start using it. I've only run the tractor for about 15 minutes due to all the rain, but noticed the temperature gauge didn't move. I'm thinking it should have warmed...

The BX25 has been working out great over the past year. I use it all the time for everything around my 12 acres, but I still have to mow the 3/4 acre lawn around the house by hand. With the R4 tires and hillside the 25 really chews up the grass. So I've been looking for a second, smaller, used...

Where do I splice in the heater hoses for best results? Upper & Lower? Block? Any help would be great, my tractor is a square hood Bx1800. Thank you

Yesterday I power washed my tractor. Today I hooked up the front end loader and had used the tractor for about 30 min. I had to get off the tractor to hand load the front end loader with some items and turned the tractor off. Got back on the the tractor would not start. The battery would...

I need a grass bagger for my Kubota BX1800 with a 54" deck, but the local dealers tell me that they are no longer available from Kubota. I'm not sure whether the problem is that there is no adapter to connect a new bagger to my deck to that a suitable bagger is no longer available. Anyone on...

have a kubota BX1800. I have a hydrolic leak in one of the hoses that is underneath the tractor that runs to the hydrostatic transmission. It is blocked so I cannot see how it is connected. I really need the manual or a picture of it. Does anyone have a copy of the BX1800 manual. If someone can...

Well after putting 1200 hours on my BX1800 (bought it new in 2004) I've traded it in on a new B2620. I've only put a few hours on the new tractor so my comments on it will have to wait for a later post. I just want to say a few parting word about the BX 1800 (sniff sniff). The 1800 required no...

My BX1800 with 750 trouble free hours has become a little tough to start. I've had it since new and I have always just turned the key and held it until I hear the first click, then fully turn the key to start it. Over the last few weeks I have found that I need to advance the throttle just a tad...

I have a new / used BX1800, and I managed to run out of diesel with 1/2 a tank showing on the fuel gauge. Can anyone tell me how to reprime the system? Yes, I know I need to order a manual, but I'd like to get back up and running before it gets here. Thanks. Mike

I am considering adding a front end loader on my BX1800 (LA211). I don't see many BX1800 with loaders. Most are on the BX2200 or larger. Are there any issues with loaders on the 18HP BX1800 over the 22HP BX2200? I don't want to put the money into a FEL on the BX1800 if it is too small to...

My stearing feels like there's lots of play, constantly having to move wheel back and forth to control tractor. Replaced the seals in the stearing cylinder a few years ago. I'm thinking it just went out completely that time. Any ideals on what might be the problem? Thanks

I have had a BX1800 with a 54" mowing deck for about four years. I mow a little over 2 acres of lawn. I love the tractor but have always been disappointed in the quality of mowing it performed. In the spring and fall I have to rake the lawn after mowing. The blades do not cut the grass up...

Well my wife thought she knew how to attach a bettery but connected the terminals backwards (pos to neg, neg to pos). Naturally she had some problems trying to start it up. When I got home I checked all the fuses next to the battery and the 30A "slow blow" and none were blown. So I tried...

Anyone using one if so does it work well?

Does anyone have any tips on how to loosen the bolt that holds the fuel filter bracket snugly in place - the filter that is on the underside of the tractor? The bolt is threaded from the top and access to it is extremely limited. The lever that the bracket is mounted to also looks problematic...

Are there any companies making a quick attach system for the loader bucket on the BX18/22 series? I'd like to be able to easily switch from bucket to brush forks, pallet forks, etc. Thanks

I HAVE A 2000 YR BX1800, THE HST LITE CAME ON AND NEED TO KNOW IF THIS IS ANYTHING SERIOUS. EVERYTHING IS WORKING FINE, AND I CHANGED FILTER AND FLUID. IT IS LOCATED ON THE DASH BELOW THE OTHER WARNING LITES. IT HAS THE CORRECT LEVEL OF FLUID. ANYONE OUT THERE KNOW WHAT THIS LITE IS...

I asume I have to replace the alat. How hard its it? (I asume not much more that on a car) How costly is it. (I assume much more than a car)

Hi. I found this site while surfing the web trying to find a solution for my bx1800 steering. After reading several articles, I have learned this is a fairly common problem with these tractors. I have not found anything that tells me how to fix it, which is why I joined this forum. The steering...

I checked at a dealer the other day and they said no.....Is this true?

I drove by my local Kubota dealer tonight when it was closed. There were two BX1800's setting out in the parking lot with a big sign on them. I stopped by and took a look at them. One had 30 hours, and the other had 40 hours. This dealer was asking $5500.00 for each BX1800. This price is...

Anybody ever burst a hose? I've searched these archives and I don't see this happening to anybody. Newbie BX1800 owner here - bought it used with 320 hours on it a couple weeks ago. It came to me in excellent condition, no signs of any abuse at all. The prior owner certainly wasn't afraid to...

Im glad I traded in the O'l GT235 on this thing, although I wish the dealer would hurry up and sell my Gt235, I guess this isnt garden tractor season.

My BX1800 Temp needle now goes into RED after 15 minutes of using the belly mower. The Radiator & overflow have anti-freeze. The radiator, radiator filter, etc, are free of debris. I've been using since new in 2000 without a problem. Any ideas on what has happened? Thanks.

Hello, Was looking for a quote on a kubota bx1800 that was willed to me. Still has quite a bit left on the loan. Have someone interested in it but was wondering what these go for used (dont want to get taken advantage of)? Only has 92 hours on it and is in great shape. Thanks for any help it is...

48\" bushhog on a bx1800 my manual says use a 42" but 48" is a lot cheeper (I guess they make more of them) So will 6" more be a big deal?

I've searched through the forum for the answer to this and am coming up empty-handed. Help! I'd like to buy a small bush hog for my Kubota BX1800 to mow the ROW and other areas on the farm that are either too rough for the BXs' belly mower or won't be mowed by the neighbor who has the hay lease...

WOODS BACKHOE ANY BODY HAVE ONE OF THESE WOULD LIKE SOME INFO THANKS

In the market for a rotary tiller for mom's BX1800. Our dealer gave my mom a quote for a 42" and 50". Saying both would work on the BX(he is our Kubota dealer). So I'm trusting they would fit the "limited" hitch. No front ballast required(no loader on BX). I'm leaning toward the 50" since it...

I am working on some projects for my BX23, and I was curious how similar the Kubota LA210 and LA211 loader assemblies are to the loaders that come on the BX1500 and BX1800 machines. If anyone is willing, could you take a look at these pics and measure the dimensions I have marked off? Basically...

BX1800 won\'t start My BX won't start - acts like the drive lever was engaged but it is not. All fuses check okay. Suspect safety switch is stuck but don't know where to look. Gerry

Howdy. I'm new here and need a little info. Due to impending divorce and sale of property, I need to sell my relatively new BX1800. 139 hrs, loader and 54" mid deck. Also have a 4' HEAVY rear blade. Real good shape - a scratch or two, that's it. What's a good price? I can't find anything...

Looking for a dedicated mowing machine for my parents...Please see this post Another dedicated mower question . The same dealer we are demo-ing the G1800 just got a BX1800w/54" deck turned in. It has 510hr and is described as very clean. Asking $7,200. Opinions on price? The problem is I...

I am cutting a chunk of steel to bolt to the front for a weight and forgot the mesure how tall the frame is. Also if you happen to know the size and spacing of the bolt holes it sure would help me. Save me a trip back to the house anyhow. Thanks

Ok all you other BX owners. Here is a question and I am sure you will just shake your head and laugh but, here it goes. Keep in mine I am Polish if that helps. I have a BX22 and want some better headlights. Does anyone know or know anyone that has installed H.I.D on there tractor? HID stands...

Does any one know who makes a good front grill guard for a BX 1800/2200 without a Front end loader? <font color="blue"> </font>

I bought a new BX1800 in June and sort of wish I had found this forum before then. I've since spent hours going through old messages and guess what I found? Everybody loves their BX! Although I've only used mine for mowing so far (20 hours), I can't wait (sort of) for winter as I want to see...

I purchased a demo BX1800 two weeks ago with about 55 hours on it. The dealer did no service to it so I asked them for the fluids/filters. They have not found the owners manual and have ordered one for me and I need to know where to clean the screen out when I change my fluid and filter. Thanks

Well I finally got a chance to plow the garden tonight. Between all the rain we've had (who hasn't right?) and getting my rear hitch built, I am only about 1 month behind normal schedule. Well I gotta say that this BX1800 is the cats meow!!! I used to do this with my old Cub 1811 and had to...

Just had to replace a hyd hose on the wife's BX.What a job! It went from under the steering wheel to beside the left rear tire.By the time I got it off it didn't even look like a tractor.Under the steering wheel was the worse.I had to grind the sides down on a 11/16 open end wrench to get to the...

Found a BX1800 today at a dealer. Not sure of the year but it has 200 hours. Has 54"MMM and 211FEL. Asking $9000. Is this price in the ballpark? Or should I just pursue a new BX2200 with MMM and FEL for about $12450. Either rig should fit my bill. This is all so much.... too may decisions...

Look to see if BX1500 is what I need? My Needs: Mowing 3 acres of lawn(40 Hours per Year), mowing around pond(10 H/Y) and ditches, and trail work on 10 acres of woods(20 H/y). To use for light winter clean up off 500 foot driveway(10 H/Y) and spring maintaines(5 H/y) Have a friend to...

Finally after nearly 3 weeks, my 1800 is on the way. This past week has been sooooooo long..........as Carvers has been waiting for a truck to pick it up. Talked to them today and it was on the truck and scheduled for Monday. The truck driver also called and he wants to drop it off TOMORROW...

let's see if i figured this bx1800picture out

finally broke down today and bought me a bx1800. paid 9900 with a 54 inch deck. i know it's kinda high, but he wouldn't budge, and i love the bx. just wanted to let every know and this is one hell of a site. should take delivery on it maybe as soon as friday afternoon. i'll take pics and keep...

Well I've been reading the posts here for about 3 weeks now and gotta say I am getting hooked. Feels like a bunch of guys out in the garage standing around the "New Toy" gruntin, drinkin beers and enjoying the stories. So here goes my story..............Well February 15/16th we had a nice bit...

<A target="_blank" HREF=http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=1923023606>BX1800 976 hours</A> Some one leave the key on?

Thanks to all who replied to my questions here on TBN. The information here allowed me to take a realistic look at my needs now and guess about in the future. I was looking to purchase the BX2200 with FEL, 60" MMM, which would have put me out of my financial comfort range. I know, in the long...

OK, I made my best price on a BX1800 with 54" mower for $9,300.00 w/o tax. (Central Virginia). Also got a price on Woods 5' rear blade $330.00 and a J-Bar box scraper $329.00. I think its a good price. The bank says "fax us the buyer's order-we'll cover you", the dealer says "say the word we'll...

Seriously looking at a BX1800 after owning (happily) a JD 445 for six years. Looking for the diesel and 4wd upgrades as the bigger part of my rationale. I cut a little over 4 acres and I don't need a loader. I would probably buy a 60" MMM and front hyd blade for snow and a box blade or rear...

I just returned from my local dealer. I've been considering a BX2200 / 60" deck, but today my delaer tells me Kubota is offering a $300 rebate on the BX1800 w/54" deck. Since I will use the tractor for primarily mowing, I'm not sure if I can pass up the deal on the BX1800. He quoted a price of...

I want to thank all of you for your comments. I called the dealer today and told him to put my name on the 1800 w/54". Will pick it up early next week. So I should start posting really stupid usage and attachment questions real soon!

I called the dealer today, told him to put the 1800 w/54" on hold. Lot of money... but lot of tractor too!

Hello all - I'm looking for some input for a (hopefully) upcoming purchase. I am in a residential area (so the BX series is probably overkill), but the toy factor of the FEL is too great. I am looking into a subcompact because I have an auxiliary drive and large level pad that is pea gravel...

Can someone tell me a fair price for a new kubota loader for my bx1800. I have got pricing from two local dealers, there is a $650.00 difference.

I am looking for suggestions for the best loader to fit my bx1800. What is a fair price for a new loader? Who has the best bang for the buck? Thanks

what a great forum,just found it tonight. i am trying to talk the wife into a new tractor. we have 3 acres of lawn and some woods.i have 2 sears 12hp mowers now w/38"deck,i use one for parts. both i got for free and have been keeping them going since we moved in 4 years ago. i am looking at the...

I'm considering buying a new BX1800 and 54 inch belly mower but I'm wondering if it may be too much tractor for my lot. I have a flat half acre of grass and no obstacles. I would also like to add a snow blower as funds become available. Any thoughts?

Thanks guys for the replies... I did take the day off. However, dealer called....said there would be a delay. The Curtis cab I had ordered seemed to be missing parts..Oh well. When Christmas shopping instead..... Hopefully delivery will be early next week!

Have really enjoyed reading all the posts over the last month. Very informative & helped decide what to buy!!. Have OnOrder a BX1800, I have small 1 acre lot..so should do fine! Thanks to all for contributing! Maybe delivery tomorrow!

Went to dealer yesterday to look at the bx2200. I was thinking of buying one in the spring. The dealer came right out and said he would sell me a new bx2200 with 60" mmm, fel, and loaded turf tires for $11,800. Looking at previous posts this seems like a great price. We talked some more and he...

Hey Guys , This might be a first here but I will try to explain this as well as posible .. I am going to get the BX1800 based on a few things as well as being a very good sub compact tractor ,, As result of an accident in 1980 I have been using a wheelchair , I have no use of my legs...

I am looking to get a BX model and there is a BX1800 at the local dealer that I might get at $7900.00 (tractor only)Is that a good price ? And also I dont see many discussions on the BX1800 . Is the BX1800 underpowered ..?I will be using the FEL and boxblade I am going to get the FEL and...

After weeks of considering options, took delivery on a BX1800, FEL and rear blade. Thanks for all the great posts which helped tremendously (first tractor). Hope I can help someone else in some small way in the future. Have 5 hours on the new baby so far, love it!

I have 55 acres of steep hilly woods, with about 2.5 acres of lawn. The lawn is all hillside (as is most of VT). I currently have a 430 Gravely (rear engine) with tire chains. There are four passes I have to make going up, because when I go downhill the tires slide. When going up I have to...

looking to buy small tractor to move boats at a boat shop\ my local dealer is trying to sell me a bx1800\ he has a b7300 hsd that is last years model that he will sell for the same price is there an eaasy way to tell how long this tractor has been sitting on his lot\ i will buy a mower deck to...

I just bought a new BX1800 with FEL and 4ft scrape blade, should I leave the blade on for weight, or better leave off, is this better for less weight on the tractor

I recently bought 2.5 acres of land. There are no trees or hills on the property. The land is flat. I primarily will be using my BX for mowing the entire property. I'll do other odd jobs using the tractor. Because of a tight budget is the BX1800 a better tractor for my needs.

It was finally warm enough to brush hog our new pasture. We moved in early December and I have been hoping the BX1800 would be able to handle the 48" bush something(Woods brand) on the 30-45 degree portions on the hill and pond embankment. I don't have the nerve to try to go sidewise over this...

Okay. So I want a Kubota. With a loader and a mower. I've left the city for 3-4 wooded, lakefront acres in mid-Virginia. I need to move rocks and sand and mulch and to scrunch up leaves. I've been paying too much to a guy with a bobcat and wheelbarrows get real old after a while. So... Do I...

I've never owned a tractor before and I'm looking for my first. I am currently considering either a new BX1800 with a loader for $9,995 or a used B1550 with a kubota loader for $7000. The B1550 has low hours, I don't recall the number but the dealer is advertising it as being like new, and from...

I have 10 acres and am looking for a tractor for Lawn care, snow plowing (only a blade), box scraper for makeing a trail around the property, sand rake for the riding arena, post hole digger for the fencing and potential other attaschments. In a nutshell, should I be buying the attachments from...